Inglesina 360 Aptica System Quattro Instruction Manual

Inglesina 360 Aptica System Quattro

Product Information

• Product Name : Aptica System Quattro
• Languages available in the user manual : Polish, Romanian, Croatian, Slovenian, Albanian, Czech, Hungarian, Serbian, Italian, English, German, Dutch

**Product Usage Instructions

**

• Ensure that the product is properly assembled and all components are correctly attached.
• Make sure that the frame is fully opened and all locking mechanisms are engaged.
• Check that the bassinet, stroller seat, or car seat are securely attached by pulling them upwards.
• Do not use the product for purposes other than those explicitly stated in the user manual.
• Follow the instructions provided in the user manual for proper usage.
• Do not have the product repaired at unauthorized service centers.
• Avoid negligence or mishandling that could cause damage to the product.
• Expect normal wear and tear on wheels, moving parts, and fabrics with prolonged and continuous daily use.

WARNING

• IMPORTANT – READ CAREFULLY AND KEEP FOR FUTURE REFERENCE. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN JEOPARDISE THE SAFETY OF YOUR CHILD.
• YOUR CHILD’S SAFETY IS YOUR RESPONSIBILITY.
• WARNING! NEVER LEAVE THE CHILD UNATTENDED : IT CAN BE DANGEROUS. PAY UTMOST CARE WHEN USING THE PRODUCT.
• TO PREVENT THE BABY FROM FALLING AND/OR SLIDING OUT WITH SERIOUS INJURY RISKS, ALWAYS USE THE SAFETY BELTS PROPERLY FASTENED AND ADJUSTED.

CARRYCOT
This product is suitable for babies from birth up to 9 kg.

SEAT UNIT

• According to EN 1888-2:2018 + A1:2022 this product is suitable for babies from birth up to 22 kg or 4 years, whichever comes first.
• The product is approved for children up to 22 kg with forward-facing stroller seat. The stroller seat should be used rear facing in the child’s first few months of life and in any case not beyond 15 kg.

INFANT CAR SEAT

• This product is suitable for babies from birth up to 13 kg.
• The carrycot and/or stroller seat backrest should be adjusted to their most reclined position when used with newborn children.
• The Aptica Inglesina chassis must be used only in combination with the corresponding All Season stroller seat, the Maxi Aptica Carrycot, and Cab 0+ or Darwin Infant or Darwin Infant Recline car seats. If in doubt, check the inglesina.com website or contact an Authorised Retailer or Inglesina Customer Services.

STROLLER – TRAVEL SYSTEM

• WARNING NEVER LEAVE THE CHILD UNATTENDED.
• WARNING ENSURE THAT ALL THE LOCKING DEVICES ARE ENGAGED BEFORE USE.
• WARNING TO AVOID INJURY, ENSURE THAT THE CHILD IS KEPT AWAY WHEN UNFOLDING AND FOLDING THIS PRODUCT.
• WARNING DO NOT LET THE CHILD PLAY WITH THIS PRODUCT.
• WARNING ALWAYS USE THE RESTRAINT SYSTEM.
• WARNING THIS PRODUCT IS NOT SUITABLE FOR RUNNING OR SKATING.
• THIS PRODUCT IS ONLY SUITABLE FOR WALKING USE.
• WARNING CHECK THAT THE PRAM BODY OR SEAT UNIT OR CAR SEAT ATTACHMENT DEVICES ARE CORRECTLY ENGAGED BEFORE USE.
• TO PREVENT ACCIDENTS, ENSURE THAT THE VEHICLE IS KEPT AWAY FROM AUTOMATIC CLOSING DOORS (E.G. ON TRAINS, LIFTS).
• Avoid serious injury from falling or sliding out. Always use the restraint system and adjust it properly.
• The correct use of the harnesses restraint system is not a substitute for proper adult supervision.
• Be aware that the bumper bar is not a restraint. Always use the harnesses restraint system.
• Do not lift the stroller by the bumper bar as it may disengage.

