ELECTCOM 2.0 CH HDMI DVD Player Instruction Manual

ELECTCOM 2.0 CH HDMI DVD Player

Features

| | | |
---|---|---|---|---

HDMI Cable

| RCA Cable|

Remote Control

| Instruction Manual|

Warranty Card

Important safety instructions: read carefully and keep for future reference.

Product Overview

Front Panel

1. USB PORT: Plug in USB
2. OPEN/CLOSE BUTTON: Open/close tray
3. PLAY/PAUSE BUTTON: Play start/play pause
4. STOP BUTTON: Return to the beginning of playback
5. POWER: Power on/off
6. LED DISPLAY: Displays the playing time.

Rear Panel

1. COMPONENT VIDEO(Y.Pb/Cb. Pr/Cr) OUTPUT: Video signal output interface
2. HDMI DIGITAL OUTPUT: HD Video signal output interface
3. L/R CHANNEL OUTPUT: Audio output interface
4. VIDEO OUTPUT: Video output interface.

Using the Remote Control

1. POWER ON/OFF
   Press to Power On, press again for Standby mode.

2. NUMBERS 0-9/10+
   While playing DVD/VCD/CD/MP3 discs, use key to select desired track/chapter in menu selection.

3. TITLE
   When using DVDs, press to return to the title menu.

4. ▲ ◀ ▼ ▶
   Select the direction within the menu.

5. ENTER
   Confirm your selection.

6. SETUP
   Press to get into SETUP menu.

7. OSD
   Press for the relative information of the disc to Display.

8. L/R
   When playing VCD or CD discs. Press button to select left or right channel, or stereo.

9. OPEN/CLOSE
   Press to load and remove discs.
   Place disc into tray with the title side facing up. Press button again to close the disc tray.

10. GOTO
    Press GOTO button to select title time, chapter time and track time. You can use digit keys to input the go to the specific time.

11. MENU
    When playing DVD discs press MENU once to return to sub menu. Press MENU again to return to the main menu.
    When playing VCD discs, press MENU button to turn on PBC, the VCD is n played by menu, press MENU button again to turn off PBC, then VCD is played in sequence.

12. REPEAT
    Press REPEAT button to repeat a title, chapter, track or the whole disc.
    When playing DVD discs, press REPEAT button continually, the TV screen shows chapter repeat, title repeat, all repeat, repeat cancel in turn.
    When playing SVCD, VCD , CD discs, the sequence is track repeat, all repeat, repeat cancel.
    When playing MP3 discs, the sequence is single repeat, directory repeat, repeat cancel.

13. VOLUME+ / VOLUME
    Increase/decrease volume.
    Remote control operation

    • Insert the batteries into the battery compartment. Point the remote at the remote sensor in front if the player. Make sure that there are no obstacles in the way between the remote and the player.
    • Take the batteries out of the remote control if it is not going to be used for a long time.

14. PLAY/PAUSE
    Press once to pause, press again to play.

15. STOP
    Press to stop media. Press the Play/Pause button to resume.

16. SUBTITLE
    When playing the DVD discs with multi-subtitles, press SUBTITLE continually to get to the language you desire.

17. ANGLE
    Change angle in DVD mode.

18. PREV (PREVIOUS,I <<)
    In DVD mode, press to go to previous chapter. With SVCD, VCD, CD, MP3 discs, press to go to previous track.

19. NEXT (NEXT, >>I)
    In DVD mode, press to go to next chapter.  With SVCD, VCD, CD, MP3 discs, press to go to next track.

20. REWIND( )
    Press this button for quick rewind search.

21. FORWARD( )
    Press this button for quick forward search.

22. DISC/USB
    Press this button to switch the play between DISC and USB.

23. SLOW
    Press to select slow speed playing.

24. LANGUAGE
    When playing DVD with more than one audio stream, press
    LANGUAGE to select what you desired.

25. CD RIPPING
    Press the button to use the CD ripping function.

26. PROG
    If the disc is with 2 or more tracks, chapters or titles, set up the playing order as your reference. Press this button to enter program menu.
    Press digit key to input the number of the track, title or chapter, If the programmed tracks are over ten press 10+ to go on programming.
    (Maximum 16 programmable items) use the up / down / left / right key to move the cursor to the PLAY. Press ENTER to start Program play.

27. HD
    Press the button to choose the following resolution levels from the HDMI output.

28. A-B
    Press to repeat certain sections.Press button on start point (A) and the end point (B) to select section. Cancel by pressing button a third time.

29. ZOOM
    Press to zoom in, press again to zoom out. Use arrow keys to move picture.

30. MUTE
    Mute the sound during playing.

31. N/P
    Press to switch the TV system between NTSC and PAL.

Connecting the DVD Player

Video system connection

Composite Video
Use the AV cable (yellow terminal) to connect composite video output of this unit to the TV/monitor video input.
Component Video
Use 3-core AV cable to connect the component output terminals of this unit to the corresponding TV/monitor input.
HDMI Output
Use a HDMI cable to connect the HDMI output to the HDMI input terminal.

