JOYUTRY Z11PRO Wireless Charging Clock Bluetooth Speaker Instruction Manual

: June 13, 2024
: JOYUTRY

HITACHI RA-08HVQC Window Inverter Type Room Air Conditioner

Specification

Product Name: Wireless Charging Clock Bluetooth Speaker
Rated voltage: SV = 2A / 9V = 2A
Wireless charging output: SV = SW MAX/ 9V = 1 SW MAX
Speaker charging voltage: SV 1 A
Night light rated power: 2.4W(12×0.2W / LED module)
Response frequency: 70Hz~ 18KHz
Bluetooth version: VS.3
Bluetooth distance: > 1 OM
Battery capacity: 1000mAH
Product size: 0180x90mm (base 0180×11.Smm, speaker 88×80.Sx81.Smm)
Material: ABS+ PC
Executive standard: GB7000.1 GB?000.204
Form Patent Number: ZL202330114029.2

Part Name

Bluetooth speaker
Night light touch switch
Speaker function button
Speaker magnetic charging contact
TYPE-C charging port
Wireless charging base
Speaker charging indicator
Wireless charging indicator
Wireless charging center area
Wireless charging non-slip silicone
TYPE-C power supply port
TYPE-C USB cable

Installation instruction

Please connect the TYPE-C USB cable to the TYPE-C Interface of the wireless charging base.
Please connect the other end of the TYPE-C USB cable to the charging adapter. (Charging adapter is not included in this product)
a. Recommended to use a charging adapter that supports QC2.0 or QC3.0 protocol.
b. Support SW wireless charging for phone when using SV /2A charging adapter
c. Support up to 1 SW wireless fast charging when using 9V /2A or QC2.0 or QC3.0 protocol compliant charging adapter.
Please place the product on a at table and plug the charging adapter into a power outlet
After this product is connected and powered on, Wireless charging indicator is blue and night light charging indicator is red.

Speaker keys function description

Alarm key

Click: Set alarm on / off Press and hold for 2 seconds: Set alarm time and alarm music Double click: countdown timer.

Time key

Click: Adjust display brightness Press and hold for 2 seconds: Set time Double click: positive time r.

– key

Bluetooth mode click: Previous track Press and hold: turn down the volume Time mode click: Switch 12H/24H mode Alarm and time setting mode c lick: Get the current tune down Press and hold: quick downward adjustment

+ key

Combined function key

Press and hold for 2 seconds: Speaker on/off Double click: Switch bluetooth / time mode Bluetooth mode click: play/ pause music Time mode click: play/ pause white noise When the alarm clock rings, click to enter the snooze mode When phone access is available, click to answer calls and double click to reject calls When phone call is nished, click to hang up call

Use instruction

Speaker charging

a. Place the speaker to the base charging area.
b. Connect the TYPE-C USB cable to the speaker charging port. Charging indicator becomes red indica1ting the start of charging, and when fully charged, red light becomes green light. Charging time: about 3 hours to charge without being used. Music time: 3-4 hours (70% volume, lights off state)

Night light use

click to turn on the light from10% brightness to 50% brightness to 100% brightness to turn off the light.

White noise playback

Click key in time mode to enter the built-in white noise playback mode, built-in 20 music, the display shows S01-S20 accordingly. Click + and – to switch music. Press and hold+ and = key to adjust the volume, the display shows V00-V16. Click key again to exit playback.
By default, the volume is automatically adjusted to V03 after 60minutes, and the music is turned off after 90 minutes.

Speaker use

Bluetooth connection : press and hold key for 2 seconds to turn on the speaker going with a voice prompt (Power ON, Bluetooth mode), the display lights up, meanwhile bluetooth icon blinking. Open the Bluetooth in the phone setting to find the z11 Pro speaker name and click pairing. After the Bluetooth connection is successful, the Bluetooth icon on the display always goes on.
After 10 minutes of opening, if no Bluetooth connection, the Bluetooth icon on the display goes off, exiting Bluetooth mode and switching to time mode.

TWS pairing: two speakers are on, double-click + key of either speaker, you will hear the “dong” beep, after 3 seconds two speakers ring “dong” beep at the same time, which means the pairing is successful.
Double-click + key of any of the speakers again, “dong” beep will be heard, which indicating the unbinding of the TWS pairing.

Low battery reminder: When the speaker battery is low and there is a voice prompt (Low battery, please charge.), please charge it in a timely manner.

Time setting

Press and hold key for 2 seconds to enter the time setting mode, then the current time hour part blinks, click+ and – key to adjust the hour (press and hold + and = key to adjust quickly). Click then the current time minutes part blinks, click + and – key to adjust the minutes (press and hold + and – to adjust quickly). Click then complete the time setting, return to the newly set time interface. If there is no operation in 5 seconds within the hour or minute of setting time, it will be successful by default and exit to the time display state.

Attention: After the Apple phone is successfully connected to Bluetooth, the display time is synchronized with the phone time.