CARRYCOT

• THIS PRODUCT IS SUITABLE FOR A CHILD WHO CANNOT SIT UP BY ITSELF, ROLL OVER AND CANNOT PUSH ITSELF UP ON ITS HANDS AND KNEES. MAXIMUM WEIGHT OF THE CHILD: 9 KG.
• DO NOT LET OTHER CHILDREN PLAY UNATTENDED NEAR THE CARRYCOT.
• DO NOT USE IF ANY PART OF THE CARRY COT IS BROKEN, TORN OR MISSING.
• Do not use or add any mattress other than that provided with the carrycot or approved by the Manufacturer.
• SUFFOCATION HAZARD : Infants can suffocate. Always make sure there is enough room around your baby’s face such that the airflow is not obstructed. Strings can cause strangulation. Do not place items with a string around the child’s neck, such as hood strings or pacifier cords. Do not suspend strings over the product or attach string to toys. Keep soft objects, stuffed toys, bumpers and positioners away from the carrycot because they may be dangerous.
• Inglesina Maxi Aptica carrycot can be used with Inglesina Standup.
• The head of the child in the carrycot should never be lower than the body of the child.
• Before carrying or lifting the carrycot, always check that the handle is in its vertical position and properly locked on both sides.
• Before carrying or lifting the carrycot, always check that the backrest is adjusted in the lowest position.
• Make sure that the carrycot is correctly attached to the chassis before use by pulling the handle upwards.
• The carrycot can be used as a child restraint device for car transportation only when fitted with the suitable Inglesina Vehicle Kit (Kit Auto Maxi).
• The restraint system of the Vehicle Kit shall be removed or hidden when the product is used outside car for unattended sleeping (refer to the Vehicle Kit manual).
• The handle and the bottom of the carrycot should be inspected regularly for signs of damage and wear.

USING THE CARRYCOT INDEPENDENTLY OFF THE CHASSIS

• THIS PRODUCT IS ONLY SUITABLE FOR A CHILD WHO CANNOT SIT UP UNAIDED.
• ONLY USE ON A FIRM, HORIZONTAL LEVEL, FLAT AND DRY SURFACE.
• FALL HAZARD : Child’s movement can slide the product. Never place the product near edges of counter tops, tables, or elevated surface.
• SUFFOCATION HAZARD : the product can roll over on soft surfaces and suffocate child. NEVER place the product on beds, sofas, or other soft surfaces.

SAFETY

• Before assembly, ensure that the product and all its components have not been damaged during transport. Should this be the case, do not use the product and keep it out of reach of children.
• For the safety of your child, remove and eliminate all plastic bags and elements belonging to the packaging before use and, in any case, keep them out of reach of newborns and children.
• This product must be used to accomodate only one child.
• Before use
  • Make sure that the product is properly assembled, that all its components are properly fastened and that all the mechanisms are engaged. Make sure that the lining is properly secured to the structure.
  • Make sure that the chassis is fully open and ensure that all the locking devices are engaged.
  • Make sure that the pram body, seat unit or car seat are correctly attached by pulling them upwards.
• Avoid finger entrapment, take care when folding and unfolding the product. Carefully follow the sequences indicated in the pictures in the manual.
• Do not open, fold or disassemble the product with the baby inside.
• In any case, be particularly careful when performing these tasks with the child nearby.
• Finger entrapment and scissoring actions may happen during these operations.
• Always make sure that the brake is engaged when positioning the child into the stroller seat/carrycot or taking him/her out, as well as during stops, and when assembling/disassembling any accessory.
• Always use the parking brake, even when standing still for only a few moments.
• When parking check if the brake is properly engaged by moving forward/rearward the product. Make sure that both wheels are braked.
• Never place the product close to stairs or steps even if the brake is engaged, as child movements may slide the product.
• Do not leave the chassis fitted with seat unit/carrycot/child car seat on a slope with the baby inside, even if the brake is engaged. Brake efficiency is limited on high gradients.
• Keep your grip on the handlebar when you are near busy roads, railroads or in strong winds as the product may move even if the brake is properly applied.
• Never use the chassis fitted with seat unit/carrycot/child car seat on stairs or escalators with the baby inside, as you may suddenly lose control of the product or the child may fall out. Also take extra care when going up or down a curb or other uneven surfaces.
• Maximum weight for objects placed in basket is 5 kg. The maximum load of the bottle holder is 0,5 kg. Do not use the bottle holder to hold hot drinks. Do not exceed the recommended maximum weight.
• Any load applied to the handle and/or the backrest and/or laterally to the product can compromise the stability of the product.
• Pets attached to the product may affect its stability and cause loose of control.
• Be aware of the risks related to open flames or other heat sources, such as radiators, fireplaces, electric and gas stoves, etc.: do not leave the product close to these heat sources.
• Make sure that all possible sources of hazard (e.g. cables, electric wires, etc.) are kept out of reach of the child.
• Never leave the product with the child inside in places where ropes, curtains or other objects can be used by the child to climb up or cause choking or strangling hazards.
• Never lift the chassis fitted with seat unit/carry cot/child car seat with the child inside.
• WARNING: ENTANGLEMENT HAZARD – Carry handles/ straps of bags shall be left out of the bassinet and outside the occupant area of the seat.
• FALL HAZARD – Prevent children from sitting on the backrest. Seating area is designated by the safety harness.
• Never allow your child to stand or sit in the basket as this may tip the stroller and cause serious injury.

