RadioLink R8XM Compatible Transmitters Instruction Manual

June 4, 2024
RADioLink

RadioLink R8XM Compatible Transmitters Instruction Manual
RadioLink R8XM Compatible Transmitters

Introduction

Thanks for purchasing RadioLink 8-channel receiver R8XM. To fully enjoy the benefits of this product and ensure safety, please read the introduction carefully and set up the device as instructed steps.
If any problems found during the operation process, please kindly refer to the manual first. Thenyoucould contact our distributors to find solution or follow our Facebook homepage
https://www.facebook.com/radiolinkofficial to search related key words. Also you can send your questions to after_service@radioLink.com.cn and we will answer your question at the earliest.

Due to unforeseen changes in production procedures, the information contained in this manual is subject to change without notice.
For more information please check our website http://www.radiolink.com and follow our Facebook and You Tube homepage.

SAFETY PRECAUTIONS

  • Never operate your model during adverse weather conditions. Poor visibility can cause
    disorientation and loss of control of your model.

  • Never use this product in a crowd and illegal area.

  • Always ensure the trim levers at 0 and battery properly charged before connecting the receiver.

  • Always check all servos and their connections prior to each run.

  • Always be sure about turning off the receiver before the transmitter.

WARNING
This product is not a toy and is NOT suitable for children under the age of 14. Adults should keep the product out of the reach of children and exercise caution when operating this product in the presence of children.

Water or moisture may enter the transmitter inside through gaps in the antenna or joystick and cause model instability, even out of control. If running in the wet weather(such as game) is inevitable, always use plastic bags or waterproof cloth to cover the transmitter.

R8XM Introduction

RadioLink R8XM is a 2.4G 8 channels receiver with 4000 meters control distance, supportingsignal output of PPM and SBUS and is compatible with RadioLink transmitters T8FB(BT) / T8S(BT) / T8FB(OTG) / T8S(OTG) / RC6GS V3 / RC6GS V2 / RC6GS / RC4GS V3 / RC4GSV2 / RC4GS(must work with flight controller).
Product Overview

Binding

Each receiver has an individual ID code and must bind with transmitter before using. Whenthebinding is done, the ID code will be stored in the transmitter and there’s no need to rebind. Therefore, when a new R8XM is purchased, binding needs to be done in order to work with transmitter.
(Note: R8XM is not compatible with T8FB produced before December 2016)

Binding steps

  1. Put the receiver and the transmitter close to each other (about 50cm).
  2. Power on the transmitter and R8XM will bind to the closest transmitter automatically.
  3. Press the ID SET on the receiver’s side for more than 1s and the LED indicator will flash, meaning the binding process has begun.
  4. When the LED indicator stops flashing, binding is complete.
  5. Test the model servo to make sure it can be operated by the transmitter.

Note: When the transmitter and receiver are powered on, the LED indicator of R8XM flashes slowly means there is no binding or the receiver loses signal during flight.

Working Modes

There are two signal working modes of R8XM.
Purple LED, SBUS signal, 8 channels totally.
Red LED, PPM signal, 8 channels totally.

SBUS and PPM signal switch

Quick press the ID SET switch twice within 1 second, the signal is changed fromSBUStoPPM(or from PPM to SBUS).
The red LED indicates the PPM and purple LED indicates SBUS

Note of Antenna Installation

In order to maximize the signal transmission, it’s greatly advised that

  1. Keep antennas as straight as possible, or the effective control range will reduce.
  2. Big models may contain metal parts that influence signal emission. In this case. antennas should be positioned at both sides of the model to ensure the best signal status in all circumstances.
  3. Antennas should be kept away from metal conductor and carbon fiber at least half inch away and no over bending.
  4. Keep antennas away from motor, ESC or other possible interference sources.
  5. Sponge or foam material is advised to use to prevent vibration when installing receiver.
  6. Receiver contains some electronic components of high-precision. Be careful to avoid strongvibration and high temperature.
  7. Special vibration-proof material for R/C like foam or rubber cloth is used to pack to protect receiver. Keeping the receiver in a well sealed plastic bag can avoid humidity and dust, which would possibly make the receiver out of control.

When all the above steps are complete, please turn off the transmitter and re power on to test if the receiver is correctly bind with it.

Real-time Built-In Telemetry
R8XM supports real-time transmission of RSSI, receiver voltage, and model voltage. Thetelemetryrange is the same as the control range, 4000 meters.

Telemetry of RSSI and Receiver Voltage
RSSI and receiver voltage will be displayed after the successful binding between the transmitter andthe receiver.

Telemetry of Model Voltage
Connect the balance head of the battery to the telemetry port of R8XM, the model voltage will be displayed. There is no need for an external power battery voltage telemetry module, and R8XM supports up to 6S (25.2V) battery voltage telemetry.
Telemetry of Model Voltage

RSSI and Low Voltage Alarm Setting
When R8XM works with Radio Link T8FB/T8S (BT) transmitters, low voltage alarm can beset after connected to Parameter Setup APP on Android phone, iPhone or computer, so as to avoid the failure to return due to insufficient voltage during the flight. (The following is the setting page on Parameter Setup APP of iPhone)
RSSI and Low Voltage Alarm Setting

RSSI and Low Voltage Alarm Beeps
When the returned RSSI, receiver voltage, and model voltage are lower than the set alarmvalue, the transmitter will emit alarm tone:

  1. Low transmitter voltage alarm: keep DDDD beep quickly and continuously
  2. Low receiver voltage alarm: five DDDDD beeps as a unit continuous beeping prompt
  3. Low model voltage alarm: three DDD beeps as a unit continuous beeping prompt
  4. Low RSSI alarm: four DDDD beeps as a unit continuous beeping prompt.

Output RSSI Value from Receiver to FPV Monitor
Output RSSI Value from Receiver to FPV Monitor, and real-time RSSI Telemetry is available when Racing/Driving/Sailing.

  1. How to output RSSI value from receiver to FPV when the transmitter is T8S/T8FBand the flight controller is F4/F7?
    https://www.radiolink.com/newsinfo/504912.html?templateId=148964

  2. How to output RSSI value from receiver to FPV when the transmitter is T8FB/T8Sand the flight controller is Mini Pix/TURBO PiX/PIXHAWK?
    https://www.radiolink.com/newsinfo/504919.html?templateId=148964

R8XM Specifications

  • Model: R8XM

  • Dimension: 22*17mm (0.87”x0.67”)

  • Weight: 3g (4g with cable)

  • Antenna Length: 90mm

  • Channel Quantity: 8 channels

  • Operating Voltage: 3-6V DC

  • Operating Current: 40mA±5mA@5V

  • Signals: SBUS/PPM

  • Output Frequency: 2.4GHz ISM band(2400MHz~2483.5MHz)

  • Spread Spectrum: FHSS, 67 channels pseudo-random frequency hopping

  • Adaptable Models: Racing drone/Rotary Wing/Fixed wing/Glider/Multicopter/Car/Boat/Robot (must
    work with flight controller)

  • Control Distance: 4000 meters (2.49Miles) in the air (Maximum range tested in un obstructed areas free of interference and may vary depending on local regulations). Transmission: Telemetry of signal, RSSI, receiver voltage, model voltage ((The telemetry distanceis the same as the control distance)

  • Model Voltage Telemetry: 2S-6S LiPo battery (7.2V-25.2V)

  • Compatible Transmitter: T8FB(BT)/T8S(BT)/T8FB(OTG)/T8S(OTG)/RC6GS V3/RC6GSV2/RC6GS/RC4GS V3/RC4GS V2/RC4GS (must work with flight controller.

Thank you again for choosing Radio Link product.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals