Yale YRD510-MT1 Keyed Deadbolt Installation Guide

Yale YRD510-MT1 Keyed Deadbolt

Specifications

• FCC ID: MZR-YRD510
• IC ID: 2676A-YRD510
• Compliance: FCC Part 15.19, FCC Part 15.21, Industry Canada
• Class: B Equipment
• Model: P/N YRD450-N-MNL-0039 Rev A

Product Information

The product is designed to work specifically with Apple technology and has been certified to meet Apple performance standards. It features compatibility with Google products such as Google Play and Google Home, as well as Amazon products like Alexa.

YRD510 Keyed Deadbolt  installation Gu1ide

Notice: Before installing your tock, be sure to follow the steps on the yellow Quick t Guide.

Failure to follow these instructions could result in damage to 1e product, voiding the factory warranty and cou d l read o failure of the product provide access.

In The Box

Remove Existing Dea bolt
Keep your old deadbolt until your new lock has been successfully in. sralled.

Check Door Measurements and Adjust If Needed

Check Door:
Tear off the Door Checker page of this guide and follow the instructions to verify your door measurements and make any needed adjustments.

Note: There are some cases where existing holes cannot be adjusted to be compatible.

New Door:
Tear off the Template page of this guide and use either 2-1/8″ or 1-1/2″ template to prepare a new door that has no holes or to adjust existing holes to be compatible.

Verify Measurements with the Check Your Door Guide

CAUTION : If printed from an electronic file, set the print scale to 1:1. Measure ruler to check scale.

Check Your Door Guide
To ensure a successful installation, measure each aspect of your door and frame, as shown in panels (left side of sheeting

• 2″ Minimum clearance between top of existing lever/knob rose (trim) and center of deadbolt hole. 2″ tolerance for optimal Door Sense location.
• 1-3/8″ Door Thickness; use blue Screw Set B (shortest set). C. 1-3/8″ – 1-3/4″ Door Thickness; use black Screw Set
• D. 2″ – 2-1/4″ Door Thickness; use silver Screw Set
• (longest set).
• 2-3/8″ Backset; use Out of Box latch setting-
• 2-3/4″ Backset; adjust latch setting. Instructions on how to adjust the latch are included in manual.
• 1-1/2″ Face Bore Diameter. Instructions on how to remove the black adapter from the lock are included in manual 1-1/2″ tolerance from inside door frame edge for optimal DoorSense location.
• 2-1/8″ Face Bore Diameter.
• Edge Bore Diameter and Depth. Cross Bore Diameter.

Te1rnplate to Mark a Door for 2-1/811 Face Bore

Install Deadbolt Latch and Strike Plate

*Correct deadbolt latch length is based on backset. Choose 2-3/8″ or 2-3/4″.
Door Checker measurements E and F can help you verify your backset measurement.

Attach Wire to Inside of Interior Lock

Using Your Lock

Features

Setting Definitions

Keypad Alerts

Interior Lock Light Alerts

Use

• Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards.
• Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
• Apple®, Apple Home™, Apple Watch®, HomeKit®, and iPhone® are trademarks of Apple Inc., registered in the U.S. and other countries and regions.
• Google, Google Play and Google Home are trademarks of Google LLC.
• Amazon, Alexa and all related logos are trademarks of Amazon.com Inc. or its affiliates.
• Wi-Fi is a registered trademark of Wi-Fi Alliance®.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ASSA ABLOY Residential Group Inc. is under license. Other trademarks and trade names are those of their respective owners.

RF Exposure Statement

FCC and IC RF Radiation Exposure Statement
This equipment complies with FCC and IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co- located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

FCC :
FCC ID: MZR-YRD510 IC I D: 26 76A-YRD510

FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Part 15.21
Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.

Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning:
Changes or modifications to this device, not expressly approved by Yale Home could void the user’s authority to operate the equipment.

Industry Canada:

FCC ID: MZR-YRD510
IC ID: 2676A-YRD510

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2.  This device must accept any interference, including interference that may cause undesired operation of the device.

24/7 Support: 1-855-213-5841 • US.YaleHome.com

Yale® and Assure Lock® 2 are registered trademarks of Yale Home. Other products’ brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. ©Copyright 2023. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Home is prohibited.
P/N YRD450-N-MNL-0039 Rev A

References

• . Spend less. Smile more.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>