HINTS FOR USE

• Do not use the product if any part is broken, torn or missing.
• Inspect the product and its components regularly for any signs of damage and/or wear, undone stitches and tears. In the event of damage or malfunction, keep the product out of the reach of children, do not use it and/or attempt to repair it, but contact the authorized Retailer immediately for replacement parts or service.
• Do not let other children or pets play unattended near the product or climb on it.
• Assembly, disassembly and adjustments must be carried out only by adults. Make sure that the person using the product (baby-sitter, grandparents, etc.) are aware of its correct operation. This product must only be used by an adult.
• While performing any adjustment, make sure that no moving part of the product (e.g. backrest, hood, etc.) comes into contact with the baby. Always make sure that the brake is completely engaged when performing these operations.
• Do not leave the baby in the chassis fitted with seat unit/carrycot/child car seat when travelling on transport means (eg. train, bus, etc).
• Do not use the stroller seat unit as a car seat.
• Remove the content of the basket before folding the chassis.
• When the product is not used, it must be stored out of reach of children. The product shall not be used as a toy! Do not let the child play with it.
• Do not remove/attach the seat unit when your child is sitting in it and do not transport the baby in the stroller seat separately from the chassis.
• In case of prolonged exposure to sunlight, let the product cool down before using it.
• To avoid overheating and skin burns , do not expose the child to direct sunlight for prolonged period of time, even if the canopy is fully extended.
• For car seats used in conjunction with a chassis, this vehicle does not replace a cot or a bed. Should your child need to sleep, then it should be placed in a suitable pram body, cot or bed.

RAINCOVER

WARNING!

• Use under an adult surveillance.
• When in use make sure the rain cover does not come in contact with the face of the child as it may cause suffocation.
• Never use the rain cover with the product without the hood that keeps the rain cover away from your child’s face. The correct installation of the raincover is with open hood as shown in the instructions.
• Use only on the Inglesina stated product.
• Do not use on products other than those recommended by the Manufacturer.
• To avoid risk of suffocation or overheating never use the rain cover in the sun or in enclosed spaces.
• Hand wash at 30° C.

MANUFACTURER’S CONVENTIONAL WARRANTY

• L’Inglesina Baby S.p.A. guarantees that every article has been designed and manufactured in compliance with the general product quality and safety standards/regulations in force in the European Union and the countries it is marketed in.
• L’Inglesina Baby S.p.A. guarantees that during and after the manufacturing process, every product has undergone various quality controls. L’Inglesina Baby S.p.A. guarantees that, at the time of purchase from the Authorised retailer, every product had no installation or manufacturing defects.
• This warranty does not invalidate the rights acknowledged to the consumer by the applicable national legislation, which may vary depending on the country in which the product was purchased and the provisions of which, in the event of a contrast, prevail over the contents of the warranty herein.
• In the event of material or manufacturing defects detected at the time of purchase or during normal use, as described in the relevant instruction manual, L’Inglesina Baby S.p.A. grants a consecutive 24-month warranty from the date of purchase.
• The warranty is only valid in the country where the product was purchased and if it was purchased from an Authorised Retailer.
• The warranty acknowledged is valid for the first owner of the product purchased.
• The warranty covers the replacement or repair free of charge of parts with factory defects. L’Inglesina Baby S.p.A. reserves the right to decide at its sole discretion whether to apply the warranty via the repair or the replacement of the product.
• To apply the warranty, the product serial number needs to be presented, along with a copy of the receipt issued at the time of purchase of the product, making sure that the date of purchase is indicated in a clearly legible form.
• This warranty will be automatically made null and void in the event that
  • the product is used for purposes that are not expressly indicated in the relevant instruction manual.
  • the product is not used in compliance with the relevant instruction manual.
  • the product has been repaired by unauthorized and unaffiliated Customer Care centers.
  • the structural or textile part of the product has been modified and/or tampered with, without prior expressed authorization by the manufacturer. Any modifications made to the products relieve L’Inglesina Baby S.p.A. from any liability.
  • the defect is due to negligent or careless use (e.g., violent shocks to the structural parts, exposure to aggressive chemical substances, etc.).
  • the product presents normal wear (e.g., wheels, moving parts, fabrics) due to prolonged and continuous use. the product has been damaged, even accidentally, by the owner himself/herself or by third parties (for instance when it has been sent as luggage in air freight or using other means).
  • the product is sent to the retailer for assistance without the original receipt and/or without the serial number or when the date of purchase on the receipt and/or the serial number are not clearly legible.
• Any damage caused by the use of accessories not supplied and/or not approved by L’Inglesina Baby, shall not be covered by the warranty.
• L’Inglesina Baby S.p.A. shall not be held liable for any damage to property or injuries to persons resulting from the improper and/or misuse of the product.
• After the warranty period has expired, the Company guarantees customer care service for consideration for its products for a maximum period of four (4) years from the date said products were placed on the market; after this period, assistance interventions will be assessed case by case.

