genie WIPX2LBVLPR H.265 2MP ANPR Bullet Camera User Manual
- June 13, 2024
- GENIE
Table of Contents
WIPX2LBVLPR H.265 2MP ANPR Bullet Camera
Product Information:
-
Product Model: WIPX2LBVLPR
-
User Manual: Included
-
Safety Notes: Read carefully before operation
-
Power Supply: Listed Power Unit with ‘Limited Power Source’,
‘LPS’ marking -
Output Ratings: Minimum 12V/2A or POE 48V/350mA or AC24V
(depending on models) -
Altitude Limit: Maximum 2000m
-
Operating Temperature: Tma=60 Deg.C
-
PoE Function: ITE investigated to IEC 60950-1 standard,
suitable for PoE networks without routing to the outside plant -
Disassembly: Do not attempt to disassemble the camera
-
Cleaning: Use soft dry cloth or neutral detergent for
cleaning -
Avoid: Incorrect operation, shock vibration, heavy pressing,
aiming at extremely bright objects -
Installation: Follow the provided instructions, do not reverse
the camera -
Operating Conditions: Ensure temperature, humidity, and power
supply are within specified limits -
Heat Sources: Keep away from heat sources and direct airflow
from air conditioners -
Disclaimer: Use of internet access products at your own risk,
check local surveillance laws -
Regulatory Compliance: FCC Marking, CE Marking, RoHS Directive
compliance
Product Usage Instructions:
-
Read the user manual carefully before operating the unit.
-
Ensure the power supply is a Listed Power Unit with the
appropriate output ratings (12V/2A or POE 48V/350mA or AC24V). -
If using PoE function, connect the camera only to PoE networks
without routing to the outside plant. -
Do not disassemble the camera or remove screws or covers to
prevent electric shock. -
In case of failure, contact the nearest service center for
assistance. -
Avoid incorrect operation, shock vibration, heavy pressing that
can cause damage to the product. -
Clean the main body of the camera using a soft dry cloth or
neutral detergent if necessary. -
Avoid aiming the camera directly at extremely bright objects
like the sun to prevent damage to the image sensor. -
Follow the provided instructions for camera installation and
avoid reversing the camera. -
Ensure temperature, humidity, and power supply are within the
specified limits before operating the camera. -
Keep the camera away from heat sources and do not expose it to
direct airflow from an air conditioner. -
Use the product for surveillance purposes in compliance with
local surveillance laws.
2MP H.265 IP LPR Camera with 722mm Motorised Lens with 50m IR
WIPX2LBVLPR
User Manual
Please read these instructions carefully before operating the unit and keep
for further reference.
Notes on Safety
This product is intended to be supplied by a Listed Power Unit, marked with
‘Limited Power Source’, ‘LPS’ on unit, output rated minimum 12V/2 A or POE
48V/ 350mA or AC24V (depending on models), no more than 2000m altitude of
operation and Tma=60 Deg.C.
As for the modes with PoE function, the function of the ITE being investigated
to IEC 60950-1 standard is considered not likely to require connection to an
Ethernet network with outside plant routing, including campus environment and
the ITE is to be connected only to PoE networks without routing to the outside
plant.
Do not attempt to disassemble the camera; in order to prevent electric shock,
do not remove screws or covers.
There are no user-serviceable parts inside. Please contact the nearest service
center as soon as possible if there is any failure.
Avoid from incorrect operation, shock vibration, heavy pressing which can
cause damage to product.
Do not use corrosive detergent to clean main body of the camera. If necessary,
please use soft dry cloth to wipe dirt; for hard contamination, use neutral
detergent. Any cleanser for high grade furniture is applicable.
Avoid aiming the camera directly towards extremely bright objects, such as,
sun, as this may damage the image sensor.
Please follow the instructions to install the camera. Do not reverse the
camera, or the reversing image will be received.
Do not operate it in case temperature, humidity and power supply are beyond
the limited stipulations.
Keep away from heat sources such as radiators, heat registers, stove, etc. Do
not expose the product to the direct airflow from an air conditioner. This
manual is for using and managing the product. We may reserve the rights of
amending the typographical errors, inconsistencies with the latest version,
software upgrades and product improvements, interpretation and modification.
These changes will be published in the latest version without special
notification. All pictures, charts, images in this manual are only for
description and explanation of our products. The ownerships of trademarks,
logos and other intellectual properties related to Microsoft, Apple and Google
belong to the above-mentioned companies. This manual is suitable for ANPR
network cameras.
Disclaimer
With regard to the product with internet access, the use of product shall be
wholly at your own risks. Our company shall be irresponsible for abnormal
operation, privacy leakage or other damages resulting from cyber attack,
hacker attack, virus inspection, or other internet security risks; however,
Our company will provide timely technical support if necessary.
Surveillance laws vary from country to country. Check all laws in your local
region before using this product for surveillance purposes. We shall not take
the responsibility for any consequences resulting from illegal operations.
Regulatory Information
FCC Marking
The products have be tested and found in compliance with the council FCC rules
and regulations part 15 subpart B. Operation of this product is subject the
following two conditions: (1) this device may not cause harmful interface, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
CE Marking
The products have been manufactured to comply with the following directives.
EMC Directive 2014/30/EU
RoHS
The products have designed and manufactured in accordance with Directive EU
RoHS Directive 2011/65/EU and its amendment Directive EU 2015/863 on the
restriction of the use of certain hazardous substances in electrical and
electronic equipment.
