ATOMSTACK M150 160W 6-Diode Cores Laser Module Instruction Manual

ATOMSTACK M150 160W 6-Diode Cores Laser Module

AtomStack M150 Laser Module
The AtomStack M150 Laser Module is a laser engraver system component that must be installed in other manufacturers’ laser engravers for use. The laser module belongs to Class 4 laser products and requires the laser system itself to meet the requirements of IEC 60825-1 latest version. Failure to meet these requirements prohibits the use of the product.

Product Information:

• Product Name: AtomStack M150 Laser Module
• Model Number: F03-0192-0AA1
• Version: A

Security Statement and Warnings:

1. Read the safety guide carefully before using the laser engraving system. It contains important information about situations that require special attention and warnings of unsafe practices that can cause damage to property or personal safety.
2. The laser engraver must have a protective housing that prevents human access to laser radiation.
3. If the protective housing has an access panel providing walk-in access:
   • A means should be provided for anyone inside the protective housing to prevent activation of a laser hazard equivalent to Class 3B or Class 4.
   • A warning device should be positioned to adequately warn of emissions of laser radiation equivalent to Class 3R in the wavelength range below 400 nm and above 700 nm, or emissions equivalent to Class 3B or Class 4.
   • If walk-in access during operation is intended or reasonably foreseeable, engineering means must be implemented to prevent emission of laser radiation equivalent to Class 3B or Class 4 while someone is present inside the protective housing of a Class 1, Class 2, or Class 3R product. This can include pressure-sensitive floor mats, infrared detectors, etc.
4. The laser itself is equipped with a protective cover that should be securely fastened with screws when installed on the laser engraver. The protective cover should not be removed in the energized state.
5. The housing of the laser engraver should have an interlock function that automatically turns off the laser when opened or removed.
6. An emergency stop button should be present on the laser engraver to immediately stop the laser output in unexpected circumstances.
7. A reset button should be available on the laser engraver to resume work after confirming safety by lifting the interlock or emergency stop.
8. The laser engraver should implement physical keys, dongles, password systems, or other means of management and control to prevent unauthorized personnel from operating the equipment without security training.
9. Any window or channel on the laser engraver that can actively observe or passively receive laser radiation should be marked with warning signs.
10. In case of laser burns to the skin or eyes, seek immediate medical examination and treatment at a nearby hospital.

Disclaimer and Warning:
This product is not a toy and is not suitable for individuals under 15 years of age. Keep the laser module out of reach of children and exercise caution when operating in environments with children present.

F03-0192-0AA1 Version: A

Security Statment and warning

Before Using the laser engraving, please read this safety guide carefully, it mentions situations that require special attention and includes warnings of unsafe practices that can cause damage to your property or even endanger your personal safety.

1. This product is a laser engraver system components, must be installed in other manufacturers of laser engraver for use.And the product belongs to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version, other-wise the product is prohibited to be used.
2. Your laser engraver shall have a protective housing which, when in place, prevents human access to laser radiation.
3. If a protective housing is equipped with an access panel which provides “walk-in” access then:
   • means shall be provided so that any person inside the protective housing can prevent activation of a laser hazard that is equiva-lent to Class 3B or Class 4.
   • a warning device shall be situated so as to provide adequate warning of emission of laser radiation equivalent to Class 3R in the wavelength range below 400 nm and above 700 nm, or of laser radiation equivalent to Class 3B or Class 4 to any person who might be within the protective housing.
   • where “walk-in” access during operation is intended or reasonably foreseeable, emission of laser radiation that is equivalent to Class 3B or Class 4 while someone is present inside the protective housing of a Class 1, Class 2, or Class 3R product shall be prevented by engineering means. NOTE Methods to prevent human access to radiation when persons are inside the protective housing can include pressure sensitive floor mats, infrared detectors, etc.
4. The laser itself has a protective cover, the protective cover is fastened by screws. When the laser is installed on the laser engraver, the protective cover should be checked to be reliably locked, and can not be removed in the energized state.
5. The housing of the laser engraver should have an interlock function. When the housing is opened or removed, the laser can be automatically turned off.
6. The laser engraver should have an emergency stop button, which can immediately stop the output of the laser when pressed under unexpected circumstances.
7. The laser engraver should have a reset button, which can resume work under the condition of confirming safety after lifting the interlock or emergency stop.
8. Laser engraver should use physical keys, dongle, password system and other ways to manage and control, to prevent personnel without security training operation of this kind of equipment.
9. On the laser engraver any window or channel that can actively observe or passively receive the laser radiation should be set up warning marks.
10. If the laser burns the skin or eyes, please go to a nearby hospital for examination and treatment immediately.

