arte confort OLIVER-S-v3 Ceiling Fan with Light DC Motor Instruction Manual

Instruction Manual
OLIVER S

OLIVER-S-v3 Ceiling Fan with Light DC Motor

WARNING
Reod this instruction manual corefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person.
While using electrical appliances, basic safety Precautions should always be followed to reduce the risk of fire, electric shock and personal injury.
CAUTION

• The product must only be installed by on authorized electrician and in compliance with local, regional and state electricity regulations.

• Check if the electrical specifications of this device are compatible with your installation.

• Turn off the power before installing or repairing the fan.

• The fon must be properly grounded to avoid the risk of electric shock.

• Use and unauthorized technical modifications could suppose a risk of injury.

• The fan must be connected to a 230V 50Hz power supply.

• Do not connect the fon motor to o current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.

• Be careful while working near the spinning blades.

• Never connect the fon to o power point but to the ceiling itself.

• The fon must be installed so that the blades are at least 2,3 meters above the ground.

• The fan must be hung from a structure capable of supporting a weight of at least 50 kg. The fixture must be able to support the weight of the fon in motion and should not wobble or loosen.

• Make sure that the blades do not come in contact with any object at the installation site. Always leave a minimum clearance of 50cm from the tip of the blades to the wall or ceiling. Keep in mind that the larger this space, the better the fani air flow will be.

• This device is designed for indoor use only. Do not use in on open space or where it moy be exposed to water or moisture.

• Never install the appliance in a room with o high degree of humidity.

• The fon must not be started in a room with o
  gas appliance running at the same time.

• This device can be used by children aged 8 years and above and of people with reduced physical, sensory or mental abilities or lock of experience and knowledge if they are supervised or instructed about the use of the device safely and understand the risks involved. As well as cleaning and maintenance of the device

• Children should not ploy with the device.

• To reverse the direction of the blades, do it while moving.

• Do not insert any object into the fan blades while they are rotating. This can damage them and alter the balance of the fon and the device con fall down.

• After the fan is fully installed make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine.
  The instructions and safety regulations in this monuol cannot prevent all conditions and situations that may occur. For obvious reasons, this monuol cannot include factors such os caution and core. These factors must be assumed by who installs, maintains, uses and enjoys the product.

BEFORE INSTALLATION

Open the box avoiding the use of blades or ‘cutters’ to ovoid scratching the fon components.
Unpack the ports handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways.
It Is advisable to mount the fon on the floor or o surface large enough so that no component falls.
Identify all ports before beginning assembly.

TOOLS NEEDED

‘Not included. It is recommended that the screwdriver be magnetized.

MAINTENANCE

• Over time and due to the natural movement of the fon, some connections may come loose. Check the support connections, brackets and attach the blades twice a year, and make sure they ore firm.
• Clean the appliance regularly to maintain its appearance os new. To do this, use a soft, lint-free cloth to ovoid scratching the finish. Never use water, because it could damage the motor or the wood of the blades.
• It is not necessary to grease the fon, since the motor bearings permanently contain lubricant.

WARRANTY

You can check the warranty for this product on its corresponding page at the end of this manual.

ENVIRONMENT

Do not throw electrical appliances into the household waste, use selective collection facilities. Consult loco! authorities for more information.
If electrical appliances ore deposited in landfills, hazardous components can seep into groundwater and enter the food chain, damaging health and wellbeing.
Thanks For taking core of the environment.
This product contains a light source of energy efficiency class E – (EU) 2019/2015

PROBLEM SOLVING

Before corrying out the checks detailed below, the fan must be without power supply.

1. The fan does not start
   • Replace the remote control batteries if they ore exhausted or not suitable.
   • Check that there ore no nearby devices that may be causing interference with the remote or reducing signal reception.
   • Resynchronize the remote control.
   • Check that the electrical connections ore correct (must be carried out by o licensed electrician).
   • Check fuses and switches, that the installation has voltage and it reaches the fan.

2. The fan doesn’t start but the light does.
   • With the fan off, check with your hand that the blades turn freely.

3. The fan makes excessive noise while rotating
   • Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
   • Cheek that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
   • If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.

4. The fan wobbles
   • Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
   • Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.

5. The fan does not give air or the air flow is Insufficient
   • Check that the blades are not mounted backwards.
   • Check that the blades rotate in the correct direction (Summer / Winter).
   • Avoid nearby objects that may impede air circulation.
   • Verify that the diameter of the blades of your fon Is sufficient for the area of the room In which it is installed.

6. The light does not turn on
   • Check the bulb Is not blown, otherwise replaces it with a new one.
   • If your fon has LED light included, check the connections ore properly fixed according to the instruction manual.

COLOR TEMPERATURE MEMORY

The fan has color temperature memory of the light. This function allows you to maintain the some color temperature when the fan light is turned on again.
To change the color temperature of the light press. the button indicated with the color of each color temperature. When you turn the light off and turn it on again it will keep the selected temperature.

