Quay Design 99344 Hansen LED Wall Light Instruction Manual
- June 13, 2024
- QUAY DESIGN
Table of Contents
Quay Design 99344 Hansen LED Wall Light Instruction Manual
Wall Light
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Please keep these instructions for future reference.
Warnings!
This is a Class 1 product and must be earthed. Please read these instructions
carefully before commencing any work. It is recommended that this fitting is
installed by a qualified electrician.
Install in accordance with the IEE Wiring regulations and the Building
Regulations.To prevent electrocution switch off at mains supply before
installing or maintaining this fitting. Ensure other persons cannot restore
the electrical supply without your knowledge. If you are in any doubt, please
consult a qualified electrician.
This light fitting should be connected to a 5 amp fused circuit. If replacing
an existing fitting, make a note of the connections. Always use the correct
type and wattage bulb. Never exceed the wattage stated. When changing a bulb,
always switch off at the mains and allow the old bulb to cool down before
handling. Dispose of used bulbs carefully.
This product is suitable for indoor use only, on normal flammable surfaces.
Using a dimmer switch
This product is suitable for use with a dimmer switch. Please note, some
energy saver bulbs are not suitable for use with a dimmer switch.
Fixing Instructions
Make sure you have the following items which are required to install this
light fitting: Small electrical screwdriver, cross head screwdriver &
insulation tape.
Step 1
Before removing the existing fitting, carefully note the position of each set
of wires.
Step 2
Remove the fixing bracket (A) from the wall cover (see diagram in step 5) and
attach to the wall using the screws provided. Take care to avoid damaging any
concealed wiring and pipes.
Step 3
Having identified the household wiring from your existing light fitting,
connect to the connection block inside the product in the following way:
Check that…..
You have correctly identified the house wires. The connections are tight. No
loose strands have been left out of the connection block.
Step 4
When completed, ensure that there are no bare or loose strands of wire
exposed, and cover all exposed areas of the connection block with 2 layers of
insulation tape.
Step 5
Re-attach the product to the fixing strap by aligning the screw holes in the
wall back with the screw holes in the fixing bracket (A), then re-fit the
screws (B). Tighten the screws to secure. Take care not to trap any wiring.
Ensure the lampholder is correctly oriented and facing downwards.
Fitting/Replacing the bulb – Max. 40W E27 GLS
During use the bulb and light fitting get very hot. Switch off the product and allow the bulb to cool before changing the bulb. Avoid directly touching the bulbs as this will shorten their life. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting. If you use bulbs with a higher wattage the lamp holder could be damaged.
Step 6
Replace fuse or circuit breaker and switch on. Your light is now ready for use
Care and cleaning
Finish – We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish.
Safety Information
For your safety, always switch off the supply before changing lightbulbs, cleaning or removing shades. Always take care when handling glass parts and lightbulbs to avoid injury in case of breakage. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts be damaged or missing please access our website: www.poolelighting.com to request spare parts or please call our Product Helpline on (01202) 690945. We will despatch to you, within 7 working days, your missing/damaged part. When phoning please ensure you have the following information available: Name and Address, Daytime Telephone Number, Date of Purchase, Product Reference number or barcode number (inside ceiling cover or on box label), Description of Missing/Damaged Part. This does not affect your statutory rights.
Manufactured by: Poole Lighting Ltd.
UK: BH17 7BY
EU: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>