SPARE PARTS / AFTER SALES SERVICES

• Regularly inspect the safety devices to ensure the product’s functionality over time. Do not use the product in the event of any malfunction and/or anomaly. Promptly contact your Authorised Retailer or the Inglesina Customer Care service.
• Do not use spare parts or accessories not supplied and/or not approved by L’Inglesina Baby S.p.A.

WHAT TO DO IF YOU REQUIRE ASSISTANCE

• If you require assistance for your product, immediately contact the Inglesina Retailer that sold it to you, with the “Serial Number” relative to said object ready on hand.
• It is the Retailer’s duty to contact Inglesina to assess the best suited intervention case by case and then provide the subsequent indications.
• The Inglesina Customer Care Service can provide any information, following written request by filling out the form provided on the website: inglesina.com – Warranty and Assistance section.

HINTS FOR CLEANING AND MAINTAINING THE PRODUCT

• This product requires regular maintenance by the user.
• Never force any mechanisms or moving parts; in case of doubt, check the instruction first.
• Do not store the product if it is still wet and do not leave it in humid environments since mildew may form.
• Store the product in a dry place.
• Protect the product against weather agents, water, rain or snow; moreover, continuous and prolonged exposure to sunlight can cause changes in the colour of many materials.
• Should the product be used on the beach, carefully clean and dry it afterwards in order to remove sand and salt as they may cause rusting.
• Clean the plastic and metal parts with a damp cloth or with a mild detergent; do not use solvents, ammonia or benzine.
• Carefully dry metal parts after any contact with water to prevent the formation of rust.
• Keep all moving parts clean and, if necessary, lubricate them with light oil.

HINTS FOR CLEANING THE TEXTILE LINING

• It is recommended to wash the lining separately from other items.
• Periodically revive the fabric parts using a soft clothes brush.
• Follow the lining washing instructions on the labels.

Handwasher in cold water

Do not bleach

Do not tumble dry

Dry flat in shade

Do not iron

Do not dry clean
Do not spin-dry

• Dry the textile lining completely before using or storing it.
• To prevent formation of mildew, it is advisable to air the carrycot periodically. In particular, separate the textile lining from the structure and run a dry cloth over the bottom.

INSTRUCTIONS

LIST OF COMPONENTS

fig. 1 APTICA CHASSIS

• A Rear wheels
• B Front wheels assembly
• APTICA CARRYCOT
• C Hood lining
• D Carrycot apron
• ALL SEASON STROLLER
• E Stroller seat
• F Comfort Cover
• G Handrail
• J Hood
• ACCESSORIES
• H Feeding bottle holder
• K Storage basket
• L Muff (if available)
• M Rain cover (if available)

CAB 0+ / DARWIN INFANT / DARWIN INFANT RECLINE CAR SEAT (IF AVAILABLE)
STANDUP (IF AVAILABLE)

CHASSIS

CHASSIS OPENING
fig. 2 Holding the lever (T1) down, lift the chassis firmly until it opens completely.
fig. 3 Caution : ensure that all locking mechanisms are properly engaged on both sides before use and that none of the red indicators are visible.

