JBC JT-T1A JTT Heater Hose Set Instruction Manual
- June 13, 2024
- JBC
Table of Contents
JBC JT-T1A JTT Heater Hose Set
Product Information
| Product Name | JTT Heater Hose Set |
|---|---|
| References | JT-T1A (100V/120V), JT-T2A (230V) |
| Packing List | Handle for JTT (Ref. JT-A) – 1 unit |
Manual – 1 unit (Ref. 0029044)
JTH Heating Element for JTT – 1 unit (according to purchased
reference, either JTH1 Ref. 0014105 (100V/120V) or JTH2 Ref.
0014107 (230V))
Features| JTT Heater Hose Set allows for the repair of medium and large
SMDs. It works with the JTSE Control Unit and JN Nozzles.
Specifications| Hose Length: 1100 mm / 43.31 in
Total Net Weight: 370.5 g / 0.817 lb
Package Dimensions/Weight: 382 x 159 x 81 mm / 508.8 g (L x W x
H)
Compliance| Complies with CE standards. ESD safe.
Warranty| JBC’s 2-year warranty covers this equipment against all
manufacturing defects, including the replacement of defective parts
and labor. The warranty does not cover product wear or misuse. To
validate the warranty, the equipment must be returned, postage
paid, to the dealer where it was purchased.
Disposal| This product should not be thrown in the garbage. In accordance
with the European directive 2012/19/EU, electronic equipment at the
end of its life must be collected and returned to an authorized
recycling facility.
Product Usage Instructions
Changing JTT Heater Hose Set:
Note: Only perform this operation when the station is turned off.
- Use a spanner to unscrew the nut (1) and remove the tool hose (2).
- Insert the new hose, making sure it is pushed all the way into the connector (2), and tighten the nut (1).
Replacing the Heating Element:
Note: Only perform this operation when the heating element is cold and the unit is disconnected from the mains.
- Loosen the screw (1) and pull the worn heating element out of the handle (2).
- Insert the new heating element, making sure it is pushed all the way in (2), and tighten the screw (1).
This manual corresponds to the following references:
- JT-T1A (100V/120V)
- JT-T2A (230V)
Packing List
The following items are included:
- Handle for JTT 1 unit Ref. JT-A
- Manual 1 unit Ref. 0029044
JTH
Heating Element for JTT 1 unit according to purchased reference included
either JTH1 Ref. 0014105 (100V/120V) or JTH2 Ref. 0014107 (230V)
Changing JTT Heater Hose Set
Note: Only perform this operation when the station is turned off.
Use a spanner to unscrew the nut (1) and remove the tool hose (2).
Insert the new hose, make sure it is pushed all the wayinto the connector (2), andtighten the nut (1).
Features
JTT Heater Hose Set allows to repair medium and large SMDs. It works with JTSE Control Unit and JN Nozzles.
Replacing the Heating Element
- Note: Only perform this operation when the heating element is cold and the unit is disconnected from the mains.
- Loosen the screw (1) and pull the worn heating element out of the handle (2).
- Insert the new heating element, make sure it is pushed all the way in (2) and tighten the screw (1).
Specifications
JTT
Heater Hose Set
- Ref.: JT-T1A (100V/120V)
- Ref.: JT-T2A (230V)
- Hose Length: 1100 mm / 43.31 in
- Total Net Weight: 370.5 g / 0.817 lb
- Package Dimensions/Weight: 382 x 159 x 81 mm / 508.8 g
- (L x W x H) 15.04 x 6.26 x 3.19 in / 1.122 lb
Complies with CE standards. ESD safe.
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased
This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility