JBC PHB-SA Large PCB Support Instruction Manual
- June 13, 2024
- JBC
Table of Contents
JBC PHB-SA Large PCB Support Instruction Manual
This manual corresponds to the following reference:
Packing List
The following items are included:
PHBS Support …………………….1 unit
Allen key …………… 1 unit
Ref. 0013754
Manual …………….. 1 unit
Ref. 0026995
Features and Connections
Height Adjustment
PHBS Support allows adjustment for three heights between the PCB and the Heating Area of the Preheater Unit.
-
Low level
28 mm -
Medium level
38 mm -
High level
48 mm
To change the height, do as follows:
To raise the support, hold the base and pull up
To lower the support, press the button and push down.
Fast PCB Replacement
PHBS Support lets you replace PCBs of the same batch fast and easily. Use the
sliding guides to
change the PCBs.
Removing the PCB
Loosen one sliding guide, pull back and lift out the PCB.
Placing another PCB
Position it and tighten the sliding guide knobs.
Adjustable slot clamps for PCB fixation.
Reworking large PCBs
Use the 4 rubber caps to place PCBs larger than the support or thicker than 3mm.
-
Remove both guides by untightening the 8 screws.
-
Place the PCB on the 4 rubber caps.
-
The PCB is ready to work.
Maintenance
- Before carrying out maintenance or storage, always allow the support to cool down.
- Check periodically that the Support is clean, especially the axes of the sliding guide.
- Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts
- Replace any defective or damaged piece. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.
Safety
It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.
- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
- Be careful with the remains of liquid tin. In contact with the skin, it can cause burns.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the smoke produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
- This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Specifications
PHBS
Support for PCBs up to 36x28cm / 14×11” Ref. PHB-SA
-
Total Net Weight: 2.8 kg / 6.2 lb
-
Dimensions (Low Position): 432 x 514 x 78 mm
(L x W x H) 17 x 20.2 x 3.1 in -
Dimensions (High Position): 432 x 514 x 98 mm
(L x W x H) 17 x 20.2 x 3.9 in -
Max. PCB Dimensions (Between Clamps): 36 x 28 cm / 14 x 11 in
Thickness 6 mm / 0.236 in -
Total Net Weight: 2.81 kg / 6.19 lb
-
Total Package Dimensions / Weight: 595 x 520 x 180 mm / 5.01kg
(L x W x H) 23.2 x 20.5 x 7.09 in / 11.05 lb
Complies with CE standards. ESD safe.
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage
paid, to the dealer where it was purchased.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must be collected and returned to an authorized recycling
facility.
