ATOMRC G1500 Seal Wing 1500mm Wingspan Epo Fpv Glider Rc Airplane Kit User Manual

ATOMRC G1500 Seal Wing 1500mm Wingspan Epo Fpv Glider Rc Airplane Kit

Introduction

The seal is classic glider design,easy for beginners,with a detachable wing design,user can choose 1100mm wing span or use extend wing to 1500mm wingspan for different style of Fly. Design for FPV,the ESC,FC VTX and Camera all have installation area.Side door for install Flight controller,easy to wiring and maintain.Easy to build and maintain

Specifications

• Wingspan: 1100/1500mm
• Length: 950mm
• wing area: 17.8/25.7d㎡
• Material: EPO
• Recommend Motor: 2212 1400KV
• Recommend ESC: 30A 2~4S
• Recommend Propeller: 8040
• Servo: 9g Servo*4PCS
• Recommend Battery: 21700 4S1P/3~5000mAH 4s

Installation Diagram

KIT Contents

• A: Hatch
• B: Cam hatch
• C: Side hatch
• D: Fuselage
• E: Horizontal tail
• F: Tail
• G: Wing
• H: Wing Extend
• I: Wing tube hatch

Packing List

Installation

1. Glue the frame VTX mount and Motor mount.
2. Glue the frame to the other side of fuselage then glue the fuselage.
3. Install the battery strap , glue the battery mount board to the fuselage.
4. Install magnet and hatch lock to the side hatch, ESC mount.
5. Install the rudder control surface, servo and push rod.
6. Install the elevator control surface, servo and push rod.
7. Glue the tail.
8. Glue the body, and hatch lock.
9. Glue the main carbon tube, tube clip.
10. Please do not glue the dark part shown above, otherwise, the carton tube will to tight to install.
11. Glue the side plate and control surface reinforcement carbon rod.
12. Glue the servo, install the push rod.
13. Assemble the wing to the body, tighten the screw to lock the wing.
14. Glue the plastic skid.
15. Install the motor and ESC.
16. Install the Camera, install the camera cable.
17. Install the GPS, VTX and Flight Controller.

How to install 1100mm Wing Span

If user want use an 1100wing span, the wing carbon tube need change 200mm.

ESC Information

1. The ESC included with the model has a safe start.If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position,the motor will not start untill the throttle stick is moved to the low throttle or off position.Once the throttle stick is moved to the low throttle or off position,the motor will emit a series of beeps.the motor is now armed and will start when the throttle is moeved.make sure receiver is bind to the radio, turn on the radio, set throttle stick to the maximum.
2. Power on the ESC(The ESC must connect to the motor and Receiver). The motor will emit a series of beeps, after the beeps, set the the throttle stick the the minimum, the motor will emit a series beep again. now the ESC calibration is done.

VTX User manual

VTX Specs

• Voltage input: 2~6S Lipo
• Frequency: 5.3~5.9Ghz
• Power: 200/800/1500mw Switchable
• Power consumption: 9V 1.1A

VTX Setting

1. Hold button 3 seconds into setting mode.
2. In setting mode. short press the button to change band.
3. Then hold button 3 seconds into CH setting mode, short press button to change CH.
4. Hold button 3 second to get into Power setting mode, there is short bar on LED, short press to switch power, 1 bar means 200mW, 2 bar means 800mW, 3 bar means 1500mW.

Please download the latest user manual at www.atomrc.com/pages/download

References

• Download – ATOMRC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>