Table of Contents
1 Introduction ……………………………………………………………………………………………………. 1
2 Network Connection ………………………………………………………………………………………… 2
2.1 LAN ……………………………………………………………………………………………………………………………… 2
2.1.1
Access through IP-Tool …………………………………………………………………………………….. 2
2.1.2
Directly Access through IE ………………………………………………………………………………… 4
2.2 WAN …………………………………………………………………………………………………………………………….. 5
3 Live View ………………………………………………………………………………………………………… 8
4 Network Camera Configuration……………………………………………………………………… 10
4.1 System Configuration…………………………………………………………………………………………………….. 10
4.1.1
Basic Information …………………………………………………………………………………………… 10
4.1.2
Date and Time ……………………………………………………………………………………………….. 10
4.1.3
Local Config………………………………………………………………………………………………….. 11
4.1.4
Storage………………………………………………………………………………………………………….. 11
4.2 Image Configuration ……………………………………………………………………………………………………… 14
4.2.1
Display Configuration …………………………………………………………………………………….. 14
4.2.2
Video / Audio Configuration ……………………………………………………………………………. 16
4.2.3
OSD Configuration…………………………………………………………………………………………. 17
4.2.4
Video Mask …………………………………………………………………………………………………… 18
4.2.5
ROI Configuration ………………………………………………………………………………………….. 19
4.2.6
Lens Control ………………………………………………………………………………………………….. 20
4.3 PTZ Configuration ………………………………………………………………………………………………………… 20
4.4 Alarm Configuration ……………………………………………………………………………………………………… 21
4.4.1
Motion Detection……………………………………………………………………………………………. 21
4.4.2
Other Alarms …………………………………………………………………………………………………. 22
4.4.3
Alarm In ……………………………………………………………………………………………………….. 24
4.4.4
Alarm Out……………………………………………………………………………………………………… 25
4.4.5
Alarm Server …………………………………………………………………………………………………. 26
4.5 Event Configuration ………………………………………………………………………………………………………. 26
4.5.1
Exception Settings ………………………………………………………………………………………….. 27
4.5.2
ANPR Settings ………………………………………………………………………………………………. 28
4.6 Network Configuration ………………………………………………………………………………………………….. 33
4.6.1
TCP/IP………………………………………………………………………………………………………….. 33
4.6.2
Port ………………………………………………………………………………………………………………. 35
4.6.3
Server Configuration ………………………………………………………………………………………. 35
4.6.4
DDNS …………………………………………………………………………………………………………… 35
4.6.5
SNMP…………………………………………………………………………………………………………… 37
4.6.6
802.1x…………………………………………………………………………………………………………… 38
4.6.7
RTSP ……………………………………………………………………………………………………………. 38
4.6.8
UPNP …………………………………………………………………………………………………………… 39
4.6.9
Email ……………………………………………………………………………………………………………. 39
Network Camera User Manual
4.6.10
FTP………………………………………………………………………………………………………………. 40
4.6.11
HTTPS………………………………………………………………………………………………………….. 41
4.6.12
P2P (Optional) ……………………………………………………………………………………………….. 42
4.6.13
QoS………………………………………………………………………………………………………………. 43
4.7 Security Configuration …………………………………………………………………………………………………… 43
4.7.1
User Configuration …………………………………………………………………………………………. 43
4.7.2
Online User …………………………………………………………………………………………………… 45
4.7.3
Block and Allow Lists …………………………………………………………………………………….. 45
4.7.4
Security Management ……………………………………………………………………………………… 45
4.8 Maintenance Configuration …………………………………………………………………………………………….. 46
4.8.1
Backup and Restore ………………………………………………………………………………………… 46
4.8.2
Reboot ………………………………………………………………………………………………………….. 47
4.8.3
Upgrade ………………………………………………………………………………………………………… 47
4.8.4
Operation Log………………………………………………………………………………………………… 47
5 Search …………………………………………………………………………………………………………… 49
5.1 Image Search………………………………………………………………………………………………………………… 49
5.2 Video Search ………………………………………………………………………………………………………………… 51
5.2.1
Local Video Search…………………………………………………………………………………………. 51
5.2.2
SD Card Video Search …………………………………………………………………………………….. 52
Appendix……………………………………………………………………………………………………………….. 54
Appendix 1 Troubleshooting …………………………………………………………………………………… 54
Appendix 2 Specifications ………………………………………………………………………………………. 56
Network Camera User Manual
1 Introduction
Main Features ICR auto switch, true day/night 3D DNR, WDR BLC, Defog, Anti-
flicker, smart IR, corridor mode ROI coding Abnormal video signal detection
(scene change, video blur detection, video color cast detection), license
plate recognition Support mobile surveillance by smart phones with iOS and
Android OS
Surveillance Application
1
Network Camera User Manual
2 Network Connection
Connect IP-Cam via LAN or WAN. Here only take IE browser for example. The
details are as follows:
2.1 LAN
In LAN, there are two ways to access IP-Cam: 1. access through IP-Tool; 2.
directly access through IE browser.
2.1.1 Access through IP-Tool
Network connection:
Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is installed in the PC from the CD. Double click the IP-Tool icon on the desktop to run this software as shown below:
Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the above table
to show the network information on the right hand. Modify the IP address and
gateway of the camera and make sure its network address is in the same local
network segment as the computer’s. Please modify the IP address of your device
according to the practical situation.
2
Network Camera User Manual
For example, the IP address of your computer is 192.168.1.4. So the IP address
of the camera shall be changed to 192.168.1.X. After modification, please
enter the password of the administrator and click the “Modify” button to
modify the setting.
The default password of the administrator is “123456”.
Double click the IP address and then the system will pop up the IE browser to
connect IP-CAM. Follow directions to download, install and run the Active X
control.
Enter the username and password in the login window to log in.
The default username is “admin”; the default password is “123456”.
3
Network Camera User Manual The system will pop up the above-mentioned textbox
to ask you to change the default password. It is strongly recommended to
change the default password for account security. If “Do not show again” is
checked, the textbox will not appear next time.
2.1.2 Directly Access through IE
The default network settings are as shown below: IP address: 192.168.226.201
Subnet Mask: 255.255.255.0 Gateway: 192.168.226.1 HTTP: 80 Data port: 9008 Use
the above default settings when logging in the camera for the first time.
Directly connect the camera to the computer through network cable.
Manually set the IP address of the PC and the network segment should be as the
same as the default settings of the IP camera. Open the network and share
center. Click “Local Area Connection” to pop up the following window.
Select “Properties” and then select internet protocol according to the actual
situation (for example: IPv4). Next, click the “Properties” button to set the
network of the PC.
4
Network Camera User Manual
Open the IE browser and enter the default address of IP-CAM and confirm.
Follow directions to download and install the Active X control. Enter the
default username and password in the login window and then enter to view.
2.2 WAN
Access through the router or virtual server
Make sure the camera is connected to the local network and then log in the
camera via LAN and go to ConfigNetworkPort menu to set the port number.
Port Setup
Go to Config NetworkTCP/IP menu to modify the IP address. 5
Network Camera User Manual
IP Setup
Go to the router’s management interface through IE browser to forward the IP
address and port of the camera in the “Virtual Server”.
Router Setup
Open the IE browser and enter its WAN IP and http port to access. (For
example, if the http port is changed to 81, please enter “192.198.1.201:81” in
the address bar of web browser to access). Access through PPPoE dial-up
Network connection
Access the camera through PPPoE auto dial-up. The setup steps are as follow:
Go to ConfigNetworkPort menu to set the port number.
6
Network Camera User Manual Go to Config NetworkTCP/IPPPPoE Config menu. Enable
PPPoE and then enter the user name and password from your internet service
provider.
Go to Config NetworkDDNS menu. Before configuring the DDNS, please apply for a
domain name first. Please refer to DDNS configuration for detail information.
Open the IE browser and enter the domain name and http port to access. Access
through static IP Network connection
The setup steps are as follow: Go to ConfigNetworkPort menu to set the port
number. Go to Config NetworkTCP/IP menu to set the IP address. Check “Use the
following IP address” and then enter the static IP address and other
parameters. Open the IE browser and enter its WAN IP and http port to access.
7
Network Camera User Manual After logging in, the following window will be shown.
3 Live View
The following table is the instructions of the icons on the live view interface.
Icon
Description
Icon
Description
Original size
Zoom out
Fit correct scale
Zoom/Focus control
Auto (fill the window)
SD card recording indicator
Full screen
Sensor alarm indicator
Start/stop live view
Start/stop two-way audio (only available for the model with audio input
connector)
Enable/disable audio
Motion alarm indicator Color abnormal indicator Abnormal clarity indicator
Snapshot
Scene change indicator
Start/stop local recording Zoom in
License plate detection
Those smart alarm indicators will flash only when the camera supports those
functions and the corresponding events are enabled. In full screen mode,
double click on the mouse to exit or press the ESC key on the keyboard. Click
AZ control button to show AZ control panel. The descriptions of the control
panel are as
8
Network Camera User Manual follows:
Icon
Description
Icon
Description
Zoom –
Zoom +
Focus –
Focus +
One key focus (used when image is out of focus after manual adjustment
9
Network Camera User Manual
4 Network Camera Configuration
In the Webcam client, choose “Config” to go to the configuration interface.
