global sources LT-828 AUTOMOTIVE Wi-Fi Router User Manual

global sources LT-828 AUTOMOTIVE Wi-Fi Router User Manual

1. Product Introduction

ZBX-BS01G automotive Wi-Fi router is a high-performance industrial-grade router. This product is suitable for automotive environment, and its CPU frequency is 560MHz, which can easily deal with various applications. The hardware based on Qualcomm’s Atheros WiFi technology has super performance and strong anti-interference ability, so that the BS01G car router can work stably in various complex application environments.

ZBX-BS01G automotive Wi-Fi router can work normally from -40 ° C to 85 ° C, QoS flow control mechanism will ensure clients get better user experience, high-quality mobile communication module will support most regions and countries in the world Mobile operator network.

This product will adapt to different types of communication modules for different regions and
countries. For details about the applicable regions or countries corresponding to different types of communication modules, see the attached table.

2. Hardware index

2.1. Basic parameters
a. Working temp： -40°C~85°C
b. Storage temp： -50°C~95°C
c. Humidity： 0~90% , No condensation
d. Input voltage：9~32VDC
e. Rated consumption：<6W
f. 2.4GWIFI Transmit power：25±2dBm
g. Dimension：183x160x42mm
h. N.W.：0.65kg

2.2. Structural characteristics
a. The shell is made of LG chemical vehicle plastic materials that meet environmental protection and flame retardant standards.
b. The embedded design of the metal panel with high heat dissipation ensures that the device still maintains a strong working state in extremely complex environments and reduces the impact
on WiFi performance.
c. The power supply interface adopts the aviation head connection mode, which is firm and reliable.
d. A removable galvanized metal rack is used for easy installation.
e. The SIM card slot used for GSM network is designed with a removable cover to facilitate SIM card insertion and removal.

2.3. Product specification
Hardware parts

a. Power Input：x1
b. LAN input：x1
c. WAN input：x1
d. Reset button：x1
e. GPS Antenna port：x1
f. SIM card slot：x1
g. Working indicator：x1
h. 4G signal indicator：x1

Wi-Fi parts
a. Wireless transmission standard：802.11b/g/n
b. Frequency：2.4GHZ
c. Auto detection：1/2/5.5/11Mbps(IEEE802.11b), 6/9/12/18/24/36/48/54Mbps(IEEE802.11g), 300 Mbps(IEEE802.11n)
d. Wireless transmission distance：≤ 100 m（The actual situation is decreasing due to different
environments）

2.4. Accessories
a. Hanger：x1
b. Manual：x1
e. Screws KM3*10（T10）：x1
f. Wrenches（T10）：x1

3. Operating instruction

3.1. Installation instruction

1. After determining the installation position of the router, first fix the router hanger to the
   installation position. 4 screws are needed to fix hanger, and its specifications will be determined by the client according to the structure of the installation site in the vehicle. As shown in Figure 2

2. According to the length of the power cord of the configured router and the specifications of the harness connector, the user needs to design and lay out the power output cable in the vehicle to the installation location in advance.
    Range of input power voltage：9-32VDC

3. Open the SIM card slot cover of the router, insert the SIM card in the indicated direction and fasten the cover. As shown in Figure 3

4. This product supports GPS antenna access. GPS antenna is optional and not included in the package. If the customer selects a GPS antenna, connect a GPS antenna to the GPS antenna connector of the router. As shown in Figure4

5. Connect the power cord end of the router to the power output line in the vehicle, and turn on the power switch in the vehicle to get the normal power supply to the router. At this time, the status indicator lights up and off when working normally, and the abnormal condition is always on or off.

6. After the router is turned on and working normally, align the four bolts at the bottom of the
   router with the corresponding empty positions of the hanger; at the same time, push hard in the indicated direction to make the bolt and the mounting hole of the hanger form a tight fit, then hang the router upside down on the hanger. As shown in Figure 5

7. Lay the GPS antenna to the side of the vehicle centering on the installation position of the router, and fix the patch on the other end of the antenna horizontally to the lower edge of the vehicle window or the position where sun could shine. As shown in Figure 6

8. It is recommended to install the on-board router in the middle of the center of the bus or on the surface of the luggage rack on both sides, which is conducive to the laying of power cables inside the vehicle and GPS antenna installation and Wi-Fi signal transmission.

