JJRC F184 Folding Drone With Obstacle Avoidance User Manual
- June 13, 2024
- JJRC
Table of Contents
F184 Folding Drone With Obstacle Avoidance
Product Information:
The product is a folding drone with obstacle avoidance
capabilities. It is suitable for users aged 14 and above.
Components:
- Drone
- 2.4G Remote Control
- Upper Casing
- Lower Casing
- Propeller
- Arm
- Battery
- Motor
- Camera
- Obstacle avoidance equipment
- Backup Propellers
- Protective Guard
- USB Charger
- Screwdriver
- User Manual
- USB Cable
Optional Accessories:
- Propellers
- Launch board
- Motor
- Receiving board
- Battery
- Protective Guard
Product Usage Instructions:
Pre-Flight Preparation:
- Flight Environment: For indoor flights, choose
spacious spaces away from barriers, crowds, or pets. For outdoor
flights, prefer sunny, windless, and breezy weathers. Keep the
drone in sight during the flight and away from barriers,
high-tension cables, trees, and people. Do not fly in extreme
environments such as hotness, coldness, strong wind, or heavy
rain.
Opening the Drone:
-
Open the Wings: Open the front arm (close to
camera) and then open the back arm. Fold the back arm firstly and
then the front arm when folding. -
Assembling Protective Guard: Align the
protective frame with the hole of the arm to install, and press it
into place. -
Assembling Propellers: Align the blades with
the motor shaft and install them (the arm identification must be
consistent with the blade identification). Tighten the screw
clockwise and cover the cap. -
Battery Charging for Drone: Remove the lithium
battery from the bottom of the drone. Connect the USB charging
cable with the charging interface of the lithium battery. The LED
light is red when charging and turns green when charging is
finished. Charging time is about 160-180 minutes.
Battery Instructions:
Using the lithium battery carries certain risks such as fire,
body injury, or property loss. Users must be aware of these risks
and take full responsibility for using the battery properly. Follow
these guidelines:
-
Do not contact your eyes or skin with electrolyte if battery
leakage occurs. Wash your eyes with clean water and seek medical
care immediately. -
If you sense any peculiar smell, noise, or smog, remove the
plug immediately. -
Use the charger from the original factory to ensure safe
usage. -
Do not charge dilatant or worn-out batteries. Do not overcharge
the battery. Unplug the charger once fully charged. Do not charge
the battery near inflammable objects or on electroconductive
surfaces. -
Always keep an eye on the battery when charging.
-
Do not charge a battery that has not cooled down yet. The
charging temperature should be between 0 to 40 degrees
Celsius. -
Dispose of the battery according to the local garbage disposal
method and special requirements. Do not dispose of it as daily
rubbish.
Remote Control:
The user manual does not provide detailed information about the
parts of the remote control. Please refer to the separate remote
control user manual for more information.
AGE 14+ FOLDING DRONE WITH OBSTACLE AVOIDANCE
FUNCTION OPERATING MANUAL
KNOW YOUR DRONE
Drone
2.4G
1 Upper Casing
2 Lower Casing
3 Propeller
4 Arm
1
5 Battery
6 Motor
7 Camera
8 Obstacle avoidance equipment
ACCESSORIES
DRONE x1 (Battery Included) x1 (
Remote Control x1 x1
A
B
Backup Propellers Ax1 Bx1 Ax1 Bx1
Protective Guard x4 x4
USB Charger x1 Screwdriver x1 User Manual x1
USB x1 x1
x1
Notes
2
OPTIONAL ACCESSORIES LIST
Propellers
Launch board
Motor
Receiving board Upper Casing
Lower Casing
Battery
Protective Guard
Notes
If any of the above accessories are damaged during operation, you can contact
the seller to purchase.
3
PRE-FLIGHT PREPARATION
1.FLIGHT ENVIRONMENT
Indoor: Spacious spaces away from barriers, crowds or pets are preferred.
Outdoor: Sunny, windless and breezy weathers are preferred.
Please keep the drone in sight during the flight and keep it away from
barriers, high-tension cables, trees and people.
Do not fly in extreme environment, such as hotness,coldness, strong wind or
heavy rain.
4
2.OPEN THE WINGS OPENING STEPS
Open the front arm(close to camera)
Open the back arm
Fold the back armf firstly and then the ront arm when folding.
Opening arm
3.ASSEMBLING PROTECTIVE GUARD
Align the protective frame with the hole of the arm to install, and press it
into place.
4.ASSEMBLING PROPELLERS
Align the blades with the motor shaft and install them (the arm identification
must be consistent with the blade identification), Tighten the screw clockwise
and cover the cap. (
5
5.BATTERY CHARGING FOR DRONE
A. Remove the lithium battery from the bottom of the drone.
B. Connect USB charging cable with the charging interface of the lithium
battery. USBUSB
Notes
The LED light is red on when charging, and the LED light is green when
charging is finished. Charging time is about 160-180 minutes. LEDLED 160-180
6
BATTERY LNSTRUCTIONS
There is a certain risk when using lithium battery. It may cause fire, body
injury or property loss. Users must be aware of the risks and take full
responsibility of using battery improperly.