Note: Wherever applicable, click the “Save” button to save the settings.
4.1 System Configuration
4.1.1 Basic Information
In the “Basic Information” interface, the system information of the device is
listed.
Some versions may support device ID and QR code. If P2P is enabled (see
Network Configuration-P2P), the network camera can be quickly added to mobile
surveillance client, by scanning the QR code or entering device ID.
4.1.2 Date and Time
Go to ConfigSystemDate and Time. Please refer to the following interface.
10
Network Camera User Manual Select the time zone and DST as required. Click the
“Date and Time” tab to set the time mode.
4.1.3 Local Config
Go to ConfigSystemLocal Config to set up the storage path of captured pictures
and recorded videos on the local PC. There is also an option to enable or
disable the bitrate display in the recorded files.
Additionally, “Local smart snapshot storage” can be enabled or disabled here.
If enabled, the captured pictures triggered by smart events (like line
crossing detection, region intrusion, etc.) will be saved to the local PC.
4.1.4 Storage
Go to ConfigSystemStorage to go to the interface as shown below.
11
Network Camera User Manual SD Card Management Click the “Format” button to
format the SD card. All data will be cleared by clicking this button. Click
the “Eject” button to stop writing data to SD card. Then the SD card can be
ejected safely. Snapshot Quota: Set the capacity proportion of captured
pictures on the SD card. Video Quota: Set the capacity proportion of record
files on the SD card. Schedule Recording Settings 1. Go to
ConfigSystemStorageRecord to go to the interface as shown below.
2. Set record stream, pre-record time, cycle writing. Pre Record Time: Set
the time to record before the actual recording begins. 3. Set schedule
recording. Check “Enable Schedule Record” and set the schedule.
Weekly schedule 12
Network Camera User Manual Set the alarm time from Monday to Sunday for a
single week. Each day is divided in one hour increments. Green means
scheduled. Blank means unscheduled. “Add”: Add the schedule for a special day.
Drag the mouse to set the time on the timeline. “Erase”: Delete the schedule.
Drag the mouse to erase the time on the timeline. Manual Input: Click it for a
specific day to enter specific start and end times. This adds more
granularities (minutes). Day schedule Set the alarm time for alarm a special
day, such as a holiday. Note: Holiday schedule takes priority over weekly
schedule. Snapshot Settings Go to ConfigSystemStorageSnapshot to go to the
interface as shown below.
Set the format, resolution and quality of the image saved on the SD card and
the snapshot interval and quantity and the timing snapshot here. Snapshot
Quantity: The number you set here is the maximum quantity of snapshots. The
actual quantity of snapshots may be less than this number. Supposing the
occurrence time of an alarm event is less than the time of capturing pictures,
the actual quantity of snapshots is less than the set quantity of snapshots.
Timing Snapshot: Enable timing snapshot first and then set the snapshot
interval and schedule. The setup steps of schedule are the same as the
schedule recording (See Schedule Recording).
13
Network Camera User Manual
4.2 Image Configuration
Image Configuration includes Display, Video/Audio, OSD, Video Mask and ROI
Config.
4.2.1 Display Configuration
Go to ImageDisplay interface as shown below. The image’s brightness, contrast,
hue and saturation and so on for common, day and night mode can be set up
separately. The image effect can be quickly seen by switching the
configuration file.
Brightness: Set the brightness level of the camera’s image. Contrast: Set the
color difference between the brightest and darkest parts. Hue: Set the total
color degree of the image. Saturation: Set the degree of color purity. The
purer the color, the brighter the image is. Sharpness: Set the resolution
level of the image plane and the sharpness level of the image edge. Noise
Reduction: Decrease the noise and make the image more thorough. Increasing the
value will make the noise reduction effect better but it will reduce the image
resolution. Defog: Activating this function and setting an appropriate value
as needed in foggy, dusty, smoggy or rainy environment to get clear images.
14
Network Camera User Manual
Backlight Compensation (BLC): Off: disables the backlight compensation
function. It is the default mode. HWDR: WDR can adjust the camera to provide a
better image when there are both very bright and very dark areas
simultaneously in the field of the view by lowering the brightness of the
bright area and increasing the brightness of the dark area. Recording will be
stopped for a few seconds while the mode is changing from non-WDR to WDR mode.
HLC: lowers the brightness of the entire image by suppressing the brightness
of the image’s bright area and reducing the size of the halo area. BLC: If
enabled, the auto exposure will activate according to the scene so that the
object of the image in the darkest area will be seen clearly. HFR: High Frame
Rate. If “ON” is selected, the system will restart and then the maximum value
of the frame rate of the main stream can be set to 60 fps /50fps. Antiflicker:
Off: disables the anti-flicker function. This is used mostly in outdoor
installations. 50Hz: reduces flicker in 50Hz lighting conditions. 60Hz:
reduces flicker in 60Hz lighting conditions. Smart IR: Choose “ON” or “OFF”.
This function can effectively avoid image overexposure and underexposure by
controlling the brightness of the IR lights according to the actual conditions
to make the image more realistic. Please enable it as needed. White Balance:
Adjust the color temperature according to the environment automatically.
Frequency: 50Hz and 60Hz can be optional. Day/Night Mode: Choose “Auto”,
“Day”, “Night” or “Timing”. Infra-red Mode: Choose “Auto”, “ON” or “OFF”.
Exposure Mode: Choose “Auto” or “Manual”. If manual is chosen, the digital
shutter speed can be adjusted. Corridor Pattern: Corridor viewing modes can be
used for situations such as long hallways. 0, 90, 180 and 270 are available.
The default value is 0. The video resolution should be 1080P or below if this
function is used. Image Mirror: Turn the current video image horizontally.
Image Flip: Turn the current video image vertically.
Schedule Settings of Image Parameters: Click the “Schedule” tab as shown
below.
Set full time schedule for common, day, night mode and specified time schedule
for day and night. Choose “Schedule” in the drop-down box of schedule as shown
below.
15
Network Camera User Manual
Drag ” ” icons to set the time of day and night. Blue means day time and blank
means night time. If the current mode of camera parameters is set to schedule,
the image configuration mode will automatically switch between day and night
according to the schedule.
4.2.2 Video / Audio Configuration
Go to ImageVideo / Audio interface as shown below. In this interface, set the
resolution, frame rate, bitrate type, video quality and so on subject to the
actual network condition.
Click the “Audio” tab to go to the interface as shown below.
Three video streams can be adjustable. Resolution: The size of image. Frame
rate: The higher the frame rate, the video is smoother. Bitrate type: CBR and
VBR are optional. Bitrate is related to image quality. CBR means that no
matter how much change is seen in the video scene, the compression bitrate
will be kept constant. VBR means that the compression bitrate will be adjusted
according to scene changes. For example, for scenes that do not have much
movement, the bitrate will be kept at a lower value. This can help optimize
the network bandwidth usage. Bitrate: it can be adjusted when the mode is set
to CBR. The higher the bitrate, the better the image quality will be.
