SEALEY LED450UV Penlight Torch with UV 5W COB and 3W SMD LED with Laser Pointer Rechargeable Instructions
- June 4, 2024
- SEALEY
Table of Contents
PENLIGHT TORCH WITH UV 5W COB
& 3W SMD LED WITH LASER POINTER
RECHARGEABLE
MODEL NO: LED450UV
Instructions Manual
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instructions
|
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
---|---
SAFETY
1.1. GENERAL SAFETY
Ensure the penlight torch is fully charged before initial use.
DO NOT charge in damp conditions.
DO NOT turn the penlight torch on when it is being charged.
DO NOT shine the penlight torch beam into your, another person’s, or an
animal’s eyes.
DO NOT allow children to use the penlight torch.
DO NOT handle or move the penlight torch while it is being charged.
DO NOT use the penlight torch if you suspect that the battery or the
penlight casing is damaged.
DO NOT leave the battery in a discharged state. Recharge the battery
immediately.
Before storage, fully recharge the battery.
Recharge the battery at least every six months of non-use.
Disconnect the USB-C cable after charging.
DO NOT attempt to open, disassemble, modify or service the battery.
DO NOT crush, puncture or dispose of in fire or water.
Recycle or dispose of penlight torch as stipulated by local regulation.
‰ WARNING! Keep away from extreme temperatures, especially heat.
1.2. LASER SAFETY
‰ WARNING! Children under six years old should not use this product
without adult supervision.
‰ WARNING! DO NOT deliberately look or stare into the laser beam.
Permanent eye damage could result.
DO NOT shine the laser beam into another person or an animal’s eyes.
‰ WARNING! If the laser beam is obstructed by another person during use,
switch it off immediately.
DO NOT point the laser beam at aircraft or a vehicle that is in motion.
‰ WARNING! Be aware that a reflected laser beam from mirrors or other
shiny surfaces can be as hazardous as direct eye exposure.
‰ WARNING! The warnings, cautions, and instructions in this manual cannot
cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors that
cannot be built into this product but must be applied by the operator.
INTRODUCTION
Professional aluminum design that produces ultraviolet light for fault finding with fluorescent dyes used in leak detection. 5W COB side floodlight producing 450 lumens. Also features a 3W SMD tail light and type 3R laser. Rechargeable 800mAh Li-ion battery with a type C charging cable. 120 degrees rotating metal clip with a strong magnet for easy hands-free use. Also includes a dimming switch.
SPECIFICATION
Model No: …………………………………………………… LED450UV
Battery Type: ……………………………………………..3.7V 800mAh
Input (USB Type-C): ……………………………………. 5V (dc) 0.5A
Charge Time: ………………………………………………………… 3hrs
Work Light Source: ………………………………………….. 5W COB
Work Light Brightness: …………………………………..450 lumens
Work Light Runtime:……………………………………………….2.5hr
Torch Source: …………………………………………………..3W SMD
Torch Brightness: ………………………………………….140 lumens
Torch Runtime: ………………………………………………………2.5hr
Product Dimensions (L x D x W): …. 165mm x 23mm x 19mm
LED Type: ……………………………………….5W COB + 3W SMD
365nm UV Light Source: …………………………………… UV Light
365nm UV Light Runtime: ………………………………………….4hr
Laser Light Source: …………………………………………Red Laser
Laser Light Runtime: …………………………………………… >20hrs
OPERATION
4.1. CHARGING THE PENLIGHT TORCH
4.1.1. Lift up and rotate the charging port cover (fig 1) and insert the
USB-C cable into the charging port (fig 1).
4.1.2. Insert the other end into either a USB wall charger, a car
accessory charger, or the USB port on a computer (non-supplied).
4.1.3. While charging the battery power indicator flashes a green light
(fig 2). One flashing light indicates a 0-20% charge.
4.1.4. When all five indicator lights are illuminated the battery is
fully charged.
4.1.5. When the penlight torch is fully charged disconnect from the
charging source. DO NOT leave the penlight torch on charge for long
periods.
4.2. ON/OFF SWITCH
NOTE: The ON/OFF switch acts as a multifunctional switch to control light
selection.
4.2.1. Press the ON/OFF button and the bottom spotlight will illuminate
(fig 2).
4.2.2. Press the ON/OFF button a second time and the front floodlight
will illuminate (fig 2).
4.2.3. Press the ON/OFF button a third time and the top UV light will
switch on (fig 2).
4.2.4. Press the ON/OFF button again and the penlight torch will turn off
(fig 2).
4.3. DIMMER CONTROL
NOTE: The dimmer function will only operate in the spotlight or
floodlight mode.
4.3.1. In the desired mode press and hold the ON/OFF button to dim or
brighten the light setting (fig 2).
4.4. LASER BUTTON
4.4.1. Double press the laser button to turn the laser light on (fig 2).
4.4.2. Single press the laser button to turn off the laser light (fig 2).
‰ WARNING! Be aware of the orientation of the penlight torch when turning
on the laser light.
It is recommended that you point the laser light toward the ground when
turning it on.
4.5. MAGNETIC CLIP
4.5.1. Attach the penlight torch to a metal surface in your desired
position.
4.5.2. The penlight torch can be rotated through 120º to suit (fig 3).
MAINTENANCE
5.1. After each use recharge the penlight torch.
5.2. After charging or usage remove all cables or connections.
5.3. Use a clean, dry cloth to wipe the penlight torch after use.
DO NOT use solvents.
5.4. When not in use store the penlight torch in its original packaging
in a safe, clean, dry childproof location.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories, and packaging should be sorted, taken to a recycling center, and
disposed of in a manner that is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd
are required to inform potential purchasers of products containing batteries
(as defined within these regulations), that they are registered with Valpak’s
registered compliance scheme. Jack Sealey Ltd’s Batteries Producer
Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications, and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way,
Suffolk Business Park,
Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
LED450UV Issue 1 28/04/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>