YAKIMA SkyRise Medium Review Instruction Manual

: June 13, 2024
: YAKIMA

Table of Contents

CONTENTS
IMPORTANT FIT INFORMATION
ASSEMBLE AND INSTALL
REMOVAL
WEIGHT LIMITS
IMPORTANT WARNINGS
ROOF-TOP TENT CARE AND MAINTENANCE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SkyRise™

YAKIMA SkyRise Medium Review - cover

Visit www.yakima.com/skyrise to determine which roof-rack is required to use SkyRise™ with your vehicle.

WATCH FOR THESE SYMBOLS!
= Keep safe by reading the important safety warnings included in the product instructions! Safety warnings are identified with this symbol.
= Please read all important product notes in the product instructions to ensure proper installation or fit information. These notes are identified with this symbol.

SOME DO’S AND DON’TS (additional warnings are contained in these instructions)

Do have a friend or dealer help with installation.
Do use the tent when parked on level ground.
Do remove the tent when not in use.
Do dry the tent before storage.
Do use the tent on level ground.
Do close the tent cover fully before driving away.
Do assist children on the ladder.
Do close and secure the cover before driving.
Do not climb on your vehicle’s roof.
Do not use the tent unless ladder is securely in place.
Do not allow more than one adult on the ladder at a time.
Do not use the tent in high-winds or heavy-snow.
Do not transport anything on top of the closed tent.
Do not use an open flame nor cook inside tent.

IMPORTANT FIT INFORMATION

WARNING: DO NOT USE THIS PRODUCT ON A VEHICLE THAT IS INDICATED AS “NO-FIT”.
The Yakima Fit-List now includes approved SkyRise™ fits for many popular vehicles. Updates and additions to the Yakima Fit-List for rooftop tents are being made continually. Please go to fitlookup.yakima.com for latest updates.
Vehicles that we have seen and tested are designated as “FIT” or “NO-FIT” for SkyRise™. Fits for SkyRise are different than for other Yakima products. Please note that virtually all factory crossbars are too flexible for rooftop tents. So vehicles approved in the Fit-List will still require a Yakima roof- rack system. |f we have not tested your particular vehicle and rack system, you can use the checklist below to evaluate whether your vehicle and rack system may support a SkyRise.
Remember, the checklist below is designed to be a guideline only and any installation not on our approved Fit-List is at the sole risk and responsibility of the owner or installer.

The vehicle and rack system have a minimum load carrying capacity of 165 lbs.
The following Yakima towers may be used: TimberLine™ SkyLine™, RidgeLine™, RailGrab™ (med. or large claw), ControlTower™, LowRider™, 1A Raingutter™, BedRock™ and Outdoorsman™
You may use Skykise with Yakima RoundBar™, CoreBar™, or JetStream bars™.
For factory-tracks or fixed-points (see figure 1), ensure that the roof does not deform when heavy loads are applied.
For vehicles with raised-rails, position the crossbars as close as possible to rail supports.
Ensure that the crossbar spread is between 26′ and 40.5″,
Do not use a rooftop tent with any clamp type towers (including Q-Tower™ and BaseLine™) or RailGrab™ Towers with Small Claw or Pin Adapters.
Do not use with factory-crossbars, they are too flexible.
Do not position the mounting hardware more than 1’ outside of the Tower (see figure 2).
The maximum distance from top of the crossbar to the ground for SkyRise Small is 86″ and 98″ for SkyRise Medium.
Do not install SkyRise™ on cantilever rails or rails without sufficient support (see figure 3).