16
Network Camera User Manual
Video Quality: It can be adjusted when the mode is set to VBR. The higher the
image quality, the more bitrate will be required. I Frame interval: It
determines how many frames are allowed between a “group of pictures”. When a
new scene begins in a video, until that scene ends, the entire group of frames
(or pictures) can be considered as a group of pictures. If there is not much
movement in the scene, setting the value higher than the frame rate is fine,
potentially resulting in less bandwidth usage. However, if the value is set
too high, and there is a high frequency of movement in the video, there is a
risk of frame skipping. Video Compression: MJPEG, H264+, H264, H264S (Smart
H.264), H265, H265+ or H265S (Smart H.265) can be optional. MJPEG is not
available for main stream. If H.265/H.265+/ H.265S is chosen, make sure the
client system is able to decode H.265/H.265+/ H.265S. Compared to
H.265+/H.265, smart H.265 can spontaneously adjust the bitrate distribution
according to the requirements of the actual scene. For example, when there is
no human or vehicle detected, the bitrate will be automatically reduced with
no effect on image quality by using H.265S. Compared to H.265, H.265+ saves
more storage space with the same maximum bitrate in most scenes. Compared to
H.264, H.265 reduces the transmission bitrate under the same resolution, frame
rate and image quality. Profile: For H.264. Baseline, main and high profiles
are selectable. Send Snapshot: How many snapshots to generate for an event.
Video encode slice split: If this function is enabled, smooth image can be
gotten even though using the low-performance PC. Watermark: When playing back
the local recorded video in the search interface, the watermark can be
displayed. To enable it, check the watermark box and enter the watermark text.
Audio Encoding: G711A and G711U are selectable. Audio Type: LIN or MIC
optional. MIC type is available for the model with built-in MIC interface.
4.2.3 OSD Configuration
Go to ImageOSD interface as shown below.
Set time stamp, device name, OSD content and picture overlap here. After
enabling the corresponding display and entering the content, drag them to
change their position. Then click
17
Network Camera User Manual the “Save” button to save the settings.
Picture Overlap Settings: Check “OSD Content1”, choose “Picture Overlay” and
click “Browse” to select the overlap picture. Then click “Upload” to upload
the overlap picture. The pixel of the image shall not exceed 200*200, or it
cannot be uploaded.
4.2.4 Video Mask
Go to ImageVideo Mask interface as shown below. A maximum of 4 zones can be
set up.
To set up video mask: 1. Enable video mask. 2. Click the “Draw Area” button
and then drag the mouse to draw the video mask area. 3. Click the “Save”
button to save the settings. 4. Return to the live to verify that the area
have been drawn as shown as blocked out in the image.
18
Network Camera User Manual
To clear the video mask: Click the “Clear” button to delete the current video
mask area.
4.2.5 ROI Configuration
Go to ImageROI Config interface as shown below. An area in the image can be
set as a region of interest. This area will have a higher bitrate than the
rest of the image, resulting in better image quality for the identified area.
1. Check “Enable” and then click the “Draw Area” button. 2. Drag the mouse to
set the ROI area. 3. Set the level. 4. Click the “Save” button to save the
settings.
19
Network Camera User Manual
4.2.6 Lens Control
This function is only available for the model with motorized zoom lens. Within
this section, zoom and focus can be controlled. If the image is out of focus
after a manual adjustment, one key focus can be used to set the focus
automatically. Go to ConfigImage Zoom/Focus interface to set.
4.3 PTZ Configuration
This function is only available for the model with RS485 interface. It can be
used with a compatible external PTZ enclosure. Go to PTZProtocol interface as
shown below.
20
Network Camera User Manual
4.4 Alarm Configuration
4.4.1 Motion Detection
Go to AlarmMotion Detection to set motion detection alarm.
1. Check “Enable” check box to activate motion based alarms. If unchecked,
the camera will not send out any signals to trigger motion-based recording to
the NVR or CMS, even if there is motion in the video. Alarm Out: If selected,
this would trigger an external relay output that is connected to the camera on
detecting a motion based alarm. (For the models with two alarm output
interfaces, two alarm output can be selected.) Trigger Snap: If selected, the
system will capture images on motion detection and save the images on an SD
card. Trigger SD Recording: If selected, video will be recorded on an SD card
on motion detection. Trigger Email: If “Trigger Email” and “Attach Picture”
are checked (email address must be set first in the Email configuration
interface), the captured pictures and triggered event will be sent into those
addresses. Trigger FTP: If “Trigger FTP” and “Attach Picture” are checked, the
captured pictures will be sent into FTP server address. Please refer to FTP
configuration chapter for more details.
21
Network Camera User Manual 2. Set motion detection area and sensitivity. Click
the “Area and Sensitivity” tab to go to the interface as shown below.
Move the “Sensitivity” scroll bar to set the sensitivity. Higher sensitivity
value means that motion will be triggered more easily. Select “Add” and click
“Draw”. Drag the mouse to draw the motion detection area; Select “Erase” and
drag the mouse to clear motion detection area. After that, click the “Save” to
save the settings. 3. Set the schedule for motion detection. The schedule
setup steps of the motion detection are the same as the schedule recording
setup (See Schedule Recording).
4.4.2 Other Alarms
SD Card Full 1. Go to ConfigAlarmAnomalySD Card Full.
2. Click “Enable” and set the alarm holding time. 3. Set alarm trigger
options. The setup steps are the same as motion detection. Please refer to
motion detection chapter for details. SD Card Error When there are some errors
in writing SD card, the corresponding alarms will be triggered. 1. Go to
ConfigAlarmAnomalySD Card Error as shown below.
22
Network Camera User Manual
2. Click “Enable” and set the alarm holding time. 3. Set alarm trigger
options. Trigger alarm out, Email and FTP. The setup steps are the same as
motion detection. Please refer to motion detection chapter for details. IP
Address Conflict 1. Go to ConfigAlarmAnomalyIP Address Collision as shown
below.
2. Click “Enable alarm” and set the alarm holding time. 3. Trigger alarm out.
When the IP address of the camera is in conflict with the IP address of other
devices, the system will trigger the alarm out. Cable Disconnection 1. Go to
ConfigAlarmAnomalyCable Disconnected as shown below.
23
Network Camera User Manual 2. Click “Enable” and set the alarm holding time.
3. Trigger alarm out. When the camera is disconnected, the system will trigger
the alarm out.
4.4.3 Alarm In
To set sensor alarm (alarm in): Go to ConfigAlarmAlarm In interface as shown
below.
1. Click “Enable” and set the alarm type, alarm holding time and sensor name.
2. Set alarm trigger options. The setup steps are the same as motion
detection. Please refer to motion detection chapter for details. 3. Click
“Save” button to save the settings. 4. Set the schedule of the sensor alarm.
The setup steps of the schedule are the same as the schedule recording setup.
(See Schedule Recording). For the model with two alarm input interfaces, you
shall select the sensor ID first. Then set the relevant trigger items. Click
“Apply settings to” to quickly apply the settings to the other alarm input.
24
Network Camera User Manual
4.4.4 Alarm Out
This function is only available for some models. Go to ConfigAlarmAlarm Out.
Alarm Out ID: For the model with two alarm output interfaces, please select
the alarm out ID first as shown in the above left picture. Alarm Out Mode:
Alarm linkage, manual operation, day/night switch linkage and timing are
optional. Alarm Linkage: Having selected this mode, select alarm out name,
alarm holding time at the “Alarm Holding Time” pull down list box and alarm
type. Manual Operation: Having selected this mode, select the alarm type and
click “Open” to trigger the alarm out immediately; click “Close” to stop
alarm.
25
Network Camera User Manual Day/Night Switch Linkage: Having selected this
mode, select the alarm type and then choose to open or close alarm out when
the camera switches to day mode or night mode.