Disclaimer and warning

• This product is not a toy and is not suitable for people under 15 years of age. Do not allow children to touch the laser Module. Please be careful when operating in scenes with children.
• This product is a laser module, visit http://www.atomstack.com/laserengraverdownload for complete “user manual” and the latest instructions and warnings. Shenzhen AtomStack Technologies Co., Ltd. (Atomstack) reserves the right to update this Disclaimer and Safe Operation Guidelines.
• Please be sure to read this document carefully before using the product to understand your legal rights, responsibilities and safety instructions; Otherwise, it may bring property loss, safety accident and hidden danger of personal safety. Once you use this product, you shall be deemed to have understood, accepted and accepted all terms and contents of this document. User undertakes to be responsible for his or her actions and all consequences arising therefrom. User agrees to use the Product only for legitimate purpos-es and agrees to the entire terms and contents of this document and any relevant policies or guidelines that AtomStack may establish. You understand and agree that AtomStack may not be able to provide you with the cause of the damage or accident and provide you with AtomStack’s after-sale service unless you provide the original engraving or cutting files, engraving software configuration parameters used, operating system information, video of the engraving or cutting process, and operational steps prior to the occurrence of a problem or failure.
• AtomStack is not liable for any and all losses arising from the user’s failure to use the product in accordance with this manual.
• Atomstack has the ultimate right to interpret the document, subject to legal compliance. Atomstack reserves the right to update, modify, or terminate the Terms without prior notice.

Accessories list

Installation method

If the machine is as shown in the figure below, please install the dovetail slider
Remove the original laser and laser fixed slider The fixed slider of M150 module is a dovetail slider. If the original machine slider is also a dovetail slider, the M150 module can be directly installed and used;

1. Remove the original laser and laser fixed slider
2. Replace slider
3. Replace the dovetail slider in the accessories and fix it with M5*10+M5 gasket

If the machine is as shown in the figure below, there is no need to install the dovetail slider

For users who want to use the previous laser module after replacing the cable, we have provided a conver-sion cable, please choose according to your needs

Wiring method

Note:
The driving current of M150 module is relatively large, you need to use the equipped motherboard cable

• A lot of smoke is qenerated in engraving or cutting wood and other obiects.be aware of cleaning the air quide hood and anti-skid cover,since there may be a lot of dust accumulation on itespecially working with more than 50% of the laser power.
• Remove the shield if you couldor tum on the air assit while machine working,all of which would significantly reduce dust accumulation.

The laser dower of this machine is very hiah. if you need to cut wood and other fammable materials with a power of more than 70%, please ensure someone is watching the machine in case of the flammable materials catches fire.

Cautions

LASER BEAM CAN DAMAGE EYES

1. Laser Light can damage the human eyes and skin. Do not expose the eye or skin to laser light directly.
2. This Laser product has an optical lens and emits a collimated laser beam.
3. The light from this product, both direct and reflected, is very harmful as it can propagate a long distance while maintaining high optical density.
4. When handling the product, wear appropriate safety glasses (OD5+) to protect eyes from laser light including reflected and stray light.
5. The reflected and stray light spilling into an unintended area should be attenuated and/or absorbed.

Maintenance instructions and warning

This product uses a highly integrated design and requires no maintenance. However, if the laser system installed with this product needs to be repaired or tuned, please:

1. Unplug the power cord on the laser, so that the laser is in a state of power failure;
2. If you need laser assistance for tuning, please:
3. All present personnel wear protective glasses,OD5+ protective glass is needed ;
4. Make sure there are no flammable or explosive materials around;
5. The position and direction of the laser are fixed to ensure that the laser will not accidentally moveand shine on people, animals, flammable, explosive and other dangerous and valuable objects during debugging.
6. Don’t look at lasers
7. Do not shine the laser on the mirror object, lest the laser reflection cause accidental injury.

Customer Service

• For detailed warranty policy,please visit our official website at: www.atomstack.com.
• For technical support and service,please email: support@atomstack.com.

Manufacturer:
Shenzhen AtomStack Technologies Co., Ltd.

Address:
17th Floor, Building 3A, Phase II, Intelligent Park, No. 76, Baohe Avenue, Baolong Street, Longgang Dist., Shenzhen, 518172, China.

Scan the code to enter the discussion group.

Scanner APPLICATION:
QR code reader/Barcode scanner or any APP with scanner.

References

• AtomStack Official Website | Unleash Your Creativity With Laser

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>