9. When the router is connected to the power supply, the running status (blue) indicator lights on and flashes about once every a second, indicating that the device system is in working state; when the 4G signal (green) indicator lights on and with the following phenomena correspond to the following status：
   • Flashing slowly: searching signal status
   • Flashing slowly: stand-by status
   • Flashing fastly: data transmission mode

10. After confirming that the router enters the standby state, turn on the mobile communication device (mobile phone or tablet)-Settings-turn on Wi-Fi, select the default SSID of the device: Wi-Fi, click to connect to this Wi-Fi hotspot. For the Wi-Fi name, please refer to the relevant content of this manual, and log in to the background to make custom changes.

11. Make sure that the mobile communication device and the router can normally link and log in to the Internet. At this time, use the T10 wrench of the fixing screw in the accessory to fix the KM3 * 10 (T10) screw to the router and the hanger. As shown in Figure 7
    • If cannot connect to the Internet at this time, change or reset according to the relevant prompts in the “Setup Instructions” and restart the power supply and link again.。

3.2. Application scenario
When the installation and connection are completed, no matter whether the bus is running or
stopped, only need to provide normal power supply to the router and confirm that the router is also within the coverage of the mobile network signal. Users can enjoy the Internet life, browse the web, log in Social platform, keep abreast of the ever-changing external world, learn from the massive information, and make life more convenient and beautiful! As shown in Figure 9

3.3. Setup instructions
After the router is powered on, you can log in to the background of the router and manage the
router according to the user’s local requirements. The specific operations are as follows：
a. Click to run any browser (the computer or laptop must be connected to the router with cable or wifi), enter the router’s default LAN IP address [192.168.1.1:8088] in the browser address bar, press Enter, and automatically enters the router login page, then input user name and password that are both set as “root” by default. As shown in Figure 10

Figure 10

b. Input the login password and click “Login” to enter the router background management page.
The default setting is the English page. If the user needs to switch languages, they need to click
“System”-“Language” in the navigation menu on the right side of the page In the language setting window, click the drop-down arrow to select the desired language-click “Save & Apply”-
refresh the page or click the content of the navigation menu on the left side of the page to
complete the language switch. As shown in Figure 11

c. Click “Status Information” in the menu bar. The right side of the page displays information about the real time working status of the router. All contents on this page are the default settings, and there is no need to change the settings.
d. Click “Route Settings” in the menu bar, and the configuration information of the “WAN” port is displayed on the right side of the page. Some settings need to be changed according to the information provided by the local operator. If you need to return to the settings before the change, click “Reset” at the bottom right of the page to restore the factory default settings. Otherwise, click “Save & Apply” to complete the setting changes. As shown in Figure 12

Refer to the following instructions for the setting changes. As shown in Figure 13

• The default setting of “Protocol” for Internet access is “3G / 4G”, users can click the drop-down arrow according to the way the router connects to the network, and select the desired content from the drop-down bar to make settings changes.

• The default setting of “Modem Node” is “/ dev / ttyUSB3”, this setting cannot be changed.

• The default setting of “Service Type” is “LTE-4G”, users need to click the drop-down arrow according to the local operator’s SIM card network standard, and select the required content from the drop-down bar to make settings changes.

• The default setting of “APN” is “China Unicom”. If the user needs to change this setting,
  must be changed according to the relevant information provided by the local operator.

• “PIN” field is blank, no need to change settings.

• The default setting of “PAP / CHAP User Name” is “card”. If the user needs to change this
  setting during use, the setting must be changed according to the relevant information
  provided by the local operator.

• The default setting of “PAP / CHAP password” is “card”. If the user needs to change this
  setting during use, the setting must be changed according to the relevant information provided by the local operator.

• The default setting of “Dial Number” is “* 99 #”. If the user needs to change this setting
  during use, the setting must be changed according to the relevant information provided by
  the local operator.

