CANOPIA Arizona Breeze 5000 Aluminium Doppelcarport Instruction Manual
- June 13, 2024
- CANOPIA
Table of Contents
ARIZONA™ BREEZE
10×16 / 3×5
HOW TO ASSEMBLE
www.canopia.com
Arizona Breeze 5000 Aluminium Doppelcarport
IMPORTANT!
Please read these instructions carefully before starting assembly.
Keep these instructions in a safe place for future reference.
AVAILABLE MODELS
TOOLS & EQUIPMENT
HAVE A CONCERN ?
WE CAN HELP.
Before returning your purchase:
You didn’t find what you
were looking for?
We can help at
canopia.shop/support
Still can’t find what you are looking for?
Please see next page for local customer care.
WE ARE HERE TO HELP
For general questions: canopia.com/contact-us
NORWAY • SWEDEN • ARGENTINA • GREECE • GREENLAND • ICELAND • ESTONIA • JAPAN •
LATVIA • LITHUANIA MAURITIUS • MEXICO • ROMANIA • RUSSIA • TURKEY • UZBEKISTAN
• UKRAINE • SWAZILAND • KOREA
+972-4-848-6816
customer.service@palram.com
| USA | CANADA | HUNGARY • SLOVAKIA |
|---|
877-627-8476
generalsupport@poly-tex.com|
905-5646007
sales@footprintproducts.com|
+420-493-523-523
servis@garland.cz
UNITED KINGDOM • IRELAND| GERMANY| NEW ZEALAND
01302-380775
customer.serviceUK@palram.com|
0180-522-8778
customer.serviceDE@palram.com| 0800
800 880
customer.service@palram.com
FRANCE • BELGIUM| ISRAEL| DENMARK
+33-169-791-094
customer.serviceFR@palram.com|
04-848-6800
customer.service@palram.com| 07-575 42
70
post@nshnordic.com
ITALY • NETHERLANDS • PORTUGAL • SPAIN| AUSTRIA • LUXEMBURG • LIECHTENSTEIN|
SOUTH AFRICA
+33-169-791-094
customer.serviceFR@palram.com|
+49-180-522-8778
customer.serviceDE@palram.com|
011-397-7771
receptionza@palram.com
AUSTRALIA| AUSTRALIA – GREENHOUSES| CROATIA • SLOVENIA
03-9219-4444
salesvic@palram.com| 03-9544-6-999
info@mazedistribution.com.au|
0599-37-057
info@ms-viscom.com
CZECH REPUBLIC| SWITZERLAND| POLAND
0493-523-523
servis@garland.cz| 062-287-33-77
info@ritter.ch| Infolinia: 801-011-929
22-349-93-36
kontakt@ogrodosfera.pl
CYPRUS| FINLAND|
0224-971-13
alpaco@alpacodomica.com
www.alpacodomica.com| Neuvonta: 09-6866720 Tuki
/ Varaosat: 050-3715350
www.horisontenterprises.fi
tuki@horisontenterprises.fi|
SITE PREPARATION & FOUNDATION
A – PREPARE THE SITE
The product must be positioned and fixed on a flat level surface.
-
– Clear the site
-
– Level the ground
B – FOUNDATION
In order to assemble this product, it is essentialto first dig 2 holes
(pits) according to the instructions (for all surfaces).
Use wooden beams (not supplied) to assist in leveling of the aluminum poles.
Pour the concrete casting into the holes and and wait till dries before
contiuing assembly.
More details are available in Steps 1-7.
DIMENSIONS
The Illustration describes center-to-center distance between poles.
Required for assembly (in addition to the previously depicted tools).
- 8 wooden beams, minimum 6′ long (1.8 m)
- Concrete
- Digging equipment, compatible with the soil type and required measurements
INFORMATION
SAFETY ADVICE
- It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
- Always wear work gloves during panel sliding.
- Always wear shoes and safety goggles when working with extruded aluminium.
- If using a step ladder or power tools make sure that you follow the manufacturer’s safety advice.
- Do not touch overhead power cables with the aluminium profiles.
- Do not climb or stand on the roof . Keep children away from the assembly area.
- Do not attempt to assemble the product in windy or wet conditions.
- Dispose of all plastic bags. Keep them out of reach of small children.
- Do not lean against or push the products during construction.
- Do not position your product in an area exposed to excessive winds.
- Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
- Make sure there are no hidden pipes or cables in the ground before anchoring to foundation.
- This product is designed to be used mainly as a carport.
- Heavy snow load on the roof can make it unsafe to stand below or nearby . Keep roof and gutters clear of snow, dirt & leaves.
- Make sure to anchor the product directly to a solid foundation to increase the product’s stability and wind resistance, especially in areas with severe weather conditions.
CARE & MAINTENCE
- When your product needs to be deaned, use a soft cloth and rinse with cold clean water.
- DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
- Clean the product once assembly is complete.
