EKVIP 023274 Wall Mounted Spotlight Instruction Manual

EKVIP 023274 Wall Mounted Spotlight

Product Information

• Product Name: Wall Spotlight
• Model Number: 023274
• Manufacturer: Jula AB
• Power Supply: 230 V ~ 50 Hz
• Power Consumption: 2 x 3.5 W
• Protection Class: IP54

Product Usage Instructions

1. Mounting:
   • Identify the desired mounting holes and mark them.
   • If necessary, drill holes and insert expansion plugs.
   • Attach the base plate to the mounting surface.
   • Connect the wires to the terminal block.
   • Attach the spotlight to the base plate.
   • Connect the power supply.
2. Disassembly:
   • To remove the base plate, unscrew it using an Allen key.
   • To disassemble the lamp and drive unit, unscrew the screws using a star screwdriver.
3. Maintenance:
   • To clean the mesh cover, unscrew it using a cross-shaped screwdriver.
   • To clean the housing, unscrew it using a cross-shaped screwdriver and remove the cover.
   • To replace the bulb, unscrew the drive and lamp plate using a cross-shaped screwdriver, and then remove the drive and plate.
   • To replace the glass, lift it using a flat screwdriver and remove it.
   • To remove the base plate, unscrew it using an Allen key.

Jula AB reserves the right to make changes to the product. Jula AB claims copyright on this documentation. It is not allowed to modify or alter this documentation in any way and the manual shall be printed and used as it is in relation to the product. For the latest version of operating instructions, refer to the Jula website.

SAFETY INSTRUCTIONS

• For outdoor use.
• The product must be connected to an earthed power supply on installation.
• The electrical installation must comply with local regulations. Consult an authorised electrician if in doubt.
• Always follow the electrical specifications on the product labelling.
• Always disconnect the power supply before installation, connection and service.
• Never modify the product, this could result in serious personal injury and/or material damage, and will invalidate the warranty.
• The product gets hot when it is switched on. Do not touch the product with bare hands.

ELECTRICAL SAFETY

New installations and extensions to existing systems should always be carried out by an authorised electrician. If you have the necessary experience and knowledge (otherwise contact an electrician), you can replace power switches and wall sockets, fit plugs, extension cords and light sockets.
Incorrect installation can result in fatal injury and the risk of fire.

SYMBOLS

TECHNICAL DATA

• Rated voltage 230 V ~ 50 Hz
• Output 2 x 3.5 W
• Protection rating IP54

INSTALLATION

IMPORTANT:

• Make sure the mains supply is disconnected before installation.

• Check that there are no concealed electrical cables, gas and/or water pipes where the holes are to be drilled.

  1. Switch off the power supply.
     FIG. 1

  2. Undo the screws holding the back of the light.
     FIG. 2

  3. Mark out where to drill the mounting holes.

  4. Drill the holes and insert expander plugs if necessary.
     FIG. 3

  5. Make a small hole in the entry for the power cord. Insert the power cord through the entry.

  6. Screw the base plate to the wall.
     FIG. 4

  7. Connect the wires to the terminal block.
     – L = Brown
     – N = Blue
     – Earth = Green/yellow
     FIG. 5

  8. Fasten the light on the base plate.
     FIG. 6

  9. Switch of the power supply.

REMOVAL

• BILD 7
  Unscrew the mesh cover screws with a cross screwdriver and take out the mesh cover.

• BILD 8
  Unscrew the cover plate screws with a cross screwdriver and take out the cover plate and shutter.

• BILD 9
  Unscrew the screws of the drive and the lamp plate with a cross screwdriver, and take out the lamp plate and the drive.

• BILD 10
  Pry open the glass with a slotted screwdriver and take it out.

• BILD 11
  Unscrew the base plate with an Allen wrench and take out the base plate.

• BILD 12

MAINTENANCE

NOTE:
Switch off the power supply before cleaning.

1. Switch off the power supply to the light.
2. Wipe the light with a dry or slightly damp cloth.
3. Wait until the light is completely dry before switching the power supply on again.

NOTE:
Do not use detergents, alcohol, solvents or the equivalent to clean.

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>