• “Advanced settings” page are default settings, no need to change

• Click “LAN” in the menu bar, the “LAN Configuration” message is displayed on the right side of the page. The IP address and subnet mask are the default settings, and no change is required. As shown in Figure 14

Figure 14

• Click “Wireless Network” in the menu bar, and the message “Basic Wireless Network Settings” is displayed on the right side of the page. Users can understand the information of “device configuration” and “interface configuration”. The default setting of ESSID is “WiFi”, users can change the settings of ESSID according to their needs. No other content on this page needs to be changed. As shown in Figure 15

Figure 16

“Advanced settings” page are default settings, no need to change。

• Click “Wireless Security” in the menu bar, the wireless security related information is displayed on the right side of the page, “Encryption” and “Algorithm” are the default settings, no need to change. “Password” can be cancelled or set according to user needs, user-defined password, factory default settings without password. As shown in Figure 16

Figure 16

• Click “MAC-Filter” in the menu bar, the content displayed on the right side of the page is the default setting, no need to change.
• Click “Connected Site” in the menu bar, and the information about the connected terminal devices will be displayed on the right side of the page.
• Click “DHCP Server” in the menu bar, the “Basic Settings” and “DHCP List” are the default settings, no need to change.
• Click “Internet Control” in the menu bar, enter the URL to be filtered according to the prompt in the blank space on the right side of the page, and then click “Save & Apply”. Figure 17

Figure 17

If you use a third-party browser on a mobile device (mobile phone, tablet), you can filter some
URLs.

• Click “QoS Flow Control” in the menu bar. The content displayed on the right side of the page are the default settings. The data settings of “Download Speed” and “Upload Speed” have been verified to obtain a better Internet experience without modification. Figure 18

Figure 18

• Click “System Settings” in the menu bar, the right side of the page displays “System Time”
  information, users can complete the changes to the local time and time zone settings according to the country or region in “System Properties”, and click “Save & Apply” “. Other display content is the default setting, no need to change. As shown in Figure 19

Figure 19

• Click “Language” in the menu bar, and the language switching window will be displayed on the right side of the page. For the specific changing method, please refer to the contents of this manual: Item 3-Item 3 “Setting Instructions”-“b” About language switching instructions.
• Click “Administrative Rights” in the menu bar, the right side of the page displays the “Modify the administrator password to access the device” change window, users can change the administrator login password according to their needs, click “Save & Apply” after the change. Figure 20

Figure 20

• Click “Network Diagnosis”, enter the URL of the desired test on the right, and click the Ping button to check whether the network is connected and the speed of the network, which can help us analyze and determine whether there is a network failure. As shown in Figure 21

Figure 21

• When the user completes the above changes, click “Restart Device”, the “Execute Restart” button is displayed on the right side of the page. Click this button to complete the settings of the router, and then click “Exit” button to restore the login interface . Figure 22

Figure 22

In the settings of the router, most of the function settings are similar to ordinary routers. Just refer to the above operation instructions, you can successfully activate the router, and start your wireless journey now!

4. Common problems

4.1. Forgot router login account
Press and hold the reset button to restore the default factory settings. After restoring the settings, the web login address is [192.168.1.1:8088], and the login user name and password: root

4.2. Sometimes the WiFi signal is missing, which may be caused by the following conditions
a. When the device is moving, the SIM card is in poor contact. Turn off the power, reinsert and restart；
b. The SIM card does not select a standard large card, resulting in poor contact；
c. The device may not be within the coverage of the local mobile operator’s network；
d. Insufficient power of base station equipment in GSM network.

4.3. About upstream and downstream rates.
a. The communication module of this product is the Cat4 wireless communication module designed for the M2M and IoT fields by Shanghai Yiyuan Communication Technology Co., Ltd., a leading global supplier of wireless modules. Using 3GPP Rel. 11 technology, theoretically supports a maximum downlink rate of 150 Mbit / s and a maximum uplink rate of 50 Mbit / s. However, in actual applications, it may be restricted or restricted by factors such as the operator ’s base station equipment, operator ’s technology, and the router ’s “QoS flow control” function,
resulting in users not being able to play videos smoothly and quickly browse high-definition
pictures or GIF dynamic images.

b. But in practical applications, the important factors that affect the rate are as follows：

• Whether the system settings are correct
• Mobile terminal factor
• Base station hardware and transmission factor
• Base station radio frequency failure (RRU) or standing wave ratio alarm, base station antenna port partial failure, antenna port power imbalance
• GPS failure or clock synchronization failure
• Base station BBU baseband processing capacity is reduced
• DU software failure
• Transmission bandwidth limitation
• Wireless environmental impact (direct impact on SINR)
• Unreasonable power parameters prevent primary coverage, resulting in low SINR
• Overlay overlay
• Over coverage
• Weak indoor coverage
• Switching problem
• Internal interference
• External interference
• User behavior factor
• Other factors

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>