GROWATT 044.SK0000500 Shine WiFi-F European Distributor User Guide

GROWATT 044.SK0000500 Shine WiFi-F European Distributor User Guide

Connection between inverter and ShineWiFi module

Plug cubeWiFi into the WiFi/GPRS port

Turn on inverter and check ShineWiFi state

After install the ShineWiFi module, turn on the inverter, red LED flashing indicates the inverter and ShineWiFi communication is normal.

communication is OK

Registration and adding device

Scan the QR code below to download ShinePhone, also you search ShinePhone in iOS or Google Play Store, install it. can download and Registration and adding device

Note:

1. Make sure you download the latest version

2. For further information please visit server.growatt.com
   

3. Connect your mobile phone to the WiFi of your home which the ShineWiFi module will be connected.

4. The router name should consist with English letters numbers, it does not support special symbols.

5. For safety reason, please use an encrypted wireless network

6. It does not support a public network that uses a secondary authentication.

7. It does not support bridge network.

8. Open ShinePhone APP, click “Register” on login page.
   

9. Select country and city, then click “Next” enter next page.
   Note: If you select a wrong country and city, the system time maybe wrong.

10. Fill out the required information, then click “Next”, it will guide you to the “Add datalogger” page
    

11. . Scan or input the ShineWiFi barcode and checkcode,then click “Register”, it will move you to the “Set ShineWifi” page
    

12. Fill out the wifi network and password, then click“Configuration”, after successful configuration, a note will pop up “Configured successfully”, then it will move to the “my plant” page.
    Note: There are 3 LEDs on ShineWiFi, only the blue LED flashing indicates the ShineWiFi module is successfully connected to the router and Growatt Shine Server.
    

13. If the pop up a message says “Failed”, please refer to Appendix A of the troubleshooting guide to solve the problem. After that, login to your account and click the “+” sign on the right top side of the page, and select“Datalogger list”in the appearing dialog window. Push on the datalogger’s serial number for 3 sec, until a small dialog window appears,select “Configure datalogger”. It will move to the “Set ShineWifi”page,enter the home routers name and password, then click, “Set” the connection configuration process will begin.
    

14. After successful configuration, it will move to the plant” page, select the inverter in the device list to inverter update information.
    

15. f you want to add/edit/delete/configure a datalogger, click the “+” sign on the right top side “my plant” page. There are 4 options in the dialog window when push on the datalogger’s click the one you need. Add datalogger” is for adding a new ShineWiFi module to this account.

16. Edit datalogger” is used to assign an alias name for your ShineWiFi module.

17. Delete datalogger” is used to remove the ShineWiFi module from this account.

18. Configure datalogger” is used for configuring the connection of the ShineWiFi module to of the serial number, router.

Reset ShineWiFi to Factory Settings

When you have changed your home router password, or changed to you need to reset ShineWiFi to factory settings and rubber plug, and press the KEY button up, then login to your long press this a new router, reconfigure it. Remove the for 6 sec, until all three LEDs long light ShinePhone account, click the “+”on right top of this page, datalogger serial number to reconfigure.

Appendix A: ShineWiFi KEY Button Description

When ShineWiFi is powered on, remove the rubber plug, and press the KEY button. (ShineWiFi LED will change from flash to always ON)| ShineWiFi will enter to AP mode. AP mode is a debug mode, only allowed for professional
When ShineWiFi in AP mode, press The KEY button of ShineWiFi (ShineWiFi LED will change from always ON to flash)| Quit AP mode
Long press the KEY button for More than 6 sec (ShineWiFi All LEDs always ON)| **** Reset ShineWiFi to Factory settings

Troubleshooting

1. Check if the DIP switch beside inverters WiFi/GPRS port is switched DIP1 to “ON”

**** After configuration, only Red LED flashes| **** ShineWiFi can′t connect to the home router|

1. Check router information a)   Router name should consist of English letters and numbers, it does not support special symbolsb)   For safety reason, please use encrypted wireless networkc)   It does not support public network that use secondary authentication
2. Check if you filled in the correct name and password of the home router when configuring it

**** After configuration, Only Green LED flashes| ShineWiFi already connected to the home router, but not connectedTo Growatt ShineServer|

1. Check if home router is connected to the internet
2. Check if the router firewall allows to select port 5279 and 5280

After configuration, Only Blue LED flashes| ShineWiFi communication OK with inverter, home router, and Growatt ShineServer| **** Normal working state
Red LED always ON| ShineWiFi module error| Need to replace with a new ShineWiFi
Green LED always ON| ShineWiFi module in switching mode| No response if you press the KEY button during this period
Blue LED always ON| ShineWiFi module is in AP mode| Debug mode, short press the KEY button to quit

For more info, please download from
http://server.growatt.com
+86 755 2747 1942 F +86 755 2747 2131
E service@ginverter.com
W www.ginverter.com

References

• Growatt | Global Leading Distributed Energy Solution Provider
• Login

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>