EPSOLAR EPIPDB-COM 10A Duo Battery Charging Solar Controller Instruction Manual
- June 13, 2024
- EPSOLAR
Table of Contents
INSTRUCTION MANUAL
———- Duo-battery charging solar controller, For RVs, Caravans, and
boats
———-EPIPDB-COM series
EPIPDB-COM 10A Duo Battery Charging Solar Controller
RATINGS (12/24VDC Auto)
EPIPDB-COM, 10A, 12/24VDC Auto
EPIPDB-COM, 20A, 12/24VDC Auto
NOTES: For use with solar panels only
TECHNICAL INFORMATION
Setpoint| Sealed
battery| Gel
battery| Flooded
battery
---|---|---|---
Equalize charging voltage| 14.6V| –| 14.8V
Boost charging voltage| 14.4V| 14.2V| 14.6V
Float charging voltage| 13.8V| 13.8V| 13.8V
Maximum solar voltage| 30V ( 12V System )
55V ( 24V System )
Battery voltage range| 8 15V
Boost time| 120 minutes
Self-consumption| 4mA at night. 10mA at charging
Meterbus connection| 8- PIN RJ-45
Temp. compensation| -5mV/ c /2V
Terminals| 4mm2
Temperature| -35 C +55 C
Net weight| 250g
Note: all the data is for 12V, for 24V, please use 2x.
Major feature of duo-battery controller
(Note: connect the components as the 1-6)
| Connect with the battery #1
---|---
| Connect with the battery #2
| Connect with the PV.
Remote temp. sensor
A connection point for RTS(option) to remotely monitor battery temperature
Local temp. sensor
Measures ambient temperature. Battery regulation is adjusted accordingly
For battery 1
Provides charging & battery status and errors
For battery 2
Provides charging & battery status and errors
Remote meter connection
A communication port for the remote meter
Note: where is no RTS, the controller calculate the data which got from the
local temp. sensor. The controller will come to RTS automatically when the RTS
was connected.
SETTING MODE
Three leds flashing, each LED express different specifications, choose the LED first according to the following information, and then press the switch for 5 seconds until the number flashing, choose one number as you need, and leave it and the number you set will be saved.
- 1 st led is the battery type setting.
Number shows| Battery type
---|---
1| Sealed battery
2| Gel battery
3| Flooded battery - nd 2 led is for charging priority, only set the percentage you want for battery #1, the controller will automatically calculate the rest for battery #2.
Number shows| Battery #1 charging| Battery # 2 charging
---|---|---
0| 0%| 100%
1| 10%| 90%
2| 20%| 80%
3| 30%| 70%
4| 40%| 60%
5| 50%| 50%
6| 60%| 40%
7| 70%| 30%
8| 80%| 20%
9| 90%(pre-set)| 10%
Note: in the normal charging status, the controller will divide the charging
as the setting. While battery #1 is fully charged, more charge current will be
diverted to battery #2, and return to the setting charging automatically when
the battery #1 is in low voltage.
When the controller detects there is only battery #1, all the charging will go
to the battery #1 automatically.
- rd 3. 3 led is for charging frequency.
Number shows| PWM Charging frequency
---|---
0| 25Hz(pre-set)
1| 50Hz
2| 100Hz
TROUBLESHOOTING
- LED blinking, short circuit, check the PV and battery, and make sure that they are in correct connection
- LED slowly flashing, fully charged
- LED ON, on charging
- LED frequent flashing, with battery, no charging
- LED OFF, no battery or over voltage
MECHANICAL DRAWING
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>