Timing: Select the alarm type. Then click “Add” and drag the mouse on the
timeline to set the schedule of alarm out; click “Erase” and drag the mouse on
the timeline to erase the set time schedule. After this schedule is saved, the
alarm out will be triggered in the specified time.
4.4.5 Alarm Server
Go to AlarmAlarm Server interface as shown below. Set the server address,
port, heartbeat and heartbeat interval. When an alarm occurs, the camera will
transfer the alarm event to the alarm server. If an alarm server is not
needed, there is no need to configure this section.
4.5 Event Configuration
For more accuracy, here are some recommendations for installation. Cameras
should be installed on stable surfaces, as vibrations can affect the accuracy
of
detection. Avoid pointing the camera at the reflective surfaces (like shiny
floors, mirrors, glass,
lake surfaces and so on). Do not aim the camera at the sun, road lamp or
headlights of the car. Avoid places that have too much shadowing.
26
Network Camera User Manual At any time of day or night, please make sure the
image of the camera is clear and with
adequate and even light, avoiding overexposure or too much darkness on both
sides.
4.5.1 Exception Settings
This function can detect changes in the surveillance environment affected by
the external factors. To set exception detection: Go to ConfigEventException
interface as shown below.
1. Enable the applicable detection that’s desired. Scene Change Detection:
Alarms will be triggered if the scene of the monitor video has changed. Video
Blur Detection: Alarms will be triggered if the video becomes blurry. Enable
Video Color Cast Detection: Alarms will be triggered if the video becomes
obscured. 2. Set the alarm holding time and alarm trigger options. The setup
steps are the same as motion detection. Please refer to motion detection
chapter for details. 3. Click “Save” button to save the settings. 4. Set the
sensitivity of the exception detection. Click “Sensitivity” tab to go to the
interface as shown below.
27
Network Camera User Manual
Drag the slider to set the sensitivity value or directly enter the sensitivity
value in the textbox. Click “Save” button to save the settings. The
sensitivity value of Scene Change Detection: The higher the value is, the more
sensitive the system responds to the amplitude of the scene change. The
sensitivity value of Video Blur Detection: The higher the value is, the more
sensitive the system responds to the blurriness of the image. The sensitivity
value of Video Color Cast Detection: The higher the value is, the more
sensitive the system responds to the obscuring of the image. The requirements
of camera and surrounding area 1. Auto-focusing function should not been
enabled for exception detection. 2. Try not to enable exception detection when
light changes greatly in the scene. 3. Please contact us for more detailed
application scenarios.
4.5.2 ANPR Settings
ANPR function is to detect and compare license plate numbers. Alarms will be
triggered when a license plate is detected. Vehicle license plate detection
and comparison settings: 1.Go to ConfigEventANPR as shown below.
2.Enable ANPR. 3.Set alarm holding time and alarm trigger options. The alarm
trigger setup steps are the same as motion detection setup. Please refer to
motion detection chapter for details. 4. Set the alarm detection area and the
blocked area.
28
Network Camera User Manual
To set the detection area: Click “Draw Area” and drag the border lines of the
rectangle to modify its size. Click “Stop Draw” to stop drawing the area.
Click “Clear” to clear the area. Then set the detectable size by defining the
maximum value and the minimum value (The default size range of a single number
plate image occupies from 5% to 50% of the entire image). To set the blocked
area Select the number of the undetected area. Then click “Draw Area” to draw
a closed area. Up to 4 areas can be set up. After you set the blocked area,
this area will not be detected.
5.Set the schedule of the ANPR. The setup steps of the schedule are the same
as schedule recording setup (See Schedule Recording). 6. Add vehicles to the
vehicle Database. Click the vehicle database tab to go to the following
interface.
29
Network Camera User Manual
Add vehicles Click “Add” to show a vehicle adding box as shown in the above
figure. Enter the license plate number, select list type, start and end time,
enter owner and license plate type. Then click “Save” to save the vehicle.
List type: unknown vehicle, allow list and block list can be selected. Click
“Bulk Entry” to add multiple vehicles at one time as shown below.
Please edit the vehicle information according to the requirements shown on the
above interface. If you don’t know how to edit the file, please click
“Download” to download an example file and then follow the example to edit.
After that, click “Browse” to choose the vehicle information file and click
“Upload” to import all vehicle information. Search vehicles After the vehicles
are added, you can search them in the vehicle list. Enter the license plate
number and list type and then click “Search” to search the added vehicle
information. Click “Modify” to modify its information. Click “Delete” to
delete this vehicle information. 7. Set the license plate comparison and alarm
linkage. Click the “Comparison and linkage” tab to go to the following
interface.
30
Network Camera User Manual
Set the fault tolerance, alarm list and check “alarm out”. Finally, click “Save” to save all the settings. Allow fault character(s) of the plate number: up to 2 characters are allowed. For example, if “2” is selected, the captured license plate will be matched successfully and trigger the corresponding alarm even if there are 2 characters (or less) of the captured license plate not matched with the license plate of the alarm list. Alarm list: Select a list as the comparison list. Allow list, block list or unknown vehicle can be optional. Alarm out: if enabled, the system will trigger alarm output when the captured license plate is matched successfully.
After all above information are set, go to the live interface and click pictures as shown below.
to see the captured
When the captured license plate is matched with the license plate of the
comparison list, the list type will be displayed under the license plate
number. Click the matched license plate
31
Network Camera User Manual picture, the matched details will pop up as shown
below.
Configuration requirements of camera and surrounding area The monitoring image
shall try to cover the lane, entering/exiting vehicles and these
vehicles’ plate number shall be always seen in the video. Try to avoid the
objects that will block the camera, such as pillars, obstacles, doors, etc.
Avoid the scenes with many trees or other moving objects (like humans, non-
motor
vehicles). The monitoring road shall be straight within 50 meters in front
of/behind the location of
the camera installation and make sure the camera points at the front or rear
of the vehicle. Crossroad monitoring: The installation height (H) shall range
from 4.5 m to 6m. The distance D (between the location of the camera
installation and the captured area) shall range from 15m to 25m. This distance
(D) depends on the installation height, usually 3 or 4 times as far as the
installation height (H). The distance of the captured area (L) shall be from
15m to 20m.
32
Network Camera User Manual The depression angle of the camera shall range from
10° to 15°. If the camera is installed on the side of the road, the pan angle
of the camera shall range
from 0° to 20°. If the camera is installed right above the middle of the road,
the pan angle of the camera
shall range from -10° to 10°. Entrance & Exit Monitoring The installation
height (H) shall range from 1.3 m to 1.5m. The distance D (between the
location of the camera installation and the captured area) shall range 2.5m to
3m. The distance of the captured area (L) shall be from 1.5m to 2m.
The depression angle of the camera shall range from 0° to 5°. The pan angle of
the camera shall range from 5° to 20°. The tilt angle of the license plate
After the camera is installed, you can log in the web client and view whether
the license plate tilts in the video. The tilt angle shall range from -5° to
5°.
If the captured license plate doesn’t meet the above requirement, you can
adjust the pan angle of the camera to correct it.
4.6 Network Configuration
4.6.1 TCP/IP
Go to ConfigNetworkTCP/IP interface as shown below. There are two ways for
network 33
Network Camera User Manual connection.
Use IP address (take IPv4 for example)-There are two options for IP setup:
obtain an IP address automatically by DHCP and use the following IP address.