BEFORE ASSEMBLY
-
Selecting a site:
– Choose your site carefully before beginning assembly.
– Choose a sunny position away from overhanging trees.
– The product must be positioned and fixed on a flat level surface. -
The product must be secured directly to a solid foundation.
-
Take all components & parts out of the packages. Sort the parts and check against the content parts list.
-
Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost .
-
Please note multi-sided profiles are used in this product. As a result some holes in the profiles are not used during assembly.
-
Please review entire instructions before starting. Carry out the assembly steps in exact order.
-
Please consult your local authorities if any permits are required prior to constructing the product.
-
Use only the parts registered in the content list, some parts may be surplus.
IMPORTANT!
- Firmly connect the product to a level surface immediately after completion of the assembly.
- Anchoring this product to the ground is essential to its stability and rigidity. It is required to complete this stage in order for your warranty to be valid.
- During assembly use a soft surface below the parts to avoid scratches and damages.
- We recommend checking for restrictions or covenants for building this product in your area. In addition we advise to check if you need to submit any forms or if any permit is required prior to building the prcduct.
DURING ASSEMBLY
During assembly, you will encounter different icons for different products. Please see below for more information:
| You may use silicone lubricant spray on the frame in order to help you slide
the panels into the profiles. Do not spray the panels.
---|---
| Use a rubber mallet if necessary.
| All panels with the stamped words “THIS SIDE OUT” must be facing out to
create full UV protection. Remove plastic sticker as panels are locked in
place.
| Steps marked with dashed outlines refer to Extensions only. Some of the
steps are irrelevant for an assembly of a single product. When assembling a
single or an extended product, some parts may be surplus.
| These 2 icons below indicate if screw’s tightening is required or not.
Temporary tightening of a few screws may be needed to prevent a profile from
sliding out. Tighten all screws once assembly is completed.
IMPORTANT ASSEMBLY STEPS
When encountering this information icon during assembly, please refer the relevant assembly step for important additional comments.
Step 1 : Dig two (2) holes according to the specified measurements and make sure the bottom is tight/well packed. Plan ahead according to the placement of the parking as shown in the drawing. Make sure the pits’ walls are at a 90°. If the ground is sandy and digging proper holes is impossible, please consult a local expert / constructor.
Step 2 : Profiles #8646 come covered in plastic film, please do not peel at this point, it serves to protect the profiles from the concrete. These profiles assist in stabilizing the concrete casting, and will be later assembled in the roof.
Step 5 :
Please use wooden beams (not supplied) to set and hold the aluminum poles in
place, make sure the profiles are set at a depth of 19.6″ (50 cm) in
accordance with the former Step (4). The aluminum poles must be leveled in all
directions. Step 6: Please ensure the concrete casting reaches the line that
was marked on the profile at the previous steps.
Step 7 : Please wait for the concrete to be fully set and dry, in accordance with the manufacturer’s instructions and depending on the weather conditions, before continuing with the assembly! Step 9: Please note the profile’s direction.
Step 19 : Optional: if you find it difficult to tighten the screws, it is possible to use toggle clamps before tightening the screws. Make sure the toggle clamps do not come in direct contact with the powder coated profiles! Use a wooden plank in order to protect the profile from bending. Step 30: In order to be able to tighten the screws, use a high step ladder. Be careful!
Contents
10 YEAR LIMITED WARRANTY
PALRAM – CANOPIA 1 10 YEAR LIMITED WARRANTY
Palram Canopia Ltd. (Company number: 512106824) whose registered office is at
Teradion Industrial Park M.P Misgav 2017400, Israel (“Canopia”) warrants that
the product will be free from defects in material or workmanship for a period
of 10 years from the original date of purchase.
- This warranty is valid only if the product is installed, handled, cleaned, and maintained in accordance with Canopia’s written specifications.
- This warranty does not cover defects resulting from normal wear and tear including, but not limited to: damage caused by use of force, incorrect handling, inappropriate use, negligence, accidents, impact from foreign objects, vandalism, pollutants, alteration, painting, damage resulting from cleaning with incompatible detergents or minor deviations of the product.
- This warranty does not apply to damage resulting from “acts of Nature”, which includes but is not limited to hail, storm, tornado, hurricane, blizzard, flood, or fire.
- Upon submitting proof of purchase and evidence of the claimed product failure, and subject to reporting the failure in writing within 30 days after discovery of the defect, Canopia, at its sole discretion, will replace defective parts of the Product, or refund you a prorated portion of the purchase price on a straight-line depreciated basis for the length of the warranty.
References
- Contact Us Archive - Canopia
- Support Archive - Canopia
- tex.com
- Inspection Systems for the Electronics Industry – Viscom – Viscom
- Αρχική Σελίδα - Alpaco Domica
- Canopia United Kingdom - Celebrate Outdoor Living
- Contact Us Archive - Canopia UK
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>