Quay Design 3012547 Chrystal Bathroom Flush Light Instruction Manual

: June 13, 2024
: QUAY DESIGN

Table of Contents

Quay Design 3012547 Chrystal Bathroom Flush Light
Product Information
Product Usage Instructions
Safety Warnings
Zone Information
Assembly/ User Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Quay Design 3012547 Chrystal Bathroom Flush Light

Product Information

The Flush Light Fitting is a lighting product designed for indoor use. It is suitable for connection to a 240v~50Hz power supply. The product complies with the British Standards BS 7671:2008 Requirements for Electrical Installations and must be installed according to the regulations outlined in the manual. For safety reasons, the product should only be used in areas that comply with the specified bathroom zones. These zones are defined in the BS 7671:2008 Standard and are as follows:

Zone 0: Directly above the bath or shower tray.
Zone 1: The area directly adjacent to and above Zone 0, up to a height of 2.25m.
Zone 2: The area extending 0.6m horizontally and 2.25m vertically from Zone 1.

The supply circuit must be protected by an RCD (Residual Current Device) or the casing of the light fitting must be connected to the Supplementary Equipotential Bonding points in the bathroom.

Product Usage Instructions

Before starting the installation, ensure that the product is fully assembled as illustrated in the manual.
The Light pack contains all the necessary components fo installation.
Gather the following tools that may be required for installation:
- Electric drill and assorted drill bits.
- Electrical insulation tape.
Refer to the assembly/user instructions provided below for step-by-step guidance:

Manufacturer Information
The Flush Light Fitting is manufactured by:

Poole Lighting Ltd., UK: BH17 7BY
Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg, EU

Safety Warnings

It is recommended that this light be installed by a qualified electrician in accordance with current IEE Wiring Regulations and Building Regulations ( Part P ).
This product is only suitable for connection to a 240v—50Hz supply and is for indoor use only.
This light may be installed in “Zones 1 and 2 and Outside Zones” of a bathroom where water jets are not used for cleaning purposes. These zones are referenced in BS 7671: 2008 “Requirements for Electrical Installations”, IEE Wiring Regulations 17th Edition. All dimensions must be checked in conjunction with the Regulations.
The supply circuit must be protected by an RCD OR the casing of the light must be connected to the “Supplementary Equipotential Bonding” points in the bathroom.
An electrician must be consulted if in any doubt about your own competency or meaning of bathroom “Zones” “Equipotential Bonding” or “RCD”
This fitting is a Class l, Earthed product. The Fitting must be connected to Earth.
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker before commencing installation.
Do not install a bulb with a greater wattage or different shape than specified on the label.
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product, and allow 10 minutes to cool before replacing adjusting, or cleaning.
If any modification is made it will invalidate the warranty and may render the product unsafe.
If the glass or diffuser is broken or cracked it must be replaced, please consult your retailer. This is the symbol which denotes this requirement:

Zone Information

The shower tray is shown; the bath has an equivalent diagram.
Refer to Standard for more information.
Basins should be regarded as having a 600mm Zone 2 hemisphere above and extending down to floor.

Assembly/ User Instructions

Before you start
Please read these instructions carefully before fitting and retain for reference. Check the packaging and make sure that you have all the required parts. Follow each assembly step in order to prevent incorrect assembly. Ensure that the product is fully assembled as illustrated before use.

The Light pack contains:

Light fitting.
Terminal connection block(s).
Fixing pack.

The following tools may be required:

Electric drill and assorted drill bits.
Electrical insulation tape.

These assembly diagrams are intended as a guide — if in doubt consult a qualified electrician.

Decide on the position of the light fitting / or remove the existing light fitting. Take note of the position of the electrical connections. Ensure there is a solid mounting surface, preferably a wooden joist or joist bridge to support the weight ot the light fitting.
Install the bulbs (1 ). Never fit a bulb with a higher wattage, as this could cause overheating and damage the fitting.
Fit the light cover (2), ensuring the seal is tight and being aware of cross-threading.
Remove the two side screws (5) and retain the screws for re-use. Use the fixing bracket as a template to mark the screw holes. Mark the screw holes and secure to the ceiling with appropriate screw fixings (3).
Support your fitting and connect the house wiring to the terminal block (4). When you are sure of the connections wrap the Terminal Block and overlap the wiring on both sides with 2 layers of insulation tape.
NOTE : This is a Class I fitting and must be earthed. Any loose terminal blocks not secured to the ceiling cup – should always be covered with 2 layers of good-quality insulation tape. Re-fit the back box ensuring no wires are damaged, trapped, or left exposed. Check the seal, use sealant if required
Secure the backplate over the bracket by using the screws (5) removed in Point 2.
Secure the shade (6) over the backplate.
Turn on the power and test.