ANSMANN TYPE 2 Electric Vehicle Charging Cable User Manual
- June 13, 2024
- ANSMANN
Table of Contents
ANSMANN TYPE 2 Electric Vehicle Charging Cable
Product Information
The product is an Electric Vehicle Charging Cable. It is a Type 2 | Mode 3
cable with a power rating of 22kW and an output of 32A. The cable is designed
to be used with electric and hybrid vehicles for charging purposes. It comes
with a storage bag and an instruction manual. The product meets the
requirements of the EU Directive.
Technical Specifications
- Rated Voltage: 400V AC 50Hz
- Rated Power: 22kW
- Vehicle Plug: IEC62196-2 Typ 2 -lle
- Infrastructure Plug: IEC62196-2 Typ 2 -llb
- No. of Phases: 3-phasig
- Output: 32A
- High Voltage Resistance: 2600V AC
- Contact Resistance: 0.3m (L/N)
- Isolation Resistance: 500M (1000V AC)
- Resistor Coding: 220
- Charge Mode: IEC 62196-2, IEC 61851-1
- Contact Thermal Rise: 50K
- Protection Type: IP55 (in gestecktem Zustand)
- Working Humidity: 5% – 95% non-condensing
- Withdrawal Force: 45N / 80N
- Flammability: UL94 V-0
- Operating Temperature:
- Pluging Cycles: 10000x (Lastfrei)
- Cable Weight: 5m: 3.2 kg | 7.5m: 5.25 kg
Product Usage Instructions
Follow the steps below to use the Electric Vehicle Charging Cable:
- Make sure to read and follow the operating instructions of both the charging station and the electric vehicle.
- Turn off the vehicle and put the gear lever in the park.
- Start the charging process at the charging station. The charging connectors will automatically lock.
- Refer to the operating instructions at the charging station to prematurely end the charging process if needed.
- After the charging process is complete, the charging connectors will automatically unlock.
- Disconnect the charging connectors from both the charging station and the electric vehicle (make sure the vehicle is unlocked).
- Put the protective caps on both charging connectors and roll up the cable without bending it.
- Store the cable in a clean place.
Environmental Information / Disposal
Dispose of the unusable product in accordance with legal requirements.
SCOPE OF DELIVERY
- 22kW charging cable for electric vehicle
- Storage bag
- Instruction manual
First unpack the product and check it for completeness and damages. Do not operate the product if it is damaged. Contact your retailer should you find any damage to the product.
INTENDED USE
Only use the cable for charging electric and hybrid vehicles with alternating current (AC) at charging stations. The cable may only be used together with standard-compliant and designated vehicle inlets according to IEC 62196-2 (type 2 plug). Compliance with all the information in these operating instructions is also part of the intended use. Any other use or use beyond this is considered misuse and can lead to dangerous situations. The user is liable for any damage caused by improper use.
SIGNS AND SYMBOLS
Please take note of the following symbols and words used in the operating
instructions, on the product, and on the packaging:
SAFETY INSTRUCTIONS
- Carefully read the entire instruction manual before first operating the product.
- It contains important information on handling the product. If you give the product to third parties, you must include this instruction manual.
- Keep children away from the product and the packaging. The product is not a toy.
- Children should be supervised to ensure that they do not play with the product.
- This product complies with protection class IP55 (plugged in).
- Never touch the product with wet or damp hands.
- Safe operation cannot be guaranteed if the product shows any kind of damage. If the product is damaged, it must be disposed of or repaired.
- Do not repair the product yourself! Have repairs carried out by a professional electrician.
- Never immerse the product in water or other liquids. Never grasp a unit connected to a power supply if it has fallen into the water.
- Failure to observe the safety instructions may result in damage to the unit or dangerous injury to persons!
- This product is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge in handling the product. Such persons must first be instructed by a supervisor responsible for their safety or supervised during product operation!
- Improper handling of the charging cable can cause explosions, electric shocks, and short circuits. The generally applicable safety precautions and the instructions must be observed.
