Xiaomi T2201 Electric Scooter 4 User Manual
- June 13, 2024
- Xiaomi
Table of Contents
Xiaomi T2201 Electric Scooter 4
Product Information
- Product Name: Electric Scooter 4
- Manufacturer: Xiaomi
- Model: T2201 PVT
- Date: 2022-02-18
- Weight: 80g
- Color: Pantone Cool Gray 11
- Dimensions: 140mm x 140mm
Product Usage Instructions
Safety Precautions
- Avoid hitting your head on door frames, elevators, and other overhead obstacles.
- Do not press the accelerator when you are walking alongside the scooter.
- Unless otherwise authorized by the local laws, it is forbidden and illegal to ride on public roads, motorways, and expressways.
- Do not abruptly change the steering direction at high speed.
Handlebar
- Do not hang bags or other heavy stuff on the handlebar.
Riding on Slopes
- Do not accelerate when going downhill, and brake in time to slow down. When on a steep slope, you need to step off the scooter and push.
Mobile Phone and Earphones
- Do not use a mobile phone or wear earphones when operating the scooter.
Riding in Wet Conditions
- Do not ride in the rain. Do not ride through puddles or any other water obstacles.
Riding with Others
- Do not ride with anyone else, including children.
Stairs and Obstacles
- Do not try riding up or down stairs, nor try jumping over obstacles.
Mudguard and Handlebar
- Do not keep your feet on the rear mudguard.
- Do not let go of the handlebar while riding.
Control Panel & Power Button
- The control panel displays the current speed and any error codes when the scooter is working. It also displays the current battery level when the scooter is charging.
- Press the power button to turn the scooter on/off.
- To turn on/off the headlight and tail light, press the power button when the scooter is on.
- To cycle through the modes, press the power button twice when The scooter is on.
- Note: The scooter will turn off automatically when it enters standby mode for more than 10 minutes. Standby mode means that the scooter is not being charged or not locked when it is on and not running.
Read this manual carefully before use, and retain it for future reference.
Safety Reminder
Always steer clear of obstacles.
Watch out for Safety Risk
- Avoid hitting your head on door frames, elevators, and other overhead obstacles.
- Do not press the accelerator when you are walking alongside the scooter.
- Unless otherwise authorized by the local laws, it is forbidden and illegal to ride on public roads, motorways, and expressways.
- Do not abruptly change the steering direction at high speed.
Do not Try Dangerous Actions
- Do not hang bags or other heavy stuff on the handlebar.
- Do not ride on one foot.
- Do not accelerate when going downhill, and brake in time to slow down. When on a steep slope, you need to step off the scooter and push.
- Do not use a mobile phone or wear earphones when operating the scooter.
- Do not ride in the rain. Do not ride through puddles or any other (water) obstacles.
- Do not ride with anyone else, including children
- Do not try riding up or down stairs, nor try jumping over obstacles.
- Do not touch the disc brake.
- Do not keep your feet on the rear mudguard.
- Do not let go of the handlebar while riding.
Product Overview
- Handlebar
- Buckle
- Headlight
- Brake Lever
- Stem
- Quick Release Lever
- Quick Release Lever Lock
- Front Reflector
- Front Fork
- Wheel Motor
- Charging Port
- Accelerator
- Control Panel & Power Button
- Scooter Bell
- Bell Lever
- Deck
- Hook
- Rear Mudguard
- Kickstand
- Battery Compartment
- Disc Brake
- Side Reflector
- Tail Light & Rear Reflector
Control Panel & Power Button
- Speedometer: It displays the current speed when the scooter is working. When the scooter has an issue, it displays an error code. When the scooter is charging, it displays the current battery level.
- Bluetooth: When the icon lights up, it indicates the scooter has been successfully connected to the mobile device.
- Temperature Warning: If the battery temperature is too high or too low, the thermometer icon will be on. This will result in reduced acceleration and possibly charging issues. Use or charge the scooter after its battery temperature returns to the normal operating range.
- Error Notification: When the wrench icon displays red, it indicates that the scooter has an error.
- Power Button: Press the button to turn the scooter on, and hold the button for 2 to 3 seconds to turn the scooter off. When the scooter is on, press the button to turn on/off the headlight and tail light, and press twice to cycle through the modes. Note: The scooter will turn off automatically when it enters standby mode for more than 10 minutes. The standby mode means that the scooter is not being charged or not locked when it is on and not running.
- Battery Level: The battery power is indicated by 5 bars, each representing approximately 20% of a full battery.
- Inflation: When the inflation icon is on, it means that it is time to maintain the tires. Check the tire pressure and inflate the tires immediately to avoid tire damage caused by inadequate tire pressure. The recommended tire pressure is 45–50 psi. Note: After performing maintenance, follow the instructions in the app to disable the inflation reminder.
- Lock: When the icon lights up, it indicates that the scooter is locked. You can lock/unlock the scooter via the Mi Home/Xiaomi Home app.
- Cruise Control: The cruise control function is disabled by default and can be enabled in the Mi Home/Xiaomi Home app. To start the cruise control mode, enable the cruise control function in the app first, then ride the scooter stably and hold the accelerator at the same position until the scooter makes a beep. Release the accelerator, and the scooter will keep in cruise control mode. To exit the mode, simply press the brake lever or the accelerator.
Package Contents
- Electric Scooter
- Xiaomi Electric Scooter 4 User Manual
- Xiaomi Electric Scooter 4 Important Information
- Xiaomi Electric Scooter 4 Specifications
- Extension Nozzle (Connect the pump to the valve for easy pumping)
- Extension Nozzle
- Screw × 5 (1 is spare)
- Battery Charger
- Combination Lock
Assembly and Set-up
- Put down the kickstand, and hold up the stem until it is completely in an upright position. Then lift the quick-release lever lock, and push the quick-release lever inward to the end.
