SHENZHEN SHENGLAI TECHNOLOGY CO LIMITED UPTBH Wireless Headphone Instruction Manual
- June 13, 2024
- SHENZHEN SHENGLAI TECHNOLOGY CO LIMITED
Table of Contents
SHENGLAI TECHNOLOGY CO LIMITED
UPTBH Wireless Headphone
Instruction Manual
UPTBH Wireless Headphone
INSTRUCTIONS
Thank you for purchasing the UPTECH Wireless Headphones. Please take the time to read this manual carefully, even if you are already familiar with a similar product. In addition, please store this guide for future reference.
SPECIFICATIONS
Battery Capacity: Li-Lon Battery 150mAh
Size of the speaker. 40 mm
Impedance: 32 Ohm
Use Distance: 33 Feet / 10 Meters
Playing time: Shh
Charging Time: Approximately 2H
Charge Type: Type-C
BASIC INSTRUCTIONS
To turn headphones on, press and hold the Power button, you will hear an indication tone, and the blue and red LEDs, located next to the Aux port, lights will flash rapidly. The blue LED will flash intermittently when the device is paired and playing music. To turn the headphones off, press and hold the Power button.
CHARGING THE DEVICE
Plug the Type-C end of the charging cable into the port on the headphones.
Plug the USB end into a computer’s USB port or a compatible DC 5V 500mA wall
adapter (only use the supplied cable). The red LED will turn on to indicate
the device is charging. Once fully charged, the LEO will tum off. When the
battery is low, approximately 2 hours are needed to charge the headphone’s
battery.
Note: Overcharging could reduce the life of the battery. A charged
battery will lose its capacity if it is not used on a regular basis.
PAIRING THE DEVICE
Place headphones within 33ft/10 meters of a Bluetooth-enabled device.
Turn the headphones on, and you will hear an indication tone, and the blue and
red LED light will flash rapidly. On your device’s Bluetooth menu, find and
select Ombre BT Headphone” (you may be required to enter a password “0000”).
Once paired successfully, you will hear another Indication tone, and the blue
LEO light will flash Intermittently while on and playing music.
AUX IN MODE
Insert a 3.5mm AUX cable into the Aux input of the headphone, and the other
end of the cable to the audio device.
Note: While using this device In Aux-in mode, you do not need to power on
the headphones, and all audio controls on the headphones are disabled. All
audio is controlled via the connected device.
HEADPHONE BUTTON
LAYOUT AND FUNCTIONS
HEADPHONE CONTROLS
Volume Increase / Next Track Button
Press repeatedly to incrementally increase the volume a tone will play when
the maximum volume has been reached. Press and hold for the next track.
On-Off I Play-Pause/ Call Answer Button
Press and hold to power on/off. Short press to pause the track, and press
again to resume play. Press to answer and end incoming calls, press and hold
to reject a call, and short press twice to redial the last call.
Volume Decrease/ Last Track Button
Press repeatedly to incrementally decrease the volume. Press and hold for the
previous track.
HEADPHONE PORTS
TYPE-C PORT
DC 5V: Use the included Type-C USB Cable to connect this device to a
computer’s USB port or a compatible AC power adapter with USB to charge.
AUXILIARY CABLE PORT
Use the 3.5mm AUX audio cable to connect the headphone to your non-Bluetooth-
enabled mobile phone/MP3 player/PC/laptop and select the appropriate mode to
play media.
SAFETY INFORMATION
Do not attempt to disassemble the device. Doing so may result in an electric
shock.
Do not use this device on an aircraft or in a hospital.
Do not expose this device to direct sunlight, heat, or open flame.
The device may become warm while charging.
CAUTION
Any changes or modifications to this device not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this device. This device and its antenna(s) must not be co-located or operated
in conjunction with any other antenna or transmitter. This device complies
with part 15 of the FCC Rules.
Operation is subject to the following two conditions
- This device may not cause harmful interference
- This device must accept any interference received, Including interference that may cause undesired operation.
IMPORTANT NOTE:
Note This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the recover is connected
- Consult the dealer or an experienced radio/TV technician for help
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment
FCC ID:2AL9B-UPTBH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>