Bestway 56466 Rack Pool Instruction Manual
- June 13, 2024
- Bestway
Table of Contents
Bestway 56466 Rack Pool
WARNING
WARNING
smooth out the bottom Put 1″ to 2″ water in the pool to cover the floor. Once
pool floor is slightly covered, gently smooth out all wrinkles. Start in the
center of the pool and work your way clockwise to the outside.
Do not assemble on soft lawn. If you must assemble the pool on a soft surface, timber boards must be placed under the feet of the vertical supports to spread the load. The thickness of the timber boards must not exceed 2 cm.
POWER STEEL™| 2.82 m x 1.96 m x 84 cm
(9’3″ x 6’5″ x 33″)
| 4.04 m x 2.01 m x 1.00 m
(13’3″ x 6’7″ x 39.5″)
| 4.12 m x 2.01 m x 1.22 m
(13’6″ x 6’7″ x 48″)
| 4.88 m x 2.44 m x 1.22 m
(16′ x 8′ x 48″)
| 5.49 m x 2.74 m x 1.22 m
(18′ x 9′ x 48″)
| 6.40 m x 2.74 m x 1.32 m
(21′ x 9′ x 52″)
| 7.32 m x 3.66 m x 1.32 m
(24′ x 12′ x 52″)
| 9.56 m x 4.88 m x 1.32 m
(31’4″ x 16′ x 52″)
---|---|---|---|---|---|---|---|---
56629 / 56631| 56441 / 56426
56442 / 56660
56721 / 56727
| 56456 / 56457
56458 / 56661
56722 / 56728
| 56670 / 56671
56672 / 56673
56995 / 56996
| 56465 / 56466
56467 / 56468
56997 / 56998
| 5611Y / 5611Z
5612A / 5612B
| 56474 / 56475
56476 / 56477
| 56623 / 56625
A| x2| x2| x2| x2| x4| x6| x8| x12
B| x2| x2| x2| x2| x2| x2| x2| x2
C| x2| x2| x2| x0| x2| x2| x2| x2
D| x2| x2| x2| x2| x2| x2| x2| x2
E| x0| x2| x2| x2| x2| x2| x2| x2
F| x0| x0| x0| x4| x0| x0| x2| x4
G| x4| x4| x4| x4| x4| x4| x4| x4
H| x4| x6| x6| x12| x12| x14| x18| x24
I| x4| x4| x4| x0| x0| x0| x0| x0
J| x1| x1| x1| x1| x1| x1| x1| x1
K| x2| x2| x2| x2| x0| x0| x0| x0
L| x1| x1| x1| x1| x1| x1| x1| x1
M| x1| x1| x1| x1| x1| x1| x1| x1
N| x0| x0| x0| x0| x2| x2| x2| x2
O| x0| x0| x0| x0| x1| x1| x1| x1
P| x0| x0| x0| x0| x1| x1| x1| x1
STRUCTURE
Before assembling your pool, please take a few minutes to check all the parts
and become familiar with their position.
NOTE : Drawing for illustration purpose only. May not reflect actual
product. Not to scale.
2.82 m x 1.96 m x 84 cm (9’3″ x 6’5″ x 33″)
4.04 m x 2.01 m x 1.00 m (13’3″ x 6’7″ x 39.5″)
4.12 m x 2.01 m x 1.22 m (13’6″ x 6’7″ x 48″)
4.88 m x 2.44 m x 1.22 m (16′ x 8′ x 48″)
5.49 m x 2.74 m x 1.22 m (18′ x 9′ x 48″)
5.49 m x 2.74 m x 1.22 m (18′ x 9′ x 48″)
7.32 m x 3.66 m x 1.32 m (24′ x 12′ x 52″)
9.56 m x 4.88 m x 1.32 m (31’4″ x 16′ x 52″)
INSTALLATION
Installation usually takes approximately 20-30 minutes with 2-3 people
excluding earthworks and filling.
Assembly of the Frame Pool can be completed without tools. To lengthen the
life of your pool, it is important to sprinkle the to pail with the Talcum
Powder before assembly. Talcum Powder is not included and easily available in
the market.
Bestway will not be responsible for damage caused to the pool due to
mishandling or failure to follow these instructions.
- Lay out all parts and check that you have the correct quantities as listed in the components list. For assistance or FAQs, please visit the support section on our website, www.bestwaycorp.com.
- Spread out the pool and make sure the pool is right side up; let it sit exposed to direct sunlight for 1 hour or more so that the pool is more flexible during set up.
- Place the pool near an adequate drainage system to deal with overflow water and ensure the pool’s inlet A and outlet B are correctly positioned to allow your filter pump to connect to a power source.
NOTE: Do not use extension power cords to power your pump.
ATTENTION: Do not drag the pool on the ground, this can damage the pool.
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
CONNECTION VALVE ASSEMBLY
For pool with connection valve.
NOTE: If you want to connect other pool cleaning kits to the pool through
the connection valve, disassemble the Debris Screen from the Connector.
FILLING POOL WITH WATER
ATTENTION: Do not leave pool unattended while filling with water.
-
Fill the pool until the water reaches the welding line located 12cm-20cm (4.7”-7.9”) from the top of the pool. DO NOT OVERFILL as this could cause the pool to collapse. In times of heavy rainfall you may need to empty some of the water to ensure the level is correct.
-
When filling the pool is completed, check that the water is not collecting on any side to ensure the pool is level. IMPORTANT: If pool is not level, drain water and re-level ground by digging out. Never attempt to move the pool with water in it, serious personal injury or damage to the pool may result.
WARNING: Your pool may contain a great deal of pressure. If your pool has any bulge or uneven side then the pool is not level, the sides may burst and the water may discharge suddenly causing serious personal injury and/or damage to property. -
Check pool for any leaks at valves or seams, check any evident water loss. Do not add chemicals until this has been done.
For support please visit us at: bestwaycorp.com/support
©2021 Bestway Inflatables & Material Corp.
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon,
Hong Kong
Tel: +86 21 69135588 (For U.S. and Canada)
www.bestwaycorp.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>