Boundmotor D3 Direct Drive Electric Skateboard User Guide
- June 13, 2024
- Boundmotor
Table of Contents
D3 Direct Drive Electric Skateboard
User Guide
WARNING
RISK OF DEATH OR SERIOUS INJURY
Whenever you ride a board, you risk death or serious injury from loss of
control, collision, and falls.
To ride safely, you must read and follow the instructions and warnings in the
manual.
Always wear a helmat when riding. Avoid water, wet surfaces, slippery/ uneven
surfaces, steep hills, traffic, cracks, tracks, gravel, rocks, or any
obstacles that could cause a loss of traction and cause a fall.
Avoid night riding, areas with poor visibility, and small spaces.
Warning: Do not ride on side-hills or on an incline of more than 10 degrees.
Do not ride at speed which you would not safely control the board. In case of
wireless interface or battery error, you may need to rely on skating
techniques like foot braking or sliding to stop.
WARNING: AVOID WATER!
Your board is not completely waterproof,you can easily go through the puddles
but don’t soak the board in the water. Water damage is not covered under the
warranty.
WARNING: PINCH POINTS!
Keep fingers, hair, and clothing away from belts, motors, wheels, and all
moving parts.
WARNING: RISK OF ELECTRONIC SHOCK!
Do not open or tamper with electronics housing, which also voids the warranty.
PROTECT’ION
- ALWAYS WEAR A HELMET
- Find an open, flat area with clean pavement for your first ride.
- Read the warning on the skateboard and at the beginning of this manual.
OTHER RECOMMENDED PROTECTION EQUIPMENT
- wrist guards
- elbow pads
- knee pads.
Move the Throttle Wheel in small increments.
Keep a wide stance on the board.
Keep a low center of gravity.
Lean forward when accelerating.
lean backward when braking.
OVERVIEW
SPECIFICATION
PERFORMANCE
Max. User Weight: 120kg / 265 Ibs
Max. Range:25-30 km(12s2p) 40-45km(12s3p) Riders weight: 75KG.
Speed Mode: 30km/h 40km/h 50km/h
BOARD
Deck Material: Canadian Maple / Carbon Firber
Wheel Material: Rubber
Battery Type: Li-ion
Battery Cell Quantity: 24/36pcs
CHARGER
Input: AC 100-240V Max. Output:50.4V / 4A
CONTROLLER
Material: ABS Plastic
Battery Type: Lithium
Wireless Connection: 2.4 GHz
CHARGIETHEREMOTEY/BOARD
There is a switch on the back of the charger, 110v or 220v, Make sure to
switch to the corresponding voltage mode.
Otherwise, the board can not be full charged.
LED | ACPOWER ON
LED 2 CHARGER CONNECTED
LED 2 CHARGING
LED 2 FULLY CHARGED
CHECKTHE REMOTE/BOARD BATTERYLIFE
ORPERATETHE BOARDWITHTHEREMOTE
Push the throttle forward to accelerate.
Move the Throttle Wheel in small increments.
Keep a wide stance on the board.
Keep alow center of gravity.
Lean forward when accelerating. Pull the throttle backward to brake.
Move the Throttle Wheel in small increments.
Keep a wide stance on the board. Keep a low center of gravity. Lean backward
when braking.
PAIRING
Hold the power button with the GEAR button until the 4 red lights blinks.
Then, turn on the Vesc with the power button (Vesc) and they should pair up
automatically.
VESC
If you are not familiar with
VESC, please do not change any settings.
defects or malfunction caused by misuse, abuse or improper maintenance are not
coverd under the warranty.
NOTE:
Please do NOT upgrade the firmware, if you have upgraded the firmware to v4.2,
some functionality will be lost, such as speed mode switching and front-back
direction switching.
Use VESC tool V1.29 to customize your settings, link:
https://bit.ly/vesctool
BATTERY’SAFETY
The lithium-ion battery can explode or cause a fire if they are used
incorrectly.
Therefore, it is recommended to read the following instructions very
carefully:
-
Before riding the board, check the battery pack carefully, especially the protective seal.
Make sure it is undamaged and intact. If in doubt, take the battery to a chemical waste disposal facility. -
Never drop the board.
-
Store the board with battery inside in a dry place.
-
Never expose the battery to a temperature above 100-celsius degrees.
-
Only use an official board charger for charging board battery.
-
Never leave the board unattended when charging.
-
Never make the board work when charging.
If you are not planning to use the board for about 6 months or longer, charge
fully and charge it once a month.
A lithium-ion battery that has been left empty for too long, the battery will
no longer be rechargeable.
- Charge the battery for 6 hours before first-time use. This gives it a better long-term performance.
WARRANTY
LIMITED WARRANTY:
This board is covered under 180 – day warranty that covers defects in
workmanship and material.
This does not cover damages caused by abuse, misuse, negligence, accident, or
riding in water.
If the product has a manufacturing defect within180days since the shipping
date, please contact the dealer before shipping the board back:? in order to
get a return authorization.
FOR ALL RETURN AND WARRANTY SHIPPING:
Please keep your shipping box. The warranty does not include damage from
shipping in insufficient packaging.
CONTACT’US
hello@boundmotor.com
+1(602)730-4536
https://twitter.com/boundmotor
https://www.instagram.com/bound.motor/
https://boundmotor.com
BOLNVOTCR.COM
CAUTION: DO NOT SHORT-CIRCUIT, DISASSEMBLE.
OREXPOSE THE BATTERY TO FIRE ORWATER
References
- Next-Generation Electric Skateboard and DIY Accessories
- Manual-Hub.com - Free PDF manuals!
- BoundMotor (@bound.motor) • Instagram photos and videos
- Performance Electric Skateboards Online | BOUNDMOTOR
- BoundMotor (@bound.motor) • Instagram photos and videos
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>