ASSEMBLE AND INSTALL

REMOVE THE CONTENTS FROM THE TENT.
Remove the ladder, cover, rainfly rod bag, and mounting hardware box from inside.
OPEN THE TENT.
Lift the side of the tent with the mounting holes into the vertical position, as shown below.
DETERMINE THE TENT DEPLOYMENT DIRECTION.
Identify the mounting holes for your deployment direction and use them in the next steps.
PREPARE THE MOUNTING CLAMPS.
Use the 5 mm hex wrench to loosen the slider-bolt.
Slide 2 square nuts into each mount and align the mounts with the predrilled holes in the tent floor. Refer to step 2 for orientation.
ATTACH THE MOUNTING CLAMPS.
Reach under the mattress, and feed a bolt through the hole.
Slide the square nut using the included 5 mm hex wrench to align it with the bolt end. Hand-tighten the bolt from inside the tent, ye then tighten the bolts down completely with the hex wrench.
TIPS
• Have a friend help hold the tent steady.
• Remove the mattress completely for easier access to the holes.
Be sure the knobs all face the same. direction and that the locks are on the same side facing outboard (refer to the mount setup in step 2).
ATTACH THE LADDER BRACKETS.
First, flip the SkyRise™ over to rest on the clamps. Then locate the predrilled holes under the stickers near the edge, and remove the stickers.
Orient the brackets as shown, then reach under the mattress and insert 2 of the long bolts with washers up through the floor and bracket. Hand-thread a locknut onto each bolt. Then, using the 8 mm hex wrench and included 13 mm open-ended wrench, tighten the bolts.
ATTACH THE LADDER.
Make sure the information stickers are visible, and the top brackets are oriented with the FLAT EDGE DOWN. Secure the ladder with the short bolts, washers, plastic bushings, and lock nuts as shown. Use the 8 mm hex wrench and 13 mm open-ended wrench to tighten the hardware to 2./5 Nm. BE SURE THE BOLTS ARE FULLY TIGHTENED!
INSTALL THE COVER.
A. Slide the cover (Velcro™-side-up) into the round channel.
B. Secure the tent with its Velcro ties, being sure not to over-tighten.
C. Put the cover on, secure the buckles, and zipper closure.
PREPARE THE TENT FOR VEHICLE INSTALLATION.
A. Measure the distance (X) between the crossbars on your vehicle from the center of the front bar to the center of the rear bar.
B. Tilt the SkyRise™ up on its side and open all the clamps completely. Set the distance between the clamps by sliding them along their tracks so they will match up with your
crossbar spread (X). Be sure to measure from the fixed side of the clamps (X). Once set, partially tighten all slider bolts.
If you have Yakima RoundBars™, you must use the included RoundBar adapters. The adapters go around the RoundBars, and the clamps fit over the adapters. Make sure to remove the rubber pads from the clamps.
INSTALL THE TENT ON YOUR VEHICLE.
Test the installation and retighten as necessary.
You are now ready to travel to your campsite!
Find a level place to park and apply your parking brake.
REMOVE AND SECURE THE COVER.
Unzip and Unbuckle the cover, fold it forward, then roll it up and secure it with the ties.
Then release the Velcro™ straps.
DEPLOY THE TENT AND SET THE LADDER.
A First, release the strap, then grasp the ladder from the bottom rung, and pull it to extend the ladder out.
B Push down on the ladder and walk backwards a couple steps. This will force the SkyRise™ to fold out and open up.
C With a secure grasp on the ladder, use it to fully lower the SkyRise™ until it’s open and the floor of the tent is flat. Rest the feet of the ladder on the ground.
D
• Make sure the top rung is locked out in one of the 3 positions (listen for a “click” as each rung locks into place).
• Adjust the ladder so that the tent platform is level.
• The ladder angle must be between 90° and 75°.
• Unused rungs should be stacked under the top step of the ladder.
• SkyRise™ is not compatible with ladder extensions.
• The ladder must remain in place to support the tent.
• Do not retract the ladder while it’s in use.
• Read and follow the warnings on the ladder.
• Use caution while climbing up and down the ladder.
SET UP THE RAINFLY.
The easiest way to deploy the rainfly is from within the tent. With the rainfly attached to the tent, climb inside, and open the doors and side windows.
Reach through the side windows and find the 2 flaps on each side of the tent. Place the straight ends of 4 rods into the holes beneath the side flaps and hook the curved ends into the grommet holes on the rainfly.
Reach through the doors and find the 2 flaps on each end of the tent. Place the straight ends of the other 4 rods into the holes beneath the end flaps and hook the curved ends into the grommet holes on the rainfly.
The rods are under tension when installed; do not be directly under a rod while installing or removing them. The rainfly is removable. It can be detached from the tent by unhooking the buckles and then lifted away with the rainfly hoops.
In windy conditions, use the included ground stakes and tie-downs to anchor your SkyRise™. Tie them to the D-rings found on the frame as shown below.
Use the SkyRise™ Medium image below as a guide.

CLOSE AND SECURE

CLOSE THE TENT.
Use the ladder to fold the tent back onto itself.
Collapse the ladder and fully retract it. Secure the Velcro™ straps. Unroll and replace the protective cover, zip it closed, and buckle it up.

Never operate your vehicle with the SkyRise™ open! You must close and secure your SkyRise before driving.

REMOVAL

REMOVE THE TENT.
A. Unlock the clamps.
B. Fully open clamps.
C. With the assistance of a friend, remove the SkyRise™ from your vehicle.

WEIGHT LIMITS

Do not exceed your vehicle’s weight limits.