ASSEMBLING/REMOVING THE REAR WHEELS
fig. 4 Insert the rear wheels (A) into the seats on the chassis and push them until they click into place.

fig. 5 Caution : make sure that the wheels are properly attached before use.
Should it be necessary, the rear wheels can easily be removed. fig. 6 To remove the rear wheel (A) act on the lever (A1) and at the same time extract it from its seat on the chassis.

REMOVING/ASSEMBLING THE FRONT WHEEL ASSEMBLY
Should it be necessary, both front wheel assemblies (B) can easily be removed.
fig. 7 Pushing the small button (B1), pull the wheel assembly out from its housing in the support.

fig. 8 To reinstall it, simply position it and push it until it clicks into place.
fig. 9 Caution: make sure that the wheels are properly attached before use.
CLOSING THE CHASSIS
fig. 10 Press the button (T2) and simultaneously rotate the rear handle (T3) until the chassis closes completely.

Caution: always check that the chassis is closed correctly. fig. 11 To transport the closed chassis, use the rear handle (T3).

Never lift the chassis by the handlebar.

REAR WHEELS BRAKE
fig. 12 To operate the brake, press on the centre lever (T4).
fig. 13 To release the brake, lift the centre lever (T4). Always engage the brake during stops.

BLOCKING/UNBLOCKING THE FRONT WHEELS
The chassis features swivel wheels.
fig. 14 To lock or unlock them make sure they are correctly aligned, then operate the lever (B2) located on both front wheel units.

ADJUSTING THE HANDLEBAR
The chassis features a telescopic handlebar, which can be adjusted to 4 different positions.
fig. 15 Operate both buttons (T5) and simultaneously raise or lower the handlebar to the desired position.

STORAGE BASKET
The chassis is equipped with a large storage basket (K), which can be easily removed if necessary.
fig. 16 To remove the basket, undo the 4 snap fasteners (K1) that secure it to the side tubes and detach the Velcro flap (K2) from the rear tube (T6).

fig. 17 Detach the 3 lower snap fasteners and pull the rear flap (K3) off the central brake unit.
fig. 18 Detach both footplate hooks (K4) from their respective pins (T7).
fig. 19 With the aid of a screwdriver or similar tool (not included), expand the front seats (K5) and at the same time pull off the latch straps (K6) on both sides.

To reinstall the basket, carry out the above operations in reverse.

FEEDING BOTTLE HOLDER
The chassis is equipped with a standard feeding bottle holder (H).
fig. 20 To fasten the feeding bottle holder, place the upper guide in correspondence of the hook (H1) on the chassis and push it in its housing until it is fully attached.

ADDITIONAL CARRYING UNITS FOR CHASSIS: CARRYCOT, STROLLER SEAT AND CAR SEAT (if present)
fig. 21 The chassis can be used with the Aptica carrycot, the All Season stroller seat and the Cab 0+ / Darwin Infant / Darwin Infant Recline car seat, if present.

APTICA CARRYCOT

ATTACHING THE CARRYCOT TO THE CHASSIS
fig. 22 Take the carrycot from the handle and attach it to the chassis in correspondence of the housings on both sides of the structure and place it solely facing the parents.

fig. 23 Once the carrycot is installed, check that the indicators (C1) on both the attachment devices are Green. If they are Red, reposition the carrycot correctly until the indicators turn Green.

fig. 24 Caution: before use, make sure that the carrycot is properly attached on both sides by pulling it upwards.
DETACHING THE CARRYCOT FROM THE CHASSIS
fig. 25 Operate the lever (C2) located outside the carrycot and simultaneously lift it, gripping it by the handle.

FITTING THE HOOD LINING

fig. 26 Wrap the hood lining (C) around the handle, fixing it with the dedicated buttons (C3) and with the central Velcro fastening strap (C4).

fig. 27 Complete the fitting by attaching the side and rear Velcro fastenings (C5) to the carrycot.

HANDLE AND HOOD ADJUSTMENT

fig. 28 To adjust both the handle and the carrycot hood, press the two internal buttons simultaneously (C6).
fig. 29 Caution : Before carrying or lifting the carrycot, always check that the handle is in its vertical position and properly locked on both sides.

ATTACHING THE APRON

fig. 30 To fit the apron (D) on the carrycot, first fix the press studs (D2) and then the two slot buttons (D3).

fig. 31 The front flap of the apron (D1) can be extended and fixed in a position that protects your child from the cold.

fig. 32 To facilitate access to the child, the apron can be partially folded, detaching only the two side press studs (D2). The apron stays fixed to the carrycot through the two slot buttons (D3).

