ATOMRC HP171-0002 Killer Whale RC Airplane User Manual

ATOMRC HP171-0002 Killer Whale RC Airplane

Introduction

1. the killer whale is 1200mm wingspan twin motor fixed wing.
2. The main wing can be quickly disassembled and assembled for easy carrying.
3. Exclusive installation positions for the flight controller , VTX, antenna, and battery compartment, which are easy to install and organize. max support 9inch propeller.
4. The double vertical tails are directly behind the propellers, which increase the control performance of the aircraft rudder and make it easier to land.
5. Supports Gopro hero 9 and is compatible with hero 5/6/7 installation on the head or rear.

Specifications

Killer Whale Specifications

Wingspan| 1255mm
Length| 890mm
WingArea:| 21d㎡
Material:| EPP
Servo Specs:| 9g Servo300mm5Pcs
Flap Servo:| 9g Servo200mm2Pcs

（包含1个反向舵机）

Recommend Motor:| 2306~2212
Recommend ESC:| 30A 2~4S
Recommend Propeller:| 7040-3
Recommned Battery:| 21700 2p4s

Version Description

KIT Contents

• A：Fuselage
• B：WING
• C：Front hatch cover
• D：Motor hatch cover
• E：Wing wiring cover
• F：Landing gear cover
• G：Bottom hatch cover
• H Top hatch cover
• I：Rudder
• J：Tail
• K：Gopro hatch cover
• L：Nose

KIT Lite Installation/KIT Lite

1. Install the Nuts on the tail, VTX mount on the fuselage.

2. Install the carbon plate mount for camera.

3. Install the magnet, hatch lock, wood plate on the fuselage.

4. Install the magnet on each hatch cover.

5. Install the Nuts and motor mount on the wing.

6. Install the control horn on each control surface.

KIT/PNP/FPV Installation

1. Install the servo and push rods, then install the rudder.

2. Landing gear mounting hole position

Install the Motor, ESC, servo and push rods, and install the wing tip

3. Install the quick detatch wire with rubber ring, plug the servo, ESC to the wire. then wire the Power distribution board.

4. Install the Motor hatch cover , and install the Rudder and Tail.

ATOMRC KWPDBV2

the signal on the wing is parallel on the PDB, the PDB need external 5V BEC to power the servo.

ESC Information

Throttle calibration

1. The ESC included with the model has a safe start.If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position,the motor will not start untill the throttle stick is moved to the low throttle or off position.
2. Power on the ESC(The ESC must connect to the motor and Receiver). The motor will emit a series of beeps, after the beeps, set the the throttle stick the the minimum, the motor will emit a series beep again. now the ESC calibration is done.

ESC

• Voltage input : 2~4S Lipo
• Max Current : 35A
• Output ：Built in 5V 3A BEC/5V 3A BEC

VTX Tx15 Uermanual

Tx15 Wiring Diagram/Tx15

Please make sure antenna is installed before power on, otherwise the VTX will fried!!!

Tx15 Specs/Tx15

• Voltage input : 2~6S Lipo
• Power : 200/800/1500mw Switchable
• Power consumption : 9V 1.1A
• Frequency:5.3~5.9Ghz

VTX Setting

1. Hold button 3 seconds into setting mode.
2. In setting mode. short press the button to change band.
3. Then hold button 3 seconds into CH setting mode, short press button to change CH.
4. Hold button 3 second to get into Power setting mode, there is short bar on LED, short press to switch power, 1 bar means 200mW, 2 bar means 800mW, 3 bar means 1500mW.

Please download the latest user manual at www.atomrc.com/pages/download

References

• Download – ATOMRC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>