Note!!!:

• Which connection to use depends on the TV/monitor input terminal.
• Do not use all the connections at one time, otherwise the picture will be affected.
• Only the physical connection conforms to the video setting can produce the normal picture. (Please refer to the Video Setup in System Setup)
  
  

Audio connection system

Stereo Audio
Use a pair of AV cables (red for right/white for left) to connect the stereo audio output of this unit to the TV if you want to have sound from the TV.
Note!!!:

• The physical connection should match with audio output setup of this unit. Please refer to Audio Setup in System Setup.
  

Setting the DVD Player

Basic Operation
Press on the remote control unit to setup the initial setting, select related[SETUP PAGE] with the directional buttons.
Menu Operations
You can setup the mode of audio and video output, initial setup, parental control level, etc. You can also select the aspect ratio of the playback picture to your TV screen. Press to display the setup menu and the system will automatically stop play.

System Setup

Press and select system setup page.

• TV SYSTEM: Use ▲ ▼ arrow buttons to make TV system selection. There
  are four TV output systems to choose from: NTSC, PAL, PAL-M and AUTO.

• HD OUTPUT: Use ▲ ▼ arrow buttons to set video resolution, there are three resolution(720P, 1080I, 1080P).

• VIDEO: There are different video output modes to choose from:

• INTERLACE-YUV: Use Y Cb Cr terminals to output signals.

• P-SCAN YPBPR: Use Y Cb Cr terminals to output signals and convert to progressive output.

• TV TYPE: Using arrow button to select TV aspect ratio.
  ◆ 4:3/PS:
  Pan & Scan video output for a normal TV set. The screen displays the wide picture on the wide screen with a left and right portion automatically cut Off.
  ◆ 4:3/LB:
  Letter Box video output for a normal TV set. The screen displays the wide picture with bands displayed on the upper and lower portions of the Screen.
  ◆ 16:9:
  Wide screen video output for a wide screen TV set.

• PASSWORD
  The initial setting of this item is under locked status. You can not set the rating and also can not change password . Input initial password: 0000 and press to confirm and then you can set rating and change password.

• RATING
  Playing some DVD discs can be limited depending on the age of the users. The parental control function allows playback limitation level to be set by the parent from level 1 to level 8. The level is from high to low. Level 1 is the lowest level and level 8 is the highest lever. This function is only valid for some DVD discs that have the limit level. And you should set the password first and make sure the password lock is locked.

• DEFAULT
  Use the arrow button to select [RESTORE] and press to return all the settings of the system to the original settings.

Language Setup

• OSD LANGUAGE

• AUDIO LANGUAGE

• SUBTITLE LANGUAGE

• MENU LANGUAGE
  

• Use ▲ ▼ arrow buttons to select desired language and press to confirm.
  If the selection is invalid, it means that the language is not available for this disc.

Audio Setup

• AUDIO OUT:
  Use arrow button to select the audio output way. This is the way for you to select SPDIF/OFF, SPDIF/RAW, SPDIF/PCM.

• KEY :
  Press ▲ ▼ to adjust the tone level.

Video Setup

• BRIGHTNESS
• CONTRAST
• HUE
• SATURATION
• SHARPNESS
  Use ▲ ▼ to adjust the corresponding value of the video output.

Speaker Setup

• DOWN   MIX LT/RT: When you play a disc that has logic effect, you can choose LT/RT output. The disc information will be decoded and show better effect.
• STEREO: When 2ch output is selected, normal stereo signals may be played from the L&R output socket.

Digital Setup

OP MODE
LINE OUT: The input signals are linear compressed and the volume is lower. You should rather choose LINE OUT setting at night. RF REMOD: The volume is higher and adapt to daytime use.
DYNAMIC RANGE
When you choose LINE OUT mode, select DYNAMIC RANGE to adjust the compression ratio and you can get different effects. When you adjust to FULL, the compression ratio will be set to the lowest level. When adjust is OFF, the compression ratio will be set to the lowest level.
DUAL MONO:
You can set the audio output mode for Left or Right channel. There are four modes: STEREO, MONO L, MONO R, and MIX MONO.

Playing the DVD Player

Playable file format

Supported discs format:
DVD, DVD+RW, DVD-RW, DVD+R, DVD-R, HDCD, VCD, CD, CD+R, CD-R, MP3 Music CD, Super VCD, CD-R/-RW.

Note!!!:

• It may not be able to play all the media discs in some cases due to the type of discs ( Especially for those DVD±R/RW discs), of which the method or device of the recording and how these files were created would distort the original contents and format.
• This unit does not guarantee the connection with all the USB devices.
• The USB port does not support USB charging.
• FAT and FAT32 files systems are supported.

Play Picture CD Disc

Press▲ ◀ ▼ ▶to select the desired picture.

Play MP3 Disc

• When playing a MP3 disc, there is a menu screen on TV press the [▲] or [▼] button to shift the cursor to select the track or folder and press ****the [ENTE button to play the selected track or folder (it needs to enter the sub-folder to select the track and press the button to play for some MP3 discs).
• Also use the digit button to select the track.

