Honeywell Home PRO 1000 Series Non-Programmable Thermostat User Guide
- June 7, 2024
- Honeywell Home
Table of Contents
Honeywell Home PRO 1000 Series Non-Programmable Thermostat User Guide
PRO 1000
Product Information
TH1100DH: For 1 Heat systems
TH1110DH: For 1 Heat/1 Cool systems
TH1110E: For 1 Heat/1 Cool systems
*TH1110E model has a larger display than pictured
TH1210DH: For 2 Heat/1 Cool heat pump systems
Quick reference to controls
- Cool: Cooling system control.
- Off: All systems off.
- Heat: Heating system control.
- Em Heat: Emergency & Auxiliary Heat control. Compressor is locked out. (Select models only.).
Quick reference to display screen
* _When “Heat On” or “Cool On” is flashing, compressor protection is engaged._**
Adjust the temperature
- M32822
Note: Make sure the thermostat is set to the system you want to control (heat or cool).
Read before installing
Built-in compressor protection
This feature helps prevent damage to the compressor in your air conditioning
or heat pump system.
Damage can occur if the compressor is restarted too soon after shutdown. This
feature forces the compressor to wait 5 minutes before restarting.
During the wait time, the display will flash the message Cool On. When the
safe wait time has elapsed, the message stops flashing and the compressor
turns on.
CAUTION
Equipment damage hazard
To prevent possible compressor damage, do not operate cooling system when
outdoor temperature is below 50°F (10°C).
Battery replacement
Install two fresh AAA batteries when Lo Batt flashes on the screen. Lo
Batt appears for 60 days before the batteries are depleted.
Replace batteries once a year, or when you will be away for more than a month.
The settings are stored in non-volatile (permanent) memory and are thus
preserved when the thermostat is without batteries.
Product manuals
Search online for Resideo 69-2607EFS for the User Guide.
Electrical ratings
System
|
Voltage (50/60Hz)
|
Running Current
---|---|---
Heat (1st stage)
| 20-30 Vac|
0.02-1.0 A
(Powerpile)
|
750 mV DC
|
100 mA DC
Auxiliary heat
|
20-30 Vac
|
0.02-1.0 A
Cooling|
20-30 Vac
|
0.02-1.0 A
In case of difficulty
If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.
Display is blank|
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
- Make sure fresh AAA alkaline batteries are correctly installed
---|---
Heating or cooling system does not respond
|
- Set system switch to Heat. Make sure the temperature is set higher than the Inside temperature.
- Set system switch to Cool. Make sure the temperature is set lower than the Inside temperature.
- Wait 5 minutes for the system to respond.
“Heat On” or “Cool On” is flashing
|
- Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor .
“Heat On” is not displayed
|
- Set the System switch to Heat, and set the temperature level above the current room temperature
“Cool On” is not displayed
|
- Set the System switch to Cool, and set the temperature level below the current room temperature
www.resideo.com
Resideo Technologies Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
https://www.honeywellhome.com/support
33-00529EFS—03 M.S. Rev. 07-20 | Printed in United States.
© 2020 Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell
International, Inc. This product is manufactured by Resideo Technologies, Inc.
and its affiliates.
References
- Smart Home Products and Systems | Resideo
- HACCP poročilo o temperaturah | Temperature.si | Upravna enota Maribor
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>