POWER PROBE TEMPKIT TEMPPROBE ADD-ON Wireless Temperature Probe Instruction Manual
- June 13, 2024
- POWER PROBE
Table of Contents
DUAL-ZONE DIGITAL
THERMOMETER
WITH WIRELESS REMOTE TEMPERATURE SENSOR
INTRODUCTION
o Thank you for purchasing the Power Probe TEMPKIT Dual Zone Thermometer with
Wireless Remote Temperature Sensor.
o Please read through this manual in it’s entirety to fully enjoy the benefits
and features of this product.
o The TEMPKIT has a built in temp sensor in the Base unit, plus a 2″ Remote
unit temp sensor that transmits the Remote unit temperature reading back to
the Base unit.
o The Remote temp sensor can transmit temperature readings up to 5 m (16.5
ft.) away from Base unit.
o Monitor temperature differences — Ambient vs. refrigeration outlet, Inside
vs. Outside Temperatures, and more.
o Use moveable clip to attach Remote to air vents or grilles to monitor outlet
temps.
o Please keep this manual for future reference.
FEATURES
o Dual Zone Readings
o Wireless Remote Sensor
o Opt. 2nd Remote Sensor
o Bright Backlit LCD
o °F and °C – Selectable
SPECIFICATIONS
o Operating Environment:
o Measuring Range:
o Accuracy:
o Wireless Range:
o Resolution:
o Battery Type:
(Lithium Batteries not recommended.)
-9°F to 158°F
(-22°C to 70°C)
-9°F to 158°F
(-22°C to 70°C)
+2.0°F (+2.0°C)
5m (16.5 ft) max.
0.1°
2 x AA and 2 x AAA
OPERATION
- Remove battery cover from rear of Base unit.
- Install two (2) AA batteries into battery cavity and replace battery cover.
- Press Base unit Power button for one sec. to turn ON/OFF.
- LCD display will show current temperature of Base unit Temp Sensor above the display.
- Remove battery cover from rear of Remote unit
- Install two (2) AAA batteries into battery cavity and replace battery cover.
- Slide Remote unit Power switch to the ON position. Indicator Light should flash.
- When paired, Remote unit temperature will display on Base unit second line.
- Press Backlight button to turn LCD backlight ON/OFF.
- Press °C/°F button to change the Base unit display reading from Fahrenheit to Celsius.
- Press the Remote Select button to select optional second Remote unit.
- If signal is lost, power the Base unit Off then On to reacquire.
WARRANTY
Power Probe Warranty
Power Probe products undergo a strict quality control inspection for
workmanship.
function, and safety before leaving the factory. From the date of purchase, we
will ‘warranty / repair Power Probe products for one (1) year against defects
in parts and ‘workmanship. All repairs due to misuse will be charged a fee not
o exceed the cost of the tool. All warranty units must be accompanied by a
copy of the original sales receipt. In the event of a malfunction or defective
unit, please call or email your Power Probe dealer.
FCC STATEMENT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired opera- tion.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>