MAXIMUM TENT CAPACITY:
SkyRise™ Small : 400 Ibs.
SkyRise™ Medium: 600 Ibs.
SkyRise™ HD Small: 400 Ibs.
SkyRise™ HD Medium: 600 Ibs.

WEIGHTS OF TENTS:
SkyRise™ Small = 95 Ibs. (43 Kg)
SkyRise™ Medium = 115 Ibs. (52 Kg)
SkyRise™ HD Small = 100 Ibs. (45 Kg)
SkyRise™ HD Medium = 120 Ibs. (54 Kg)

YAKIMA SkyRise Medium Review - ASSEMBLE AND INSTALL 26

IMPORTANT WARNINGS

Remove your tent and Yakima rack before entering an automated car wash.
Do not use fuel-burning or oxygen-consuming devices inside the tent. These include candles, gas lanterns, kerosene lamps, stoves, and cooking and heating appliances.
Do not pitch the tent near a campfire or any other flame source.
Inspect the mounting hardware of the tent before driving away.
Never extend the ladder beyond the predrilled holes and factory-locking position.
Do not drill additional holes into the ladder.
The ladder angle must be between 90° and 75°.

Rack Installation
Improperly mounted roof-racks and tents can come loose during travel and cause serious accidents! Installation, handling, and use must be carried out in accordance with product and roof rack instructions.
Check the attachment hardware and the load to make sure everything is secure.

Before driving away
After driving a short distance, following tent install
At regular intervals on longer trips
Every 2 hours on bad terrain

Vehicle Driving and Regulations
The speed driven must be suited to the load transported and to official speed limits. When transporting any load, the speed of the vehicle must take into account all conditions such as the state of the road, the surface of the road, traffic conditions, wind, etc. Vehicle handling, cornering, braking, and sensitivity to side winds will change with the addition of rooftop loads.

ROOF-TOP TENT CARE AND MAINTENANCE

Your Yakima rooftop tent is designed to be a durable companion on your adventures.
In order to keep it performing at its best, we recommend some simple care and maintenance steps that will help prolong the life of your rooftop tent.

Prior to each use, inspect your rooftop tent mounting hardware. If necessary, clean with a solution of mild detergent and water. Periodically lubricate the threads on
your hardware with a light, synthetic bicycle lubricant to maintain performance.
Dry your rooftop tent thoroughly before you close it. If unable to properly dry your rooftop tent prior to closing, open it up and air-dry it at your next opportunity.
Failure to properly dry out your tent can lead to the growth of mold and mildew, which can degrade the tent material, causing discoloration and foul odor. Mold and mildew growth is not covered under your rooftop tent warranty.
Proper storage of your rooftop tent when not in use will prolong its life. Ensure tent is fully dry prior to storage, and store it in a cool, dry location free from direct sunlight.
Zippers should be pulled with even force and in gentle fashion. Never force a zipper open or closed as it may damage the zipper. Keep your zippers free from dust and dirt, and periodically apply non-scented bees wax to the zipper-teeth as lubrication. This will prolong the life of your zippers.
The ladder should be wiped free of any dirt or dust prior to collapsing the tent.
Periodically wipe down the aluminum telescoping side rails of the ladder with silicone spray anda cloth. DO NOT spray silicone spray directly on the ladder tread surfaces.
Keep your mattress dry and free from dirt. Prior to closing your rooftop tent, lift your mattress and ensure the underside is dry. Remove mattress and air-dry if necessary.
To clean the mattress cover, remove it and machine wash on the gentle-cycle setting with Woolite™ detergent. Then hang-dry. DO NOT TUMBLE-DRY.
To clean your rooftop tent, use a mild detergent and warm water gently applied with a sponge. Rinse with a clean wet sponge and allow to dry thoroughly.
If mildew and/or mold have begun to grow on your tent, we recommend cleaning the affected tent fabric by sponging-on a solution of 1 cup Lysol™ mixed in 1 gallon of hot water and allowing it to dry. Next, prepare a solution of 1 cup lemon juice concentrate and 1 cup salt in 1 gallon of hot water. Sponge this solution directly into the affected areas to rinse out the Lysol solution. Then allow it to air-dry completely.
Taking these steps will stop the growth of the mildew and help eliminate odor; however, they may not completely remove the stains.
Avoid excessive sun exposure to your tent to prolong the life of the fabric. Over time, UV rays can degrade tent fabric and waterproof coatings. If your rainfly material begins to break down due to exposure and use, we suggest washing the fabric with mild detergent and water, followed by a treatment of a water repellent such as 303 Fabric Guard™ Consult your local outdoor store for other tent fabric-care products . and use as directed.