USB Operations

Remove the DVD/CD disc from the tray, insert the USB drive into the USB jack. The player will automatically detect the readable files in the USB drive. Use remote control to select the files for playback. (USB file unreadable means no supported file in USB.)

CD Ripping

The product has CD ripping functions.

• Put a CD into the disc tray and then plug in an USB drive.
• Press ****key on the remote. A CD rip menu will be shown on the TV screen.

Options

• First, select the copying SPEED normal or fast when normal is selected, you can listen to the music while copying is in process. When fast is selected you will only see the copy process in the TV screen.
• Second, select the BITRATE. Usually, 128K rate is used.
• Third, CREATE ID3 TAG. If the CD music files have the song name or singer name, you can build the ID3 information.

Tracks

• Move the cursor to right hand side. Select the song that you want to record. When it is selected, a Tick will be shown. If you move the cursor down to choose Select All, all the songs on the list will be copied. If selected none is chosen, any selected songs will be canceled. Move the cursor to the left side to select Start, press key to confirm. Then the copying will start.
• You will see the next menu page which shows the copying is in process. Move the cursor to the left side to select QUIT, press key.
• Exit RIPPING function.
• Play MP3 songs, press the button, put MP3 songs directly copied to the USB device.
• MP4 video playback, in the stop state, press the button, video to MP4 directly copied to the USB device.

Note

1. Make sure the USB drive has enough memory space for the music files.
2. The copied files are in MP3 format only.

Safety information

Important Notes:

• Please read through the manual carefully before connecting and operation. Do not open the cover or touch any internal components for non-professional. Turn off the power when the unit is not being used.
  (Unplug the power cord if the unit is not used for a long time.)

• Do not expose the unit to direct sunlight.

• Keep away the heating sources or equipment.

• Do not expose the unit to moisture.

• Place the unit on a horizontal level. Keep the unit ventilated. Don’t block the heat hole. Overheat may cause malfunction.

• Clean the cabinet with soft cloth Detergent or alcohol is forbidden.

• This book is only a guide for user’s operation not a criterion for configuration. This apparatus shall not be exposed to dripping or splashing and that no object filled with liquids, such as vases, shall be placed on the apparatus.

The lightning flash is intended to alert the user to the presence of dangerous voltages within the product’s enclosure, and touching the inner parts may result in a risk of electric shock to persons.
The exclamation mark is intended to alert the user to the presence of important operating instructions.
To reduce the risk of electric shock or fire, do not open the cover. Refer servicing to qualified service personnel.
This mark indicates that this unit contains a class 1 laser product. The laser beam may produce harmful radiation if it directly touches the human body.

Specification

20Hz~20KHz
S/N ratio| ≥60 dB
Audio dynamic range| ≥60 dB
Operating conditions| Temperature: 5-40°C, operation flat, horizontal
Video output| 1.0V(P-P).75Ω
Audio output(analog audio)| 2.0V(rms)

Troubleshooting

If you experience any of the following difficulties while using the player, use this troubleshooting guide to help remedy the problem before requesting repairs.

both the TV and the DVD player are powered on
Sound| There is no sound| Audio cable does not connect well| Connect the cable properly
Power off the connected equipment| Turn on power
Audio setup is not correct| Select the suitable audio setup
In fast forward/rewind playback mode| Stop fast forward/rewind playback mode
The volume is low| Volume down| Press “VOL+” on the remote control to increase the volume or increase the TV volume
System is in LINE OUT setting| Press the SETUP button on the remote control to set the mode. SETUP——Digital Setup——OP MODE ——RF REMOD
Picture| There is no picture| TV video setup is not correct| Select the TV suitable setup
Video cable does not connect well| Connect the cable properly
No signal connection| Make signal connection settings for TV
The picture is distorted| Dirty disc| Clean the disc
In fast forward or fast rewind mode| Stop fast forward/rewind playback mode. Sometimes, the tiny distortion appears. It is normal
Brightness or picture instability| Anti-copy circuit influence| Connect the DVD unit to TV directly
Play| I can’t play the disc| Disc format not supported| Blu-ray discs are not supported, you can check the disc formats supported by P9
Without disc| Put in the disc
Disc is put upside down| Put the disc property
The disc is dirty or bad| Clean or replace the disc
There is menu on TV screen| Use SETUP to turn off menu
Parental control is working| Set up parental off or change the setup
Device| The button not working| Power wave or other sialic interference| Turn on/off the power and try again
The disc tray doesn’t work| Disk tray injects and ejects repeatedly| Power off. Unplug the power cable and wait for 30 seconds. Plugin the power cable and try again
Disk tray does not open|

1. Power off. Unplug the power cable and wait for 30 seconds. Plug in the power cable and try again
2. Press ‘POWER’ and ‘EJECT’ in the same time

Remote control| The remote control doesn’t work| Remote control is not pointed at the sensor| Point the remote control at the sensor
Remote control is too far from DVD unit| Operate the remote control within 7m and make sure no obstacles in between
Batteries are exhausted| Replace the batteries

Warranty

Register Your Product

Returns and Replacement
Easