JJRC H111 Quadcopter 8K HD Dual Camera Instruction Manual

Instruction manual for quqdcopter

H111 Quadcopter 8K HD Dual Camera

• In order to ensure the magnetic environment requirements of aviation radio stations, (it is prohibited to 10 km on both sides of the runway center line, 20 km on both ends of the runway) and open aif routes and routes. Stop using all kinds of models and drones. The use of all kinds of models and drones will be stopped in no-fly zones issued by relevant state departments

warning

1. Packaging and instructions contain important information and should be retained.

2. You are responsible for ensuring that this aircraft wil not cause harm to others’ personal and
   property.

3.  The commissioning and installation of the aircraft must be operated in strict accordance with the operating instructions. Attention shouid be paid to keeping the aircraft 2-3 meters away from users or other people when flying, 5o as to prevent the aircraft from hitting people’s head, face and body when flying or landing, causing injuries.

4. Our company and the seller are not responsible for any loss, damage and human injury caused by improper use or operation.

5.  Children should be guided by adults when operating aircraft. Children under 14 years old are prohibited to operate this product.

6. Please correctly install and use according 1o the instructions or packaging instructions. Some parts should be assembled by adults.

7.  If the product contains small parts, please place them out of the reach of children to prevent accidental ingestion or room breathing hazards.

8.  It is strictly prohibited to play on the road o in places with water to avoid accidents.

9. Please put away the packaging materials i time to avoid injury to children,

10. Do not disassemble or refit the aircraft, which may cause failure.

11. The charging ine shall be inserted into the specified power supply 5V/=2A which is the same as the product label.

12.  The use of other charging lines will cause battery damage and may cause accidents.

13. The charging cable is not a toy.

14. The charging of rechargeable battery must be carried out under the supervision of an adult.
    The charging must be kept away from combustibles. The supervisor must not leave the monitoring range during charging.

15. Please do not short circuit or squeeze the battery to avoid explosion.

16.  Do not mix different types of lithium batteries.

17. The aircraft uses rechargeable lithium batteries, which need to be unplugged for charging.

18.  Do not short-circuit, disassemble or put the battery into fire; Do not place the battery in a hot and heated place (such as a fire or near an electric heating device),

19.  The aircraft shall be used as far away from other electrical equipment and magnetic objects as possible, which may cause mutual inerference.

20. Please keep a safe distance from the high-speed rotating propeliers to avoid the risk of entanglement and cuts.

21. The molor s a hot part. Please do not touch it to avoid bums.

22. light emitting diode laser radiation, do not direct beam.

23.  Do ot use the model near the ear! Misuse may cause hearing damage.

24.  The USB charging cable must use the data cable provided by the company to charge the battery, otherwise t will cause serious damage to the batery, which willlead to unexpected danger.

25.  In order to ensure the requirements of the magnetic environment of the aviation radio station, the use of the model remote controller should be stopped in the district as required during the period when the relevant national departments issue radio control orders.

26.  When the aircraft battery is used up, be sure 1o tun off the switch and unplug the battery, and charge it after 30 minutes of inactivity, otherwise the battery may be damaged.

Include a list of accessories:

Name of each part of the aircraft:

Before takeof, please follow the steps in the above order: Open (refer to 11.1) Remote conrl stats rquency maihing(wer o 11.2) Horzontal calbratn (fr o 113) Startstop (refer to 11.4) ™ One button takeoff and landing (11.5)

Expansion diagram of aircraft : ( in storage stae when leaving the

factory)

Install the protection rack

4.1 Install the protection rack according to the following steps

According to the diagram, align the protective frame parts with the arm socket for docking, and confirm the installation in place before flying to avoid falling during the flight.
Note: Please be sure to install the protective ring before flying

Blade replacement:

5.1 Installing Air Blades
Use a screwdriver to remove the screw. Unable to take oft

Blade A is broken, replace blade A. blade B is broken, replace blade B, the replacement is wrong
Note: The blades are printed with letters A and B. Please install them correctly according to the diagram, otherwise they cannot take off..

Lithium battery instructions

6.3 Charging: Plug the USB port of the USB charging cable into the USB port of the computer (or use the power adapter with output of 5V=2A) and connect the other end of the USB charging cable to the battery socket. When charging, the indicator light of the USB interface will be on. When the battery is full, the indicator light of the USB interface will be off, and the charging is complete. The aircraft charging cable provided by our factory must be used to charge, not other charging cables. Remember to avoid the danger of accidents.
WARNING When not flying the aircraft, remove the battery from the bottom of the aircraft to avoid battery damage

Remote control installation and expansion

Name of each part of the remote control

Remote control battery Installation:

Note when charging:

• Do not place charged batteries in places where they are exposed to high temperature, such as open flames or electric heating devices, or they may be damaged or explode.
• Do not hit or knock hard surfaces with batteries.
• Do not disassemble the battery
• Do not immerse the battery in water. Store the battery in a dry place.
• Do not leave while charging.