Please choose one of the options as needed. Test: Test the effectiveness of
the IP address by clicking this button. Use PPPoE-Click the “PPPoE Config” tab
to go to the interface as shown below. Enable PPPoE and then enter the user
name and password from your ISP.
Either method of network connection can be used. If PPPoE is used to connect
internet, the camera will get a dynamic WAN IP address. This IP address will
change frequently. To be notified, the IP change notification function can be
used. Click “IP Change Notification Config” to go to the interface as shown
below.
Trigger Email: when the IP address of the device is changed, the new IP
address will be sent to the email address that has been set up. Trigger FTP:
when the IP address of the device is changed, the new IP address will be sent
to FTP server that has been set up.
34
Network Camera User Manual
4.6.2 Port
Go to ConfigNetworkPort interface as shown below. HTTP port, Data port and
RTSP port can be set.
HTTP Port: The default HTTP port is 80. It can be changed to any port which is
not occupied. HTTPS Port: The default HTTPs port is 443. It can be changed to
any port which is not occupied. Data Port: The default data port is 9008.
Please change it as necessary. RTSP Port: The default port is 554. Please
change it as necessary.
4.6.3 Server Configuration
This function is mainly used for connecting network video management system.
1. Check “Enable”. 2. Check the IP address and port of the transfer media
server in the ECMS/NVMS. Then enable the auto report in the ECMS/NVMS when
adding a new device. Next, enter the remaining information of the device in
the ECMS/NVMS. After that, the system will automatically allot a device ID.
Please check it in the ECMS/NVMS. 3. Enter the above-mentioned server address,
server port and device ID in the corresponding boxes. Click the “Save” button
to save the settings.
4.6.4 DDNS
If the camera is set up with a DHCP connection, DDNS should be set for the
internet. 1. Go to ConfigNetwork DDNS.
35
Network Camera User Manual
2. Apply for a domain name. Take www.dvrdyndns.com for example. Enter
www.dvrdydns.com in the IE address bar to visit its website. Then Click the
“Registration” button.
Create domain name. After the domain name is successfully applied for, the
domain name will be listed as below.
3. Enter the username, password, domain you apply for in the DDNS
configuration interface. 36
Network Camera User Manual 4. Click the “Save” button to save the settings.
4.6.5 SNMP
To get camera status, parameters and alarm information and remotely manage the
camera, the SNMP function can be used. Before using SNMP, please install an
SNMP management tool and set the parameters of the SNMP, such as SNMP port,
trap address. 1. Go to ConfigNetworkSNMP.
2. Check the corresponding version checkbox (Enable SNMPv1, Enable SNMPv2,
Enable SNMPv3) according to the version of the SNMP software that will be
used. 3. Set the values for “Read SNMP Community”, “Write SNMP Community”,
“Trap Address”, “Trap Port” and so on. Please make sure the settings are the
same as that of the SNMP software.
37
Network Camera User Manual Note: Please use the different version in
accordance with the security level you required. The higher the version is,
the higher the level of the security is.
4.6.6 802.1x
If it is enabled, the camera’s data can be protected. When the camera is
connected to the network protected by the IEE802.1x, user authentication is
needed.
To use this function, the camera shall be connected to a switch supporting
802.1x protocol. The switch can be reckoned as an authentication system to
identify the device in a local network. If the camera connected to the network
interface of the switch has passed the authentication of the switch, it can be
accessed via the local network. Protocol type and EAPOL version: Please use
the default settings. User name and password: The user name and password must
be the same with the user name and password applied for and registered in the
authentication server.
4.6.7 RTSP
Go to ConfigNetworkRTSP.
Select “Enable” to enable the RTSP function. Port: Access port of the
streaming media. The default number is 554. RTSP Address: The RTSP address
(unicast) format that can be used to play the stream in a media player.
38
Network Camera User Manual
Multicast Address Main stream: The address format is
“rtsp://IP address: rtsp port/profile1?transportmode=mcast”. Sub stream: The
address format is
“rtsp://IP address: rtsp port/profile2?transportmode=mcast”. Third stream: The
address format is
“rtsp://IP address: rtsp port/profile3?transportmode=mcast”. Audio: Having
entered the main/sub stream in a VLC player, the video and audio will play
automatically. If “Allow anonymous login…” is checked, there is no need to
enter the username and password to view the video. If “auto start” is enabled,
the multicast received data should be added into a VLC player to play the
video.
Note:1. This camera support local play through a VLC player. Enter the RTSP
address (unicast or multicast, eg.
rtsp://192.168.226.201:554/profile1?transportmode=mcast) in a VLC player to
realize the simultaneous play with the web client.
2. The IP address mentioned above cannot be the address of IPv6. 3. Avoid the
use of the same multicast address in the same local network. 4. When playing
the video through the multicast streams in a VLC player, please pay attention
to the mode of the VLC player. If it is set to TCP mode, the video cannot be
played. 5. If the coding format of the video of the main stream is MJPEG, the
video may be disordered at some resolutions.
4.6.8 UPNP
If this function is enabled, the camera can be quickly accessed through the
LAN. Go to ConfigNetworkUPnP. Enable UPNP and then enter UPnP name.
4.6.9 Email
If you need to trigger Email when an alarm happens or IP address is changed,
please set the Email here first. Go to ConfigNetwork Email.
39
Network Camera User Manual
Sender Address: sender’s e-mail address. User name and password: sender’s user
name and password. Server Address: The SMTP IP address or host name. Select
the secure connection type at the “Secure Connection” pull-down list according
to what’s required. SMTP Port: The SMTP port. Send Interval(S): The time
interval of sending email. For example, if it is set to 60 seconds and
multiple motion detection alarms are triggered within 60 seconds, they will be
considered as only one alarm event and only one email will be sent. If one
motion alarm event is triggered and then another motion detection alarm event
is triggered after 60 seconds, two emails will be sent. When different alarms
are triggered at the same time, multiple emails will be sent separately. Click
the “Test” button to test the connection of the account. Recipient Address:
receiver’s e-mail address.
4.6.10 FTP
After an FTP server is set up, captured pictures from events will be uploaded
to the FTP server. Go to ConfigNetwork FTP.
40
Network Camera User Manual
Server Name: The name of the FTP server. Server Address: The IP address or
domain name of the FTP. Upload Path: The directory where files will be
uploaded to. Port: The port of the FTP server. User Name and Password: The
username and password that are used to login to the FTP server.
4.6.11 HTTPS
HTTPs provides authentication of the web site and protects user privacy. Go to
Config NetworkHTTPS as shown below.
There is a certificate installed by default as shown above. Enable this
function and save it. Then the camera can be accessed by entering https://IP:
https port via the web browser (eg. https://192.168.226.201:443). A private
certificate can be created if users don’t want to use the default one. Click
“Delete” to cancel the default certificate. Then the following interface will
be displayed.
41
Network Camera User Manual
- If there is a signed certificate, click “Browse” to select it and then click “Install” to install it. Click “Create a private certificate” to enter the following creation interface.
Click the “Create” button to create a private certificate. Enter the country (only two letters available), domain (camera’s IP address/domain), validity date, password, province/state, region and so on. Then click “OK” to save the settings. Click “Create a certificate request” to enter the following interface.
Click “Create” to create the certificate request. Then download the certificate request and submit it to the trusted certificate authority for signature. After receiving the signed certificate, import the certificate to the device.