If battery leakage occurs, please avoid contacting your eyes or skin with
electrolyte. Once it happens, please wash your eyes with clean water and seek
medical care immediately.
Please remove the plug immediately if you sense any peculiar smell, noise or
smog.
Battery Charging
Please use the charger from original factory to ensure your safe usage.
Do not charge dilatant or outworn battery. Do not over charge battery. Please
unplug the charger once fully charged. Do not charge the battery next to
inflammables, such as carpet, timber floor or wood furniture or on the surface
of electroconductive objects. Please always keep an eye on the battery when
charging.
Do not charge battery which not cool down yet. The charging temperature should
be between 0to 40.
Battery Recycling
Do not dispose the battery as daily rubbish. Please familiarize yourself with
the local garbage disposal method and dispose it according to the special
requirement.
7
KNOW YOUR REMOTE CONTROL 1.Parts of remote control
Standard version/Obstacle avoidance version /
The regular version is a light control key The obstacle avoidance version is
the obstacle avoidance mode button
High/low speed
Left joystick
//
One-key Ascend
One-key Landing
Phone clip
One-key Flips&Rolls 360°
Short press one key to calibrate Right joyustick // Power switch Headless mode
Fine-tuning key
Camera ESC version
Obstacle avoidance mode button
Camera up Left joystick
//
Camera down
One-key Ascend One-key Landing
Phone clip
One-key Flips&Rolls 360°
High/low speed Right joyustick // Power switch Short press Headless mode
Fine-tuning key
8
LITHIUM BATTERY INSTRUCTION
1 Open the remote control battery cover
2 Remote control battery installation
Open the battery cover and insert the 3 AA batteries correctly according to
the electrode instructions.(Batteries not included) 3AA
Notes
SIGNAL CONNECTION OF TRANSMITTER AND RECEIVER
9
TRANSMITTER CALIBRATION
Apply transmitter calibration when the drone fails to take off vertically.
Standard version/Obstacle avoidance version Press the “One button calibration”
buttonWhen the lights of drone are on and then start flashing and keep on
again, the calibration is complete. the drone must be placed on ahorizontal
surface in a steady state when the calibrationis conducted. / “”
Camera ESC version Move the left and right joysticks to the lower left at the
same time and hear a beep, then move the left and right oysticks to the lower
right to hear a beep. At this time, the UAV indicator light flashes quickly,
wait until the indicator light is always on, the calibration is completed.
When executing the correction command, it must be executed in a stable state
parallel to the horizontal line, otherwise the correction effect will be
affected.
10
“” “”
START YOUR FLIGHT
1. One-key Ascend
Press the “One-key Ascend” button, the drone blades rotate and automatically
fly to a height of 1.5 meters. “” 1.5
2. Basic Flight
Use the left joystick to control the flight altitude and turn left/ right, and
the right joystick to control the forward, backward, left and right sidde
flight directions.
Left joystick
Right joystick
11
Obstacle Avoidance Mode (The obstacle avoidance function
is only available when you purchase the obstacle avoidance version)
(
Press the button to turn on the obstacle avoidance mode, and press again to
turn off the obstacle avoidance mode. Avoid obstacles on four sides and
retreat in the opposite direction of the obstacle. It is recommended to turn
on the obstacle avoidance function in an indoor flight environment with a
length and width of 6 x 6 meters or more.When the UAV turns on the obstacle
avoidance mode, the speed will slow down and the fast gear cannot be turned
on. Therefore, it is recommended to fly indoors when the obstacle avoidance
mode is turned on. 6×6
Flips & Rolls
Right joystick
12
Headless Mode
The flight direction of drone is subjected to the direction of remote control.
1.When drone adjust the frequency, the drone is default as
common mode. Then the indication light of drone is normally on. When you press
the headless function key of remote control, the remote control beeps once and
enters headless state. When you press the headless function key again, you
listen to a long beep sound and the drone exits the headless mode. 2.In the
headless state, operator doesn’t need to identify the direction of nose, but
control the drone according to the operating lever of remote control. “” “”
Hover
Left joystick
Camera angle adjustment
During the flight of the drone, the camera angle can be adjusted through the
camera adjustment button. (This function is only available in the camera ESC
version)
13
FINE-TUNING FUNCTION
When the aircraft spins in the air or tilts in different directions, you can
use fine-tuning to correct the action. Press the fine-tuning button and hear a
beep, then move the joystick in the opposite direction to adjust and calibrate
until the aircraft does not deviate. If there is no operation for 5-6 seconds
after entering the fine-tuning, the fine-tuning function will automatically
exit. “” 5-6
Notes
14
FAQ
15