BACKREST ADJUSTMENT
fig. 33 Operate the lever (C6) to adjust the backrest : once the desired position is reached, set the lever to the starting position.

CARRYCOT VENTILATION

The Aptica carrycot features a coordinated ventilation system.
fig. 34 The ventilation of the base can be adjusted using the lever (C7) at the front.

fig. 35 If present: The two mesh inserts on the back and on the hood permit greater circulation of air inside the carrycot.

MATTRESS AND INTERNAL LINING MAINTENANCE
It is advisable to remove the mattress and internal lining periodically for correct maintenance.
fig. 36 To remove the internal lining simply release it from the edge of the carrycot.
CARRYCOT LINING MAINTENANCE
fig. 37 If it is necessary to remove the carrycot cover, simply pull it off by unfastening the perimeter straps from the seats on the structure.

fig. 38 When refitting it, ensure that the two elastic loops (C8) are fitted perfectly underneath the lower tabs (C9) on both attachment devices.

Caution! Incorrect positioning of the elastic loops could interfere with correct attachment of the carrycot to the chassis.

ALL SEASON STROLLER SEAT

ATTACHING THE STROLLER SEAT TO THE CHASSIS
fig. 39 Attach the stroller seat (E) to the chassis, positioning it in the dedicated housings on both sides of the structure.

ADJUSTING THE BACKREST
fig. 40 The backrest can be adjusted to 4 positions; use the central device (E1) and bring the backrest to the desired position.

fig. 41 Caution: before use, make sure that the stroller seat is properly attached on both sides by pulling it upwards.

DETACHING THE STROLLER SEAT FROM THE CHASSIS
fig. 42 Operate the lever (E2) and simultaneously lift the stroller seat from the chassis.

Caution: do not, under any circumstance, carry out this operation with the baby inside.
fig. 43 The stroller seat can be used both facing the parent and facing the street.
ADJUSTING THE FOOTREST
fig. 44 To lower the footrest, use both levers (E3) positioned on the lower part and simultaneously press them downwards.

fig. 45 To lift the footrest, simply pull it upwards and it shall automatically lock into position.

SAFETY BELTS
fig. 46 Ensure that the safety belts are inserted in the eyelets at the height of the shoulders or immediately above. If the position is not correct, remove the belts from the first pair of eyelets and reinsert them in the second one. Position both back straps always at the same height.
fig. 47 Fit the ends of the back straps (E4) and of the waist straps (E5) in the central buckle (E6).

fig. 48 Always use the waist strap together with the back harness, adjusting both of them properly.

Caution! Failure to observe this precaution could cause your baby to fall or slip, risking injury.
Caution: adapt the height and the length of the harness according to the baby’s growth.

ATTACHING THE HANDRAIL
fig. 49 To attach the bumper bar (G), fit it in the dedicated housings (G2) in the stroller seat until it clicks into place.

fig. 50 The handrail can be open on one side or fully removed; to open it, press the button (G1) and remove it from its housing; to remove it, repeat the procedure on the other side.

ATTACHING THE STROLLER HOOD
fig. 51 To secure the hood (J), go next to the side joints (J1) on the stroller seat, fit the strap (J2) and push strongly until it clicks completely.
fig. 52 First button the press studs (J3) to the side joints (J1), then all rear buttons (J4) to the backrest.
fig. 53 To adjust the hood, simply accompany it to the desired position.
fig. 54 The hood features an additional fabric insert and sun shade that extend the degree of cover, improving protection from the sun.

DETACHING THE HOOD FROM THE STROLLER
fig. 55 To remove the hood (J) from the stroller seat, remove all the buttons (J4) that secure it to the backrest. fig. 56 Remove the two snap fasteners (J3) that secure the hood to the side joints (J1), then pull the internal strap (J2) from the joints, pulling it firmly from both sides.

HOOD LINING MAINTENANCE
The hood lining can be removed to allow for its correct maintenance.
fig. 57 Once the hood is released from the stroller, simply pull out the internal strap (J2).

CLOSING THE CHASSIS WITH THE STROLLER SEAT ATTACHED (STROLLER CONFIGURATION)
The chassis can be closed with the stroller seat attached, both facing the parent and facing the street.