4.6.12 P2P (Optional)
If this function is enabled, the network camera can be quickly accessed by adding the device ID in mobile surveillance client or CMS/NVMS client via WAN. Enable this function by going to ConfigNetworkP2P interface.
42
Network Camera User Manual
4.6.13 QoS
QoS (Quality of Service) function is used to provide different quality of
services for different network applications. With the deficient bandwidth, the
router or switch will sort the data streams and transfer them according to
their priority to solve the network delay and network congestion by using this
function. Go to ConfigNetworkQoS.
Video/Audio DSCP: The range is from 0 to 63. Alarm DSCP: The range is from 0
to 63. Manager DSCP: The range is from 0 to 63. Generally speaking, the larger
the number is, the higher the priority is.
4.7 Security Configuration
4.7.1 User Configuration
Go to ConfigSecurityUser interface as shown below.
Add user: 1. Click the “Add” button to pop up the following textbox.
43
Network Camera User Manual
2. Enter user name in the “User Name” textbox. 3. Enter the password in the
“Password” and “Confirm Password” textbox. Please set the password according
to the requirement of the password security level (Go to
ConfigSecuritySecurity ManagementPassword Security interface to set the
security level). 4. Choose the user type. Administrator has all permissions.
Normal user can only view the live video. Advanced user has the same
permissions as an Administrator except for; user, backup settings, factory
reset, and upgrading the firmware. 5. Enter the MAC address of the PC in the
“Bind MAC” textbox. If this option is enabled, only the PC with the specified
MAC address can access the camera for that user. 6. Click the “OK” button and
then the newly added user will be displayed in the user list.
Modify user: 1. Select a user to modify password and MAC address if necessary
in the user configuration list box. 2. The “Edit user” dialog box pops up by
clicking the “Modify” button.
3. Enter the old password of the user in the “Old Password” text box. 4.
Enter the new password in the “New password” and “Confirm Password” text box.
5. Enter computer’s MAC address as necessary. 6. Click the “OK” button to save
the settings. Note: To change the access level of a user, the user must be
deleted and added again with the new access level. Delete user: 1. Select the
user to be deleted in the user configuration list box. 2. Click the “Delete”
button to delete the user. Note: The default administrator account cannot be
deleted.
44
Network Camera User Manual
4.7.2 Online User
Go to ConfigSecurityOnline User to view the user who is viewing the live
video.
An administrator user can kick out all the other users (including other
administrators).
4.7.3 Block and Allow Lists
Go to ConfigSecurityBlock and Allow Lists as shown below.
The setup steps are as follows: Check the “Enable address filtering” check
box. Select “Block/Allow the following address”, IPv4/IPv6/MAC and then enter
IP address or MAC address in the address box and click the “Add” button.
4.7.4 Security Management
Go to ConfigSecuritySecurity Management as shown below.
In order to prevent against malicious password unlocking, “locking once
illegal login” function can be enabled here. If this function is enabled,
login failure after trying six times will make the login interface locked. The
camera can be logged in again after a half hour or after the camera reboots.
For some specified versions, anonymous login with a private protocol can be
enabled here. If this function is enabled, enter
http://host:port/Anonymous/1[2/3] (eg. http://192.168.226.201:80/Anonymous/1)
via web browser to access the camera. 1 indicates main stream; 2 indicates sub
stream; 3 indicates third stream. Only video can be viewed by this means and
no other operations can be done. If no such function, please skip the
instruction.
45
Network Camera User Manual Password Security
Please set the password level and expiration time as needed. Password Level:
Weak, Medium or Strong. Weak level: Numbers, special characters, upper or
lower case letters can be used. You can choose one of them or any combination
of them when setting the password. Medium Level: 9~15 characters, including at
least two of the following categories: numbers, special characters, upper case
letters and lower case letters. Strong Level: 9~15 characters. Numbers,
special characters, upper case letters and lower case letters must be
included. For your account security, it is recommended to set a strong
password and change your password regularly.
4.8 Maintenance Configuration
4.8.1 Backup and Restore
Go to ConfigMaintenanceBackup & Restore.
46
Network Camera User Manual Import & Export Settings Configuration settings of
the camera can be exported form a camera into another camera. 1. Click
“Browse” to select the save path for import or export information on the PC.
2. Click the “Import Setting” or “Export Setting” button. Default Settings
Click the “Load Default” button to restore all system settings to the default
factory settings except those you want to keep.
4.8.2 Reboot
Go to ConfigMaintenanceReboot. Click the “Reboot” button to reboot the device.
Timed Reboot Setting: If necessary, the camera can be set up to reboot on a
time interval. Enable “Time Settings”, set the date and time and then click
the “Save” button to save the settings.
4.8.3 Upgrade
Go to ConfigMaintenanceUpgrade. In this interface, the camera firmware can be
updated.
1. Click the “Browse” button to select the save path of the upgrade file 2.
Click the “Upgrade” button to start upgrading the firmware. 3. The device will
restart automatically Caution! Do not close the browser or disconnect the
camera from the network during the upgrade.
4.8.4 Operation Log
To query and export log: 1. Go to ConfigMaintenanceOperation Log.
47
Network Camera User Manual 2. Select the main type, sub type, start and end
time. 3. Click “Search” to view the operation log. 4. Click “Export” to export
the operation log.
48
Network Camera User Manual
5 Search
5.1 Image Search
Click Search to go to the interface as shown below. Images that are saved on
the SD card can be found here.
Local Image Search 1. Choose “Picture”–“Local”. 2. Set time: Select date and choose the start and end time. 3. Click to search the images. 4. Double click a file name in the list to view the captured photos as shown below.
Click
to return to the previous interface. 49
Network Camera User Manual
SD Card Image Search 1. Choose “Picture”–“SD Card”.
2. Set time: Select date and choose the start and end time.
3. Choose the alarm events at the bottom of the interface.
4. Click to search the images.
5. Double click a file name in the list to view the captured photos.
Click
to return to the previous interface.
The descriptions of the buttons are shown as follows.
Icon
Description
Icon
Description
Close: Select an image and click this button to close the image.
Close all: Click this button to close all images.
Save: Click this button to select the path for saving the image on the PC.
Fit size: Click to fit the image on the screen.
Zoom in: Click this button to digitally zoom in.
Slide show play: Click this button to start the slide show mode.
Play speed: Play speed of the slide show.
Save all: Click this button to select the path for saving all pictures on the
PC.
Actual size: Click this button to display the actual size of the image.
Zoom out: Click this button to digitally zoom out.
Stop: Click this button to stop the slide show.
50
Network Camera User Manual
5.2 Video Search
5.2.1 Local Video Search
Click Search to go to the interface as shown below. Videos were recorded
locally to the PC can be played in this interface.
1. Choose “Record”–“Local”. 2. Set search time: Select the date and choose
the start and end time. 3. Click to search the images. 4. Double click on a
file name in the list to start playback.
51
Network Camera User Manual
Icon
Description
Icon
Description
Play button. After pausing the video, click this button to continue playing.
Pause button
Stop button
Speed down
Speed up
Watermark display
Enable / disable audio; drag the slider to adjust the volume after enabling audio.
5.2.2 SD Card Video Search
Click Search to go to the interface as shown below. Videos that were recorded
on the SD card can be played in this interface.
1. Choose “Record”–“SD Card”. 2. Set search time: Select the date and choose
the start and end time. 3. Click to search the images.