REMOTE CONTROL

WINTER/SUMMER MODE
Reverse the dnecnon of rotation of the blades to change to summer mode or winter mode.
ON/OFF LIGHT / SYNCHRONIZATION
Turns the light and synchronization on or off (see section ‘Control synchronizotion’).
ON/OFF FAN
Turn the fon on or off.
SPEED REGULATOR
Increases or decreases the turning intensify of the blades.
LIGHT INTENSITY REGULATOR
Increase Of decrease the Intensity of the light.
LCD INDICATOR
Indicates the number of speeds, from the bottom of the screen to the top.
LIGHT TEMPERATURE
Change the color temperature of the light.
PROGRAMMING
Sets the hours of fan operation (1, 2 or 4 hours).
BREEZE MODE
Activate the breeze mode that alternates smoothly between soft and Post speeds (from speed Ito 3) to create o greater sensation of comfort.
To activate the breeze mode, activate the fon using the *ON/OFF• button on the fon and then press the ‘Breeze mode’ button.
For cancel breeze mode press the ‘Breeze mode’ button again, the fan will return to the rotation speed selected before the breeze mode. You con also press the ‘ON/OFF’ button of the fon to completely slop the rotation of the blades, when you turn it on again it will not remember the breeze mode, activating at the previously selected rotation speed.
The ’emote control IS synchronized from the factory, you only need to re- synchronize it if the synchronization has been lost, if you purchased o new one or wont ro control several Ions with a single remote.

BATTERIES
The remote control batteries ore not included. The required battery model is 2x AAA.
‘Remove the batteries from the controller if it is not going to be used for o long time.

REMOTE CONTROL SYNCHRONIZATION

The remote is factory synchronized, you only n ed to resynchronize the remote if you hove lost synchronization, purchased a new one, want to control several Ions with a single remote, or the fon does not respond to the remote control orders while it is tanning.
A REMOTE CONTROL TO A NEW FAN

1. Cut the current Be sure to cut off the current until the fon stop and wait 30′
2. Restore the current Post 30′ reestablish the current.
3.  Synchronize the remote control Within 10 seconds, press the synchronization button ‘ON/OFF light ( during 3 seconds until you hear the signal and the light flashes. Control range: 8.10m.

A REMOTE CONTROL TO VARIOUS FANS

1. Cut the current Be sure to cut off the current until all fans stop and wait 30.
2. Restore the current Past 30′ reestablish the current.
3. Synchronize the remote control Within 10 seconds. press the synchronization button ‘ON/OFF light ( )’ on each fon during 3 seconds until you hear the signal and the light flashes. If they are within o radius of less than 10m (control range: 8.10m). all will synchronize of the some lime.

A REMOTE CONTROL TO A FAN
(Example for two fans, applicable to o larger number of fans)

1. Cost the fan A current’ Be sure to cut the fan A current (the one we wont to remove the gunchrnniyntinnl and writ 30

2. Cut the Fan B current’ Be sure to cut off fon B (the one we wont to synchronize) and wort 30′.

3. Restore fan B current When you testate the Ion B and within 10 seconds, Press the synchronization button ‘ON/OFF light during 3 seconds until you heor the signal and the light Rashes to synchronize (emote control B with fon B. 

4. Cut the fan B current’ Be sure to cut the fon B current and wait 30″.

5. Restore the fan A current When you restore the fan A and within 10 seconds. press the synchronization button “ON/OFF light air during 3 seconds until you hear the signal and the light flashes to synchronize remote control A with fon A.

6. Repeat the steps Repent steps with each fon you have and wont to individualize its remote control.
   To cut the current you can press the individual fon switch. If there is not, disconnect the quick connect cables from the fon.

OLIVER
SYNCHRONISATION OF TWO REMOTE CONTROLS TO A FAN

TWO REMOTE CONTROLS TO ONE FAN

1. Cut the current Be sure to cut off the current until the fon stop and wait 30
2. Restore the current Post 30′ re-establish the current.
3. Synchronize the remote control A Within 10 seconds, press the synchronization button “ON/OFF light op,y during 3 seconds until you hear the signal and the light flashes. Control range: 8-10m.
4. Cut the current Be sure to cut off the current until the fon stop and wait 30″.
5. Restore the current Post 30′ re-establish the current.
6. Synchronize the remote control B Within 10 seconds, press the synchronization button “ON/OFF light (s)” during 3 seconds until you hear the signal and the light flashes. Control range: 8-10m.

It is not possible to synchronise more then tow controllers to one fan.

GENERAL GUIDE: PARTS OF A FAN

SCREW GUIDE

SCREWS FOR THE ROOF

| Screws for the roof
---|---
| Ceiling screw plugs
| Washer for ceiling screw

SCREWS FOR BLADES

| Screw for wood blades
---|---
| Screw for blades with washer
| Screw for blades
| Paper washer for blade screw

SPARE PARTS
You can request spare parts by going to the store where you purchased it or to any another  of the brand. If the product isunder warranty, present the purchase receipt or invoice.

| DESCRIPTION| REFERENCE
---|---|---
| Light cover| PLABEIRUTS
| LED module| LEDBEIRUTS
| Remote control| MANBEIRUTONLY
| Driver| CONBEIRUTSONLY

WARRANTY

The motor of this fan is guaranteed for 8 years and 3 yeors for the rest of the components. This warranty covers the exchange or repair of any failure or defect of the device, provided that it is due to a manufacturing fault or a defective component.
IMPORTANT
It is essential for the use of this guarantee to prove the purchase date of the product. Therefore, it will be necessary to present the purchase receipt as well os this instruction manual.
**** Keep the purchase receipt and the instruction manual.
The warranty of this product does not apply if the defects of the device have been caused by:

• Damage during transport not carried out by the manufacturer, {Example: dents, components or glass pieces damages …)
• Carrying out incorrect installations or assemblies.
• Poor preservation of the product.
• Damage caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
• The replacement or use of additional parts or accessories that are not original from the manufacturer.
• When using a control through a wall dimmer other than the remote control supplied with the  fon.
  Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual.

If you have any questions, problems or missing components, consult your dealer.
You can also contact us through the email info@arteconfort.com or through the contact form available on our website.

www.arteconfort.com
ARTECONFORT HOTEL S.L.
Ctra. Andalucia, 6
45224 Sesefia Nuevo
Toledo, Espafia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>