genie WIP2PTZ25P 2MP H.265 IP IR 4 Inch 25x Optical Zoom PTZ Camera User Guide

: June 13, 2024
: GENIE

Table of Contents

genie WIP2PTZ25P 2MP H.265 IP IR 4 Inch 25x Optical Zoom PTZ Camera
Intro Section
Introduction
Product Features
Product Dimensions
Specification
Overview
Cable Connection
Connecting Network Cable
Installation
Network Connection
Preset Description
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

genie WIP2PTZ25P 2MP H.265 IP IR 4 Inch 25x Optical Zoom PTZ Camera

Please read these instructions carefully before operating the unit and keep them for further reference.

Intro Section

Please read this instruction carefully before operating the product and keep it for further reference. All examples and pictures used here are for reference only. The contents of this manual are subject to change without notice.

CAUTION

If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the camera yourself. We shall not be responsible for any problems caused by unauthorized repair or maintenance.
Do not allow water or liquid into the camera while in use.
When using the product, you must be in strict compliance with the electrical safety regulations of the nation and region.
When the product is mounted on a wall or ceiling, the device needs to be firmly fixed.
Make sure the power supply voltage is correct before using the camera.
Do not drop the camera or subject it to any physical shock.
If cleaning, please use a clean soft cloth with a little neutral detergent to wipe it gently.
Do not aim the camera at the sun or in any area where there is bright lighting.
The device may be burned out by a laser beam, so when any laser equipment is in use, make sure that the surface of the device will not be exposed to the laser beam.
Do not place the camera in extremely hot, cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for the operating environment.

Introduction

The Genie WIP2PTZ25P is a powerful PTZ camera with accurate pan, tilt and zoom performance. The camera provides a wide monitoring range as well as a full 2MP high definition resolution at 25/30fps. The camera is rated IP66 which means it works well outdoors with effective protection against lightning. The camera also features AI functions such as face recognition, face comparison, and tracking.

Product Features

Face recognition
Face comparison
Target counting
Alarm triggering by human or vehicle
Smart human or vehicle tracking, manual tracking, auto-tracking (via software setting)
1/2.8″ progressive scan CMOS
Up to 1920×1080 resolution
Minimum illumination: Colour: 0.005 lux @ (F1.6 AGC ON) B&W: 0.001 lux@ (F1.6 AGC ON) 0 Lux with IR
25x optical zoom, 16x digital zoom
120 dB WDR, 3D DNR, Smart IR
Smart IR with a distance of 150m
IP66 ingress protection
Smart TM 1.0 (Thermal Management)
Up to 150m IR distance
Smart H.265/H.264 video compression
0.5Tops Deep-learning Engine
Smart tracking of human/vehicle
Smart detection and perimeter protection
IP66,-30°C~55°C, ADC12 + PC/GF
PoE+ (802.3.at, class 3) and DC12V
API and SDK
Requires WPTZWB bracket

Product Dimensions

Specification

Camera

| Image Sensor| 1/2.8″progressive scan CMOS
---|---|---
Minimum Illumination| Colour: 0.005 Lux @ (F1.65, AGC ON),

B&W: 0.001Lux @(F1.65, AGC ON) 0 Lux with IR

Picture Overlay

| Logo picture could be overlaid on video with 128×128pixels,24bits BMP format

Lens

| Focus Length| f=4.8–120mm lens,25x optical
Zoom Speed| Approx. 3.6s (optical zoom, widetele)

Field of View

| Horizontal:57.6° to 2.5°(wide-tele) Vertical: 34.4° to 1.4°(wide-tele) Diagonal: 64.5° to 2.9°(wide-tele)
Working Distance| Wide: 1.0m ~ INF, Tele: 1.5m ~ INF
Aperture Range| F1.65 ~ F3.8 (Wide-tele)

Compression Standard

| 8 cruises, up to 16 presets for each cruises
Trace| 4 traces, record time over 3 minutes for each trace
Power Off Memory| Support
Action Mode| Preset/Cruise/Track/Auto Scan/Random Scan
3D Positioning| Support
PTZ Position Display| Support
Schedule Task| Preset / Cruise / Track / Random Scan / Boundary Scanning

/ Dome reboot

Network

| Maximum Resolution| 1920×1080
---|---|---
Main Stream| 1920×1080, 1280×720 25/30fps
Sub Stream| 25fps (720p, 704×576, 352×288)

30fps (720p, 704×480, 352×240)

Third Stream| 25fps (704×576, 640×480, 352×288)

30fps (704×480, 640×480, 352×240)

SVC| Yes
Video Compression| H.265/H.264/MJPEG
Audio Enhancement| No

Protocols

| HTTP, HTTPS, IPv4/IPv6, 802.1x, QoS, FTP, SMTP, UPnP, SNMP,DNS, DDNS, NTP, RTSP, RTCP, RTP, TCP/IP, UDP, IGMP, ICMP,DHCP, PPPoE
Simultaneous Live View| Up to 6 channels
User / Host| Up to 16 users, 3 levels: Administrator, Advanced User and Normal User