Facing the parent
fig. 58 Before closing the stroller, fold the hood, recline the backrest to its most horizontal position, and then fully close the stroller, as detailed above.

Facing the street
fig. 59 Before closing the stroller, fold the hood and bring the backrest fully forward, then fully close the stroller as detailed above.

COMFORT COVER
The All Season stroller seat is equipped with Comfort Cover as standard outfit.
The cover, designed to make the child’s walk more comfortable as well as to guarantee extra protection during the colder season, can be easily removed.
fig. 60 To remove it, simply undo the two snap fasteners (E7) that lock the side panels of the upholstery to the chassis, thus releasing the two side anchors (E8).

fig. 61 Remove the back straps from both shoulder straps, then pull them and the lumbar straps out of the slots provided.

fig. 62 Remove the cover (F) from the backrest by pulling the shoulder straps out of their respective slots. Take care to detach it correctly at the rear adjustment device (E1).

STROLLER SEAT LINING MAINTENANCE
It is recommended to remove the lining periodically to provide for its correct maintenance.
To facilitate covering removal, first remove the hood, bumper bar and the Comfort Cover.
fig. 63 Detach the two lower snap fasteners (E9) that secure the cover to the seat.
fig. 64 Unfasten the two side buttons (E7), remove the side panels from their seats, then the cover from the footrest.

fig. 65 Remove the crotch strap from its protective pad, releasing it from the locking elastic, then from the slot on the seat.

fig. 66 Pull the lower back straps out of the slots in the centre of the backrest.
fig. 67 Unbutton the two straps (E10) that secure the cover to the lumbar structure, then pull the two anchoring straps (E11) out of the appropriate slots (E12).

fig. 68 Release the cover from the side hood joints, pull the back straps out of the slots on the cover, then pull it off the back structure.

REMOVAL/INSTALLATION OF THE SAFETY HARNESS SYSTEM
The All Season stroller is equipped with a safety harness system that can be removed if necessary.
fig. 69 To remove the crotch strap, pull the lower ring (E13) out of the slot on the seat (E14).

fig. 70 To remove the lower back strap, push the belts through the slot on the backrest (E15) and pull one portion firmly until the ring (E16) is released from its seats. Then remove the ring (E16) from the slot (E15) and pull the belt out completely.

fig. 71 To remove the back straps, simply pull them off the metal rings (E17) that secure them to the backrest tube.

fig. 72 To install the crotch strap, fit the lower ring (E13) only in the slot on the seat (E14). The lower ring (E18) must remain on the outside.

fig. 73 To reassemble the lower back strap, insert the ring (E16) in the appropriate slot on the backrest and, once it is positioned under one of the hooking tabs (E19), push it firmly into place.

fig. 74 To reattach the back straps, wrap them individually around the backrest tube, making sure they are not inverted or twisted.

fig. 75 Insert each belt into its respective metal ring (E17), taking care that they are positioned outside the backrest adjustment device (E1).

Caution! Position the back harnesses always at the same height.
fig. 76 Caution! Make sure that all the belts are correctly attached to the stroller seat by pulling them individually.

FOOTMUFF (if available)fig. 77 Position the footmuff (L), passing it under the bumper bar, and attach the press studs (L1).

fig. 78 The flap of the footmuff can be extended and attached in a position suitable for protecting the child from the cold, fastening it with the external side press studs to the corresponding elements (L2) on the canopy.

fig. 79 The footmuff can be used both facing the parent and facing the street.

RAIN COVER (if available)
fig. 80 To fit the rain cover (M), position it on the hood and button both press studs (M1) on the sides of the stroller seat.

fig. 81 Then hook the bands (M2) around the front tubes, at the wheel assembly.

INFANT CAR SEAT CAB 0+ / DARWIN INFANT / DARWIN INFANT RECLINE (if

available)

ATTACHING THE INFANT CAR SEAT TO THE CHASSIS
fig. 82 Take the infant car seat from the handle and attach it to the chassis in correspondence of the housings on both sides of the structure and place it solely facing the parents.

fig. 83 Caution: before use, make sure that the car seat is properly attached on both sides by pulling it upwards.

DETACHING THE INFANT CAR SEAT FROM THE CHASSIS
fig. 84 Operate the lever (S1) on the back of the seat and simultaneously lift it from the chassis, gripping it with the handle.

To use the infant car seat properly, refer to the dedicated manual.

References

• Inglesina | There is a Story Inside

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>