SEALEY SV12 Series CP1205 Cordless Polisher Instructions
- June 13, 2024
- SEALEY
Table of Contents
12V SV12 SERIES Ø71MM CORDLESS POLISHER
– BODY ONLY
MODEL NO: CP1205
SV12 Series CP1205 Cordless Polisher
Thank you for purchasing a Sealy product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
1.1. GENERAL SAFETY
Disconnect the polisher from the battery unit before changing accessories,
servicing or performing any maintenance.
Maintain the polisher and battery in good condition. Check moving parts
alignment on a regular basis.
Replace or repair damaged parts. Use an authorised service agent and
recommended parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
Ensure the polisher is switched off before installing the battery pack.
Keep the polisher and charger clean for best and safest performance.
Remove ill fitting clothing. Remove ties, watches, rings and other loose
jewellery and contain long hair.
Evaluate your working area before using the polisher e.g. ceilings, floors and
enclosures may contain electrical items or water piping.
Ensure battery pack is correctly inserted into the polisher handle and latched
in place before attempting to switch on polisher.
Secure loose work pieces with a clamp, vice or other adequate holding device.
Avoid unintentional starting.
Wear approved safety eye protection (standard spectacles are not adequate).
Maintain correct balance and footing. Ensure the floor is not slippery and
wear non-skid shoes.
Keep children and unauthorised persons away from the working area.
Store polisher and charger in a safe, dry, childproof area where the
temperature will not exceed 104°F (40°C).
DO NOT use the polisher where there are flammable liquids, solids or gases,
such as paint solvents, etc.
DO NOT allow children to operate the polisher.
DO NOT operate the polisher if any parts are missing as this may cause failure
and/or personal injury.
DO NOT hold unsecured work piece in your hand.
DO NOT leave the polisher operating unattended.
DO NOT carry the polisher with your finger on the power switch.
DO NOT use the polisher for a task it is not designed to perform.
DO NOT operate the polisher when you are tired or under the influence of
alcohol, drugs or intoxicating medication.
DO NOT get the polisher or battery wet or use in damp or wet locations.
1.2. HAND ARM VIBRATION
WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed
adequately.
This tool is subject to the vibration testing section of the Machinery
Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 4.213m/s²
Uncertainty value (k): 1.5 m/s²
Please note that the application of the tool to a sole specialist task may
produce a different average vibration emission. We recommend that a specific
evaluation of the vibration emission is conducted prior to commencing with a
specialist task.
A health and safety assessment by the user or employer will need to be carried
out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to
be typical.
Whilst in use, the actual value will vary considerably from and depend on many
factors, such as the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted
use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a
poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
1.3. HEALTH SURVEILLANCE
We recommend a programme of health surveillance to detect early symptoms of
vibration injury so that management procedures can be modified accordingly.
1.4. PERSONAL PROTECTIVE EQUIPMENT
We are not aware of any personal protective equipment (PPE) that provides
protection against vibration injury that may result from the uncontrolled use
of this tool. We recommend a sufficient supply of clothing (including gloves)
to enable the operator to remain warm and dry and maintain good blood
circulation in fingers etc. Please note that the most effective protection is
prevention, please refer to the Correct Use and Maintenance section in these
instructions. Guidance relating to the management of hand arm vibration can be
found on the HSC website www.hse.gov.uk – Hand-Arm
Vibration at Work.
INTRODUCTION
Compact, lightweight cordless polisher. Comfortable composite housing with soft grip to reduce vibration. 2-Speed settings and variable speed control trigger make this polisher easy-to-use. Integral LED battery level indicator. Supplied with side handle, two foam pads and one wool polishing pad. Requires Model No. CP1200BP 12V 1.5Ah Lithium-ion Battery and Model No. CP1200MC Battery Charger.
SPECIFICATION
Model No: …………………………………………………. CP1205
Battery Options (not included): ….. 12V 1.5Ah Lithium-ion
……………………………………………….. 12V 3Ah Lithium-ion
……………………………………………….. 12V 4Ah Lithium-ion
Noise Power/Pressure: …………………………… 90/79db(A)
No-Load Speed: ………………………0-2500rpm/0-7500rpm
Pad Size: ………………………………………………….. Ø71mm
Replacement Parts:………… CP1200MC – Mains Charger
Thread Size:……………………………………………..5/16”UNF
Vibration/Uncertainty: ………………………….. 4.213/1.5m/s²
OPERATION
WARNING! Before use, ensure that you have read and understood Section 1
Safety Instructions.
4.1. USING THE POLISHER
4.1.1. To attach/remove the applicator pad depress the chuck lock button
behind the chuck (fig.1) and screw/unscrew the applicator pad.
4.1.2. Release the chuck lock button and check that applicator pad is locked
into chuck before switching on.
4.1.3. Attach the battery to the sander. The battery charge level indicator
LEDs (fig.1) show charge (three green lights indicate full charge).
4.1.4. Set the required speed by use of the speed selector switch (fig.1).
4.1.5. Unlock the drive mechanism by use of the slide switch (fig.1).
4.1.6. Grip the side handle (not shown) and start the polisher by gentle and
slow application of pressure on the trigger (fig.1).
4.1.7. Increase/decrease the speed of the polisher using the variable speed
control trigger (fig.1) to suit the task.
4.1.8. Ensure that the above features are working correctly prior to use.
MAINTENANCE
WARNING: Always disconnect the battery before carrying out any
inspection, maintenance or cleaning.
5.1. GENERAL
5.1.1. Regularly check that all the fixing screws are tight.
5.1.2. Repairs should only be carried out by an authorised service centre.
5.2. CLEANING
WARNING: Always wear protective equipment including eye protection and
gloves when cleaning this tool.
5.2.1. Keep your tool clean at all times. Dirt and dust will cause internal
parts to wear quickly, and shorten the device’s service life.
5.2.2. Clean the body of your machine with a soft brush, or dry cloth.
5.2.3. Never use caustic agents to clean plastic parts. If dry cleaning is not
sufficient, a mild detergent on a mildly damp cloth is recommended.
5.2.4. Water must never come into contact with the tool. Ensure the tool is
thoroughly dry before using it.
5.2.5. If available, use clean, dry, compressed air to blow through the
ventilation holes (where applicable).
WEEE REGULATIONS
** Dispose of this product at the end of its working life in compliance
with the EU Directive on Waste Electrical and Electronic Equipment (WEEE).
When the product is no longer required, it must be disposed of in an
environmentally protective way. Contact
your local solid waste authority for recycling information.
ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
https://qrco.de/bcy2E9
REGISTER YOUR PURCHASE HERE
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealy Group, Kimpson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealy Limited
Original Language Version
CP1205 Issue 3 (ALL) 13/06/23
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>