- Install the handlebar onto the stem, and make sure to install the handlebar in the correct direction.
- Follow the number order as illustrated to pre-tighten the four screws with the included Allen key. Make sure the handlebar is correctly installed and then tighten the screws thoroughly.
- Once the scooter is assembled, check if it can be turned on/off properly.
- Press the power button to turn the scooter on, and then press and hold the power button for 2 to 3 seconds to turn it off.
Charge Your Scooter
- Lift up the rubber flap.
- Connect the battery charger to the charging port.
- The scooter is fully charged when the LED on the battery charger changes from red to green.
Connect with the Mi Home/Xiaomi Home App
- Before being activated, the scooter will keep beeping when turned on and is limited to 10 km/h.
- When the scooter is used for the first time, it must be activated via the Mi Home/Xiaomi Home app.
- Before being activated, the scooter will keep beeping when turned on and is limited to 10 km/h. When the scooter is used for the first time, it must be activated via the Mi Home/Xiaomi Home app.
- Note: The QR code is unique to your scooter, please keep it safe.
- ap “+” on the top right corner and open “Scan” to scan the QR code on the label attached to the control panel, on the right side of the deck, or on the back cover of the user manual again. Then follow the instructions in the app to add the scooter.
- Watch the riding guide video. Do not exit the video before finishing it. Otherwise, the activation will fail.
- Tap “Activate” to activate the scooter. Once the scooter is activated, the beeping will stop and the speed restriction will be lifted.
Notes
- The app is referred to as Xiaomi Home app in Europe (except for Russia). The name of the app displayed on your device should be taken as the default.
- The version of the app might have been updated, please follow the instructions based on the current app version.
Reset Bluetooth
- Make sure the scooter is turned on. Press the accelerator and simultaneously press the power button 5 times to reset. When the scooter beeps, it has been reset successfully.
Restore Factory Settings
Make sure the scooter is turned on. Squeeze the brake lever, and
simultaneously press and hold the accelerator and the power button for 7
seconds. When you hear a beep, the scooter has been restored to factory
settings. This operation will completely delete the data stored in the
scooter, please proceed with caution.
Note: The scooter cannot be restored to factory settings during riding or
when locked
How to Ride
-
Warning: ear a helmet, elbow pads, and knee pads before riding.
Note : Check the tire pressure before riding. The recommended tire pressure is 45–50 psi. -
Step on the deck with one foot, and slowly kicks off the other on the ground.
-
When the scooter starts to coast, put both feet on the deck and gently press the accelerator. The accelerator can be used once the scooter is going over 5 km/h.
-
Release the accelerator to slow down, and squeeze the brake lever for a sudden brake.
-
Tilt your body to the steering direction as you turn, and slowly turn the handlebar.
-
Put down the kickstand when parking. To avoid others using the scooter without your permission, you can lock the scooter when it is parked.
Lock & Unlock Your Scooter
- When the scooter is locked, the motor is locked and all the icons on the control panel will automatically go out except the Bluetooth icon and the lock icon.
- If the scooter goes beyond the Bluetooth connection range, the Bluetooth will be disconnected and its icon will go out.
- After the scooter is locked in the app, the motor will be locked and the power button will not function. If the scooter is moved forcibly, its front wheel cannot move normally, and it will have a rolling resistance accompanied by the buzzer alarm and a vibrating alert on the phone.
- This function cannot prevent the scooter from being stolen, please keep your scooter safe. The scooter will automatically turn off after 24 hours of being locked, and it will remain locked when turned on again.
- To unlock the scooter, tap “Unlock” in the app. Locking the scooter will consume the scooter’s power, please use this function wisely.
Note: The phone will vibrate only if the page of the scooter in the Mi Home/Xiaomi Home app is open.
Fold/Unfold & Carry
- Make sure the scooter is turned off and not being charged before folding. Hold the stem, lift the quick-release lever lock, and pull the quick-release lever outward.
- Lift the quick-release lever lock again, and pull the quick-release lever outwards to pop the bottom folding hook out. Then fold the stem.
- Align the buckle with the hook and together.
- Hold the stem with either one secure hand or both hands to carry.
- When unfolding the scooter, pull the buckle upwards to release it from the hook.
Adjust the Disc Brake
- Tool: 10 mm wrench (the tool needs to be prepared by the user).
- Before adjusting, make sure the scooter is turned off and not being charged. During adjusting, pull the end of the brake line to make the line tight.
- Note : If the brake is too tight, use the tool to loosen the screw by turning it counterclockwise, pull the disc brake rocker arm outwards, and then tighten the screw. If the brake is too loose, use the tool to loosen the screw by turning it counterclockwise, push the disc brake rocker’s arm forwards, and then tighten the screw.
Inflate the Tire
- Connect the pump to the extension nozzle.
- Inflate the tire.
- Remove the tire valve cap, and connect the extension nozzle and the valve securely together.
- Check the tire pressure every month, and inflate the tires if the pressure is too low. The recommended tire pressure is 45–50 psi.
Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual products and functions may vary due to product enhancements. For further information, please go to www.mi.com For detailed e-manual, please go to www.mi.com/global/service/userguide
This QR code is unique to your scooter and can also be found on the labels attached to the control panel and to the right side of the deck. It is used to connect the scooter with the Mi Home/Xiaomi Home app and contains important information about activating your scooter. Please keep this code safe.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>