Security Measures

| User authentication (ID and PW), Host authentication (MAC address); HTTPS encryption, IEEE802.1x port-based network access control, IP address filtering

Smart Features

Smart Detection

| Intrusion detection, Line crossing detection, Region entrance detection, Region exiting detection, Scene change detection, target counting, Support alarm triggering by human or vehicle, filtering flag/animal.
Smart Tracking| Manual Tracking, Auto Tracking (human or vehicle by software setting)

System Integration

| Alarm Interface| None
Audio Interface| None
Alarm Linkage| Alarm actions, Memory Card Video Record, Trigger Recording, Upload to FTP/Memory Card, Send Email, etc.
Network Interface| 1x RJ45 10M/100M Adaptive Ethernet (Support PoE 802.3.at)
CVBS| None
RS485| None
Storage| On-Body memory card slot, support microSD/SDHC/SDXC, up to 256G
API| Onvif compatible, support TVT SDK and 3rd party management platform
Client| N9000 1.4.5, NVMS 2.0; and 3rd party client
Web Browser| IE8–11, Chrome41.0–44, Firefox30.0–51, Safari8.0–11

IR

| IR Distance| 150m
Smart IR| Yes

Others

| Power| DC12V or PoE+ (802.3.at, class 3), (Max 22W, include IR on, Heater on, Fan working)
Working Conditions| -30°C ~ 55°C (-22°F ~ 131°F), 90%RH less (

non-condensing), Cold start at – 20°C

Overview

Ethernet Connector
Power Connector
Safety Wire

Cable Connection

genie-WIP2PTZ25P-2MP-H.265-IP-IR-4-Inch-25x-Optical-Zoom-PTZ-Camera-
FIG-3

Connecting Network Cable

genie-WIP2PTZ25P-2MP-H.265-IP-IR-4-Inch-25x-Optical-Zoom-PTZ-Camera-
FIG-4

Loosen the nut from the main element.
Run the network cable (without RJ 45 connector) through both elements. Then crimp the cable with RJ 45 connector.
Connect the cable to the hermetic connector. Then tighten the nut and the main cover.

Installation

Micro SD Card Installation
This PTZ camera supports wall or ceiling mounting. Please select a way to install as needed. Also, please make sure the wall is strong enough to bear the dome camera’s weigh and the camera is powered off during installation. The following instructions are for reference only.

Loosen the four screws of the cover and then remove the cover.
Insert a micro SD card as indicated below and then install the cover back.

Wall Mount Installation

Pull the cables through the bracket.
Secure the PTZ camera to the bracket with screws.
Drill the screw holes on the wall according to the drill template. Then insert the plastic plugs into the holes.
Drill the screw holes on the wall according to the drill template. Then insert the plastic plugs into the holes.
Connect the cables and then hang the bracket on the wall.
Attach the bracket to the wall with four screws.

Ceiling Mount Installation

Install the ceiling mounting bracket according to the following diagram.
Mount the adapter tube to the bracket and secure it with a screw. Adapter Tube
Secure the ceiling mounting bracket to the ceiling.
Connect cables and then hook the safety wire to the adapter tube.
Fasten the PTZ camera to the adapter tube with screws firmly.

Network Connection

Access the Camera through the IP Tool

Make sure that the camera and the PC are well connected via LAN.
Find the IP Tool from the CD and then install it on the computer. After that, run the IP Tool as shown below.
Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right hand. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as that of the computer. Please modify the IP address of your device according to the practical situation.
For example, the IP address of your computer is 192.168.1.4. So the IP address of the camera shall be changed to 192.168.1.X and the gateway shall be changed to 192.168.1.1. After modification, please enter the password of the administrator and click the “Modify” button to modify the settings. The default password of the administrator is “123456”.
Double-click the camera listed in the IP Tool or manually enter the IP address in the address bar of the web browser to connect to the PTZ. Then follow the directions to download and install the plugin. Enter the username and password in the login interface. The default username is admin; the default password is 123456.

Preset Description

Call Preset

| Call No. 90 Preset| Run track 1
---|---|---
Call No. 91 Preset| Run cruise 1
Call No. 92 Preset| Run cruise 2
Call No. 93 Preset| Run cruise 3
Call No. 94 Preset| Run cruise 4
Call No. 95 Preset| OSD menu
Call No. 97 Preset| Enable random scan
Call No. 99 Preset| Enable P-PSCAN

Set Preset

| Set No. 91 Preset| Set random scan(start scanning from preset 91)
Set No. 92 Preset| Set left border of P-PSCAN
Set No. 93 Preset| Set right border of P-PSCAN

Sales +44(0)1707 330541
Inquiries sales@genieproducts.co.uk
Website www.genieproducts.co.uk