Sensio SE79095 Link-S Receiver Magnet and Reed Switch Instruction Manual
- June 13, 2024
- Sensio
Table of Contents
INSTALLATION
INSTRUCTIONS
Link-S – Receiver, Magnet and Reed
Switch
Lighting Control
Product Codes:
SE79095 – Link-S – Receiver, Magnet and Reed Switch
SE79195 – Link-S – Receiver
SE79295 – Link-S – Magnet & Reed Switch
IMPORTANT: Please read these instructions before commencing installation
and retain for future reference.
Components
Tools Required
Important Safety Information
Please read these instructions carefully before attempting to install this
product. It is advisable to keep these instructions in a safe place for future
reference.
We recommend that you consult a qualified electrician. All electrical
installation must be carried out in accordance with current IEE wiring
regulations (BS7671).
These products must not be modified, if any modification are made, it may
invalidate the warranty and may render the product unsafe. These LED lights
operate low voltage (24V).
- Install on smooth flat surface(s) only.
- Do not exeed or stretch the cable length of each wire.
- This product is IP20 Rated.
Technical Specification
Link-S — Magnet and Reed Switch
Input Voltage| 3V ( 2x 1632 button Batteries)
Standby Current| 1.8uA
Transmitting Frequency| 433.29Mhz
Transmitting Current| 8mA
Range| >8m
Operating Temperature| -5°C to 40°C
Humidity| 5% to 85% Non Condensing
Link-S – Receiver
Input Voltage| 24V
Max Power| 72W
Range| >8m
Sensitivity| 98dBM
Standby Power| ≤0.15W
Operating Temperature| -5°C to 40°C
Humidity| 5% to 85% Non Condensing
Safety Instructions
- This product is only suitable for connecting to Sensio LED lights and fitings.
- Always read the installation guide of any product used in conjunction with this product.
- Never exceed the total output of a LED driver or receiver.
- Suitable for furniture lighting.
- Class III safety extra low voltage (SELV).
Waste Electrical & Electronic Equipment (WEEE)
The symbol on the product, or on the document accompanying the product, the
crossed out wheelie bin symbol, indicates that this product may not be treated
as household waste.
Instead it shall be handed over to the applicable collection point for the
recycling of electrical andelectronic waste.
Installation
Peel the
adhesive backing tape off of the Reid switch and stick it in your desired
location.
Note: The product is suitable for installation in many scenarios, please
ensure that you measure and plan before installation.
Peel the adhesive backing tape off of the magnet and stick it into a position
where it will make contact with the Reid switch when the doors are closed.
Note: The magnet can make contact with the side of the Reid switch.
Connect the male-ended cable from the receiver into the LED Driver.
Connect your light to the
receiver by inserting the male-ended JB4 cable into the female-end.
Secure the receiver in position using the screws included. Finally, connect
the driver to the mains supply.
If you are installing a Sensio Wireless Magnetic Contact and Receiver with
multiple Reid switches and magnets, simply follow stages 1 and 2 for
installaton. Once installed, each switch will trigger the lighting when the
two components break contact.
Operation
Each receiver can
connect with up to five magnmagnets and reed switches. The recommended scenario
for this setup would be to have a magnet and reed switch on a series of
cabinet doors. Opening each cabinet door would then trigger all the lights
connected to the receiver.
For example, a series of in-cabinet lights.
EEach magnet and reed switch can be connect with up to five different receivers.
The recommended scenario for this setup would be to install the magnet and
reed switch on the door to a room. Opening the door will then trigger all the
lights connected to the receivers.
For example, all of the lighting in that room.
Maintenance & Care
- Ensure that the power is disconnected prior to cleaning.
- To keep the finish of this product, wipe over with soft cloth periodically.
- Do not use harsh chemical solvents, this may dis-colour or damage the finish.
- Do not over-tighten screws on the terminal block.
UK Address: Sensio Ltd, Unit 7, Speedwell Road, Castleford, West Yorks, WF10
5PY
EU Rep.: Sensio Lighting Dublin Ltd, The Black Church, St. Mary’s Place,
Dublin, Ireland, D07 P4AX
Sensio House, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire,
WF10 5PY
www.sensio.co.uk
Technical drawings for illustration purposes only, Sensio has the right to
change any information without prior notice.
Sensio V3
Sensio – V4
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>