ATOMRC B09LCG99J2 Dolphin Plane Kit User Manual

B09LCG99J2 Dolphin Plane Kit
User Manual

www.atomrc.com/pages/download

Introduction

The Dolphin is swept forward fly wing, with elegant design, the dolphin can fly stable both on high speed and low speed, the large fuselage can give us lots of space to install the electronics, the detachable wing made the wing easy for transport, V tail made the wing more stable for crushing.

Specifications

Version Description

Dolphin Packing List

Version| KIT LITE| KIT| PNP| FPV
Description| Un—assembled KIT| | Assembled KIT| PNP version of the plane
Wood plate| | ATOMIC 2306 2000kv Motor1Pcs| Foxeer Toothless NANO
Screws and Nuts| Pre-Build KIT| ATOMIC BLS 30a ESC1Pcs
Sticker and user manual| 9g Servo300mm2Pcs| ATOMIC Exceed TX15 VTX
7040 Prop| 5.8G 2dB Antenna
The specs will be slightly adjusted according to different, actual specs are subject to the latest manual and real objects.

KIT Contents

KIT Lite Installation

1. Install the standoff and nuts, need to glue the nylon screw under the board.
   

2. Glue the GoPro mount plate, then glue the fuselage.
   

3. Install the battery strap, and glue the battery mount board to the fuselage.
   

4. Install the Camera mount plate and the V tail.
   

5. Install the side plate of the wing, then install the control horn.
   

6. Glue the plastic protection parts on the wing and the bottom.
   

7. Install the magnet on the hatch, and glue the sharp nose.
   

KIT/PNP/FPV Installation

1. Install the motor and ESC.
   

2. Install the servo and push rods, then install the rudder.
   

3. Users can choose a carbon plate to install the camera or just use foam to fill.
   

4. Install the wing to the fuselage.

5. When GoPro is installed, adjust the battery slider to adjust balance.

6. To install Gopro, use a rubber band to lock the GoPro then install the hatch.
   

7. Install the Nose and Cam.
   

8. The CG is marked under the wing, you can move the CG 3-4mm to get better control.

ESC Information

Throttle calibration

1. The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position, the motor will not start untill the throttle stick is moved to the low throttle or off position.
2. Power on the ESC(The ESC must connect to the motor and Receiver).
   The motor will emit a series of beeps, after the beeps, set the throttle stick to the minimum, and the motor will emit a series of beeps again. now the ESC calibration is done.

ESC Wiring Diagram

Voltage input/2~4S Lipo
Max Current/35A
Output/Built-in 5V 3A BEC

VTX Tx15 User manual

Tx15 Wiring Diagram

Please make sure the antenna is installed before power on, otherwise, the VTX will fry!!!

Tx15 Specs

VTX Setting

1. Hold the button 3 seconds into setting mode.
2. In setting mode. short press the button to change the band.
3. Then hold the button 3 seconds into CH setting mode, and short press the button to change CH.
4. Hold the button 3 seconds to get into Power setting mode, there is a short bar on the LED, a short press to switch power, 1 bar means 200mW, 2 bar means 800mW, 3 bar means 1500mW.

Please download the latest user manual at

www.atomrc.com/pages/download

References

• Download – ATOMRC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>