Display brightness setting

Click key to switch and adjust the display brightness, the initial brightness is 100%, click to switch from 100% to 70% to 45% to15% to close, click again to reach 100% brightness. Within 10 minutes without key operation, the display brightness automatically adjusts to 15% brightness, with key operation will switch back to to the original setting of brightness.

Time 12-hour system and 24-hour system settings

Click – key in time mode to switch the time display 12/24 hour system. The display shows 12H or 24H. When 12H is displayed, the icon Mil or Pi will light up accordingly to indicate AM or PM respectively.
Without any key operation, the system returns to the normal time display in 1 second.

Alarm clock settings (2 grou1ps of alarms)

Click to set the alarm clock on/off, the initial alarm clock is off.
Cl ick once to turn Alarm 1 on, then the display alarm 1 icon ( ) lights up;
Click twice to turn alarm 1 and alarm 2 both on, and the display alarm 1
icon( ) and the alarm 2 icon ( 2 ) are lit at the same time;
Click third time to turn Alarm 1 off and turn alarm 2 on, then the display alarm 2 icon ( 2 ) lights up;
Press fourth time to turn alarm 2 off.

Press and hold for 2 seconds to enter the alarm clock settings, then the display shows AL01, while the number 01 flashes. Click+ and = to switch to 02 or 01. Click n, to confirm, at the moment the hour portion of the set alarm time flashes, click + and – adjust the hour (press and hold + and = to adjust quickly).
Click to confirm, at this time the current alarm clock time of the minute part flashes, click + and – to adjust the minute ( press and hold + and = to adjust quickly).
Click to confirm, then the alarm clock music number blinks(displayed as S01- S20, alarm clock 1 initial music is No. 1, alarm clock 2 initial music is No. 2, then the music will play for 1 minute. Click + and ~ to select the alarm clock music, a total of 20 music can be selected. Click to complete the alarm clock settings, then after 1 second return to the normal time display state.

If there is no operation in 5 seconds within the hour or minute of setting time, it will be successful by default and exit to the time display state.

Attention: the two groups of alarms are set in the same way.

Alarm clock and snooze

After the alarm function is turned on, it will ring for 5 minutes when the alarm time is up, corresponding to the alarm clock 1 ( ) and alarm clock 2 ( 2 ) icon flashing, and the alarm will automatically exit the alarm and return to the time display state of there is no operation.
Click any key of the alarm other than to immediately stop and exit to the time display state.
Click to stop the alarm and enter the snooze state, then the snooze icon( ) on the display lights up. Snooze time is fixed at 5 minutes; click to enter the next snooze when the snooze alarm sounds, and press any other key to stop the alarm and exit the snooze function. Up to 12 snoozes.

Positive Timer

Double-click to enter the positive timer mode, the display shows 00:00, means 00 minutes 00 seconds, click to start positive timing, and then click again to pause. Press to reset the timing pause duration, the display shows 00:00.
The maximum time of positive timer is 99 minutes and 59 seconds. Double-click to exit the positive timer mode and return to the time state.

Countdown timer

Double-click to enter the countdown timer mode, the display shows 99:59 indicating that the initial countdown is 99 minutes and 59 seconds.
Press and hold for 2 seconds to enter the countdown timer setting, then the minutes value 99 blinks.

Click and to adjust the minutes (press and hold and to adjust quickly). Click , then the seconds value blinks. Click and to adjust the seconds （press and hold and to adjust quickly), click to start the count down.
After the countdown shows 00:00, the alarm has “tick” sound, while the display 00:00 blinks, alarming 5 minutes. Click to stop the alarm when it sounds. During the countdown, click to pause. Press and hold to reset the countdown pause duration, then the display shows 99:59.

Double-click during countdown to exit the countdown timer mode and return to the time state.

The bottom of the speaker has a magnetic function

Which can be directly adsorbed on iron objects. If there are no ferrous objects, please install them with the iron accessories included with the product.

Wireless phone charging

a. Place the mobile phone with wireless charging function in the wireless charging center area of the base, when the blue light of the wireless charging indicator turns white, please start charging your phone.
b. If there is no charging, please adjust the position of your phone or check whether your phone has wireless charging function.
c. When the wireless charging indicator light ashes rapidly (foreign object reminding function), please check the phone shell or whether there are metal objects between the phone and wireless charger.
Special reminder: please remove the iron sheet before using the wireless charging function, which cannot be used if the mobile phone is affixed with the magnetic iron sheet of the car bracket.

Caution

Please don’t place other metal products in the base wireless charging area.
Please use a power adapter with an output voltage of DC 5V/2A or DC 9V/2A, adapter that complies with QC2.0, QC3.0 protocols
Please align and fully contact the wireless charging product with the base wireless charging center area to achieve the best charging effect.
Please don’t use non-nominal voltage for charging.
Please keep product away from heat sources for containing lithium battery.
Please charge it at least every 3 months in order to ensure the effective service life of the night light battery

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.