ATOMRC Swordfish Fixed Wing User Manual
- June 9, 2024
- ATOMRC
Table of Contents
ATOMRC Swordfish Fixed Wing
Introduction
The swordfish is a 1200mm wing span middle speed twin motor glider, the large V-tail improves the cruising speed stability, the aerodynamic shape and low cross-sectional area reduce flight resistance and improve endurance.
We use lots of plastic injection parts to reduce the wight, size and also improved the strength. The fuselage and the wing are embedded with reinforced carbon tubes to maximize the torsional rigidity of the wing during flight and the structural strength of the tail connection. Improved the control of precise flight. The belly wheel and the tail skid design protect the bottom of the fuselage from landing.
The glider support DJI air unit, also support analog system, the 1000g±200g take off weight made the plane achieves balanced load on the take-off wing, balanced cruise speed, and convenient assembly and maintenance.
Specifications
Swordfish Specifications/剑⻥规格
Wingspan| 1200mm
Length| 810mm
WingArea| 15.35d㎡
Servo| 9g Servo*4PCS
Material| EPP
Recommend Motor:| 2004~2306
Recommend ESC:| BLS 30A 2~4S
Recommend Propeller| 7040-2
Recommend Weight| 1200g
Version Description
ATOMRC Swordfish Fixed Wing
| Version| KIT| PNP| FPV| RTH| RTF+FPV
|
Description
|
Pre-glued Fixed WING
|
KIT+Motor
+ESC+Servo
|
PNP+VTX+C
amera
| PNP+Pre-
turned FC+GPS, all electronics
are installed
| RTH+VTX+C
amera, all electronic are installed
Basic Pack
| Pre-Build KIT| √| √| √| √| √
Wood plate| √| √| √| √| √
Screws and Nuts| √| √| √| √| √
Sticker and user manual| √| √| √| √| √
Quick Release Connector| √| √| √| √| √
Flight Light| √| √| √| √| √
Motor| ATOMRC 2306 2000kv| | 2pcs| 2pcs| 2pcs| 2pcs
ESC| ATOMRC BLS 30A 2~4S| | 2pcs| 2pcs| 2pcs| 2pcs
Servo| ATOMRC 9g *300mm| | 4pcs| 4pcs| 4pcs| 4pcs
Prop| 7040-2| | 4pcs| 4pcs| 4pcs| 4pcs
Cam| Foxeer Toothless NANO| | | √| | √
VTX| ATOMRC Exceed TX500 VTX| | | √| | √
Antenna| ATOMRC| | | √| | √
FC| ATOMRC F405 NAVI| | | | √| √
GPS| BN220| | | | √| √
The specs will be slightly adjusted according to different,
actual specs are subject to the latest manual and real objects.
KIT Contents
KIT、PNP、FPV/Installation/KIT、PNP、FPV
- Install the V-tail on the fuselarge
- Install the V-tail servo
- Install the push rods. Install the aileron servo, push rods and servo arm cover
RTH/RTH FPV Installation
- Install the V-tail
- Installed the push rods.
- Install the INAV configurator then plug to PC
- Check INAV Configurator the receiver type,
- then assign the channel and mode
- Install the Motor, ESC and LED
ATOMRC F405 NAVI Information
Tx500 VTX User manual/TX500
- ATOMRC Tx500 VTX Wiring Diagram/TX500
VTX Setting
- Hold button 3 seconds into setting mode.
- In setting mode. short press the button to change band.
- Then hold button 3 seconds into CH setting mode, short press button to change CH.
- Hold button 3 second to get into Power setting mode, there is short bar on LED, short press to switch power, 1 bar means 25mW, 2 bar means 200mW, 3 bar means 500mW.
Band | Channel |
---|---|
1 | 2 |
Band A | 5865 |
Band B | 5733 |
Band E | 5705 |
Airwave/FS | 5740 |
Race Band | 5658 |
L Band | 5362 |
ESC Information
Throttle calibration
- The ESC included with the model has a safe start.If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position,the motor will not start untill the throttle stick is moved to the low throttle or off position.
- Power on the ESC(The ESC must connect to the motor and Receiver). The motor will emit a series of beeps, after the beeps, set the the throttle stick the the minimum, the motor will emit a series beep again. now the ESC calibration is done.
ATOMRC Exceed BLS 30A 5VBEC ESC Wiring Diagram
- Voltage input: 2~4S Lipo
- Max Current: 35A
- Output: Built in 5V 3A BEC/5V 3A BEC
- Size: 29.5 17.5mm
Please download the latest user manual at www.atomrc.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>