Pre-flight environmental requirements:

Please choose to fly in an open environment with no wind or snow, and stay away from people. trees. power lines, tall buildings, airports and signal towers. Don’t fly in an indoor environment that’s too small and full of stuff.

Pre-flight preparation instructions: (Use remote control.)

11.1 Frequency alignment of aircraft:
Turn on the power supply of the aircraft and place it on the horizontal plane. At this lime, the aircraft placed on the horizontal plane automatically enters the frequency matching state, and the front white light flashes.

Note: Position the aircraft with the nose straight ahead and be sure to place it on the level ground

11.2 Turn on the remote control switch (Step 1). the power indicator of the remote control is on. the throttle rod is pushed upward to the top (step 2) and then to the bottom (step 3). the frequency is successfully set, and the aircraft light turns from flashing to steady on. The aircraft/remote control must be fully charged or it cannot take off!

11.3 Horizontal calibration operation:
Press the one-button calibration button of the remote control and the LED flash on the aircraft The LED on the aircraft is steady on and the calibration is complete. The remote control makes a sound of ‘drip’. (Figure 1)

11.4 Start/Stop:
Push the left joystick on the remote control upward (Figure 2), then the aircraft can take off normally, and all lights of the aircraft will be steady on after takeoff. During startup, pull the left Joystick down and the aircraft slowly stops.

11.5 One-button take-off and Landing:
After the frequency alignment is completed, press me -One-button Take- off/Landing’ function button of the remote control (as shown in Figure 4), and the aircraft will automatically rise to a height of about 1 meter and maintain a stable flight. Then, the aircraft will land slowly and automatically when you press this function button.

Remote control operation method:

| When the left joystick (throttle) pushes up. the rotation speed of the main blade increases and the aircraft nses.
When the left joystick (throttle) is pushed down, the rotation speed of the main blade slows down and the aircraft descends.
---|---
| When the left joystick (rudder) is pushed to the left. the aircraft nose turns to the left Push to the right and turn the nose of the vehicle to the right.
| When the right joystick (rudder) is pushed up. the vehicle moves forward
When the right joystick (rudder) is pushed down, the vehicle retreats
| When the right joystick (rudder) is pushed to the nght. the aircraft fuselage flies to the right.
When the right joystick (rudder) is pushed to the left, the aircraft fuselage flies to the left.

13.360° Roll:
The aircraft can fly 360 degrees through the following rocker operation. In order to better perform the tumbling function, ensure that the aircraft and the ground maintain an altitude of about 1.5 meters. it is better to operate the aircraft to roll during the ascent, so that the aircraft will be easier to maintain the altitude after tumbling.

| 13.1 Left 360′ Roll Short press the 360′ roil button, then push the right joystick to the left. and the aircraft will flip 360′ to the left correspondingly.
---|---
| 13.2 Right 360′ Roll Press the 360° roll button short, then push the nght joystick to the nght, and the aircraft will flip 360′ to the nght correspondingly.
| 13.3 Forward 360′ Roll Press the 360′ roll button short, then push the nght joystick upward, and the aircraft will flip 360′ forward accordingly.
| 13.4 Backward 360′ Roll Short press the 360′ roll button, then push the nght joystick downward, and the aircraft will flip backward 360′ accordingly

Function operation of the remote control:

14.1 Headless Mode
The front of the aircraft when the frequency is switched on is the front of headless mode by default; If you need to adjust the direction you need, please restart the set frequency and press the “Headless Mode” button of the remote control (Figure 4). When exiting, please tap the function key again. Special tip: Please be sure to align the aircraft to the straight line, so that the gyroscope can automatically detect the straight line, in order to realize the headless mode of straight line flight.

14.2 Light on and off
Long press the light function key of the remote control (Figure 5) to turn off the light of the remote control, and long press again to turn on the light.

14.3 Speed Switch
When the aircraft takes off, the default mode is low speed (3 gear switch). Press the remote control “di” once for low speed gear, “didi- twice for medium speed gear, and “thdidi- three times for high speed gear (FIG. 6).

Common Problem Solving Guidelines:

2 Replace the blade
The aircraft vibrates badly| Blade deformation| Replace the blade
Fine tune to the end, but still can not make the aircraft stable| 1. Blade deformation
2. Poor motor| 1. Replace the blade
2 Replace the motor
Launch the aircraft again after impact and fly uncontrollably| The three-axis accelerabon sensor loses balance due to impact| It can be corrected by correcting the gyroscope

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>