- Before each use, check the charging cable and the contacts for damage and dirt.
- Never charge with a damaged charging cable or damaged vehicle inlet. Never charge with contacts that have become dirty or damp.
- Never pull off the plugs with force. Dangerous electric arcs can cause death or serious injury.
- Only connect the charging cable to vehicle inlets and infrastructure charging sockets that are protected from water, direct sunlight, moisture, and other liquids.
- There are electric vehicles that allow the vehicle to be started with the charging cable plugged in. Always make sure to disconnect the charging cable before driving off.
- Never use the charging cable with an extension cable or an adapter.
- Modifications or alterations are dangerous to life and lead to immediate exclusion of the warranty.
TECHNICAL DATA
- Rated voltage: 400V AC 50Hz
- Rated power: 22kW
- Vehicle plug: IEC62196-2 Typ 2 -lle
- Infrastructure plug: IEC62196-2 Typ 2 -lb
- No. of phases: 3-phase
- Output: 32A
- High voltage resistance: 2600V AC
- Contact resistance: ≤0.3mΩ (L/N)
- Isolation resistance: 500MΩ (1000V AC)
- Resistor coding: 220Ω
- Charge mode: IEC 62196-2, IEC 61851-1
- Contact thermal rise: ≤50K
- Protection type: IP55 (plugged in)
- Working humidity: 5% – 95% noncondensed
- Withdrawal force: 45N / 80N
- Flammability: UL94 V-0
- Operating temperature: -25°C – +55°C
- Plugging cycles: ≥10000x (no load)
- Cable: 5×2,5mm² + 1×0,75mm²
- Weight: 5m: 3,2 kg / 5,25m: kg
OPERATION
Observe the operating instructions for the charging station and the electric vehicle.
- Switch off the vehicle. Go to parking mode.
- Remove the protective caps from the charging plugs and connect the infrastructure charging plug to the infrastructure charging socket and the vehicle charging plug to the vehicle inlet. Ensure the correct assignment and check that the plug connections are correctly and completely plugged in.
- Start the charging process at the charging station. The charging plugs are automatically locked.
- To end the charging process prematurely, follow the operating instructions of the charging station.
- After the charging process is finished, the charging plugs are automatically unlocked.
- Disconnect the charging plugs from the charging station and the electric vehicle (the EV must be unlocked).
- Put the protective caps on the charging plugs and roll up the cable without kinks.
CHARGING TIME
The duration of the charging process depends on the capacity, the state of
charge of the high-voltage battery of your vehicle, and the permissible
charging power of the charging cable. The charging current (max. 32A) is
regulated by the EV. At very low and very high temperatures, the charging
performance may be impaired.
CLEANING
Only clean the cable when it is not connected to the vehicle or the socket.
Clean the charging cable and the dirty contacts only with a dry cloth. Never
use harsh detergents, water, or steam cleaners. Never immerse the item in
liquids. Store the charging cable with the protective caps on in a dry and
clean place.
DISPOSAL
At the end of its service life, dispose of the cable in keeping with all legal
requirements. The dustbin symbol indicates that waste electrical and
electronic equipment may not be disposed of with normal household waste within
the EU. Please use local recycling and collection points or contact the
retailer where you purchased the product. You thus fulfill your statutory
obligations and contribute to the protection of the environment.
DISCLAIMERS
The information contained in this instruction manual is subject to change
without prior notice. ANSMANN assumes no liability for direct, indirect,
accidental, or other types of damage or consequential damage that result from
improper handling of the product or failure to comply with the information
contained in this instruction manual. We assume no liability and grant no
warranty claims in cases of improper use of the product.
WARRANTY INFORMATION
We offer a two-year warranty on the product. Damages to the product due to failure to observe the instruction manual will void the warranty. This does not affect your legal warranty right. You can find our warranty terms online at www.ansmann.de.
Germany
Support & FAQ: ansmann.de
E-Mail: hotline@ansmann.de
Hotline: +49 (0) 6294 / 4204 3400
MA-1900-0119+1900-0120/V01/12-2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>