4. Select the alarm events at the bottom of the interface. 5. Select mix
stream (video and audio stream) or video stream as needed. 6. Double click on
a file name in the list to start playback.
52
Network Camera User Manual
The time table can be shown in 24H/12H/2H/1H format by clicking the corresponding
buttons.
Video clip and downloading
1. Search the video files according to the above mentioned steps.
2. Select the start time by clicking on the time table.
3. Click
to set the start time and then this button turns blue ( ).
4. Select the end time by clicking on the time table. Then click
to set the end time.
5. Click
to download the video file in the PC.
Click “Set up” to set the storage directory of the video files. Click “Open”
to play the video. Click “Clear List” to clear the downloading list. Click
“Close” to close the downloading window.
53
Network Camera User Manual
Appendix
Appendix 1 Troubleshooting
How to find the password? AReset the device to the default factory settings.
Default IP: 192.168.226.201; User name: admin; Password: 123456
Fail to connect devices through IE browser. A: Network is not well connected.
Check the connection and make sure it is connected well. B: IP address is not
available. Reset the IP address. C: Web port number has been changed: contact
administrator to get the correct port number. D: Exclude the above reasons.
Restore to default setting by IP-Tool.
IP tool cannot search devices. It may be caused by the anti-virus software in
your computer. Please exit it and try to search device again.
IE cannot download ActiveX control. A. IE browser may be set up to block
ActiveX. Follow the steps below. Open IE browser and then click
Tools—–Internet Options.
Select Security——Custom Level…. Enable all the options under “ActiveX controls
and plug-ins”. Click OK to finish setup. B. Other plug-ins or anti-virus
blocks ActiveX. Please uninstall or close them.
54
Network Camera User Manual
No sound can be heard. AAudio input device is not connected. Please connect
and try again. B: Audio function is not enabled at the corresponding channel.
Please enable this function.
55
Network Camera User Manual
Appendix 2 Specifications
Specification /Model
Camera
Image Sensor Image Size Electronic Shutter Iris Type Min. llumination Lens Mount Day&Night WDR Digital NR Video Compression H.264 Type Video Bit Rate Resolution
Image
Main Stream Sub Stream Third Stream
Image Settings
Interfaces
ROI Network Auido Reset RS485 Storage Alarm USB ABF Remote Monitoring Online Connection
Network Protocol
Interface Protocol Storage
Fucntion
Smart Alarm
Power Power Consumption Opterating Environment Dimension (mm) Weightnet
Installation
2MP ANPR Box Network Camera 1/2.8CMOS 1920×1080 1/25s~1/100000s DC Iris Color:
0.0026 lux@F1.2, AGC ON CS ICR 120dB 3D DNR
H.265S/H.265+/H.265/H.264S/H.264+/H.264/MJPEG Baseline profile/main
profile/high profile 64Kbps~6Mbps 1080P (1920×1080), 720P(1280×720), D1, CIF,
480×240 60Hz: 1080P/720P(1~30fps); 50Hz: 1080P/720P (1~25fps) HFR mode:
1080P/720P(1~60fps); 50Hz: 1080P/720P (1~50fps) 60Hz: 720P/D1/CIF/480×240
(1~30fps); 50Hz: 720P/D1/CIF/480×240 (1~25fps) 60Hz: CIF/ D1/480×240
(1~30fps); 50Hz: CIF/D1/ 480×240 (1~25fps) BLC, HLC, Defog, Saturation,
Brightness, Chroma, Contrast, Smart IR,Wide Dynamic, Sharpen, NR, etc.
adjustable through client or web browser Support RJ45 1CH audio input; 1CH
audio output; 1CH MIC IN Yes Yes Built-in micro SD card storage slot, up to
128 GB 2CH Alarm input; 2CH Alarm Ouput Yes Yes Web browser, CMS remote
control Support simultaneous monitoring for up to 10 users and multi-stream
transmission IPv4, IPv6, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP, SNMP,
HTTP, HTTPS, 802.1x, QoS ONVIF Network remote storage, micro SD card storage
Motion detection, Sensor detection, SD card Full, SD card error, IP address
conflict, cable disconnection, scene change detection, video blur detection,
video color cast detection, ANPR AC24V/DC12V/PoE < 6.5W
Temperature: -30°C~60°C; Relative Humidity: less than 95% (non-condensing)
146.9×79×64 Approx. 0.65KG
Wall mounting; ceiling mounting
56
Network Camera User Manual
Specification /Model
Image Sensor Image Size Electronic Shutter Iris Type
Min. llumination
Camera
Lens
Lens Mount Day&Night WDR Digital NR Angle Adjustment Video Compression H.264 Type Video Bit Rate Resolution
Image
Main Stream Sub Stream Third Stream
Image Settings
Interfaces
ROI Network Auido Reset Storage Alarm Remote Monitoring Online Connection
Fucntion
Network Protocol Interface Protocol Storage
Smart Alarm
Others
IR Distance Protection Grade Power Power Consumption Opterating Environment
Dimension (mm)
Weightnet Installation
2MP ANPR Bullet Network Camera 1/2.8CMOS 1920×1080 1/25s~1/100000s DC Iris
0.0026lux@F1.2, AGC ON; 0 lux with IR; 0.005 lux@F1.4, AGC ON; 0 lux with IR
2.8~12mm@F1.4, (motorized), horizontal field of view:103.4°~32.4° 7~22mm@F1.4,
(motorized), horizontal field of view:44°~17.6° Ø14 ICR 120dB 3D DNR Pan:
0°~360°; Tilt 0°~90°; Rotation:0°~360°
H.265S/H.265+/H.265/H.264S/H.264+/H.264/MJPEG Baseline profile/main
profile/high profile 64Kbps~6Mbps 1080P (1920×1080), 720P(1280×720), D1, CIF,
480×240 60Hz: 1080P/720P(1~30fps); 50Hz: 1080P/720P (1~25fps) HFR mode:
1080P/720P(1~60fps); 50Hz: 1080P/720P (1~50fps) 60Hz: 720P/D1/CIF/480×240
(1~30fps); 50Hz: 720P/D1/CIF/480×240 (1~25fps) 60Hz: CIF/ D1/480×240
(1~30fps); 50Hz: CIF/D1/ 480×240 (1~25fps) BLC, HLC, Defog, Saturation,
Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser Support RJ45 1CH audio input; 1CH audio output
Yes Built-in micro SD card storage slot, up to 128 GB 1CH Alarm input; 1CH
Alarm Ouput Web browser, CMS remote control Support simultaneous monitoring
for up to 10 users and multi-stream transmission IPv4, IPv6, UDP, DHCP, NTP,
RTSP, PPPoE, DDNS, SMTP, FTP, SNMP, HTTP, HTTPS, 802.1x, QoS ONVIF Network
remote storage, micro SD card storage Motion detection, Sensor detection, SD
card Full, SD card error, IP address conflict, cable disconnection, scene
change detection, video blur detection, video color cast detection, ANPR 50~70
m or 70~100m optional IP67 DC12V/PoE < 11W
Temperature: -30°C~60°C; Relative Humidity: less than 95% (non-condensing)
279.5×100.3×88.9
Approx. 1.1KG
Wall mounting; ceiling mounting
57
Sales +44(0)1707 330541 Enquiries sales@genieproducts.co.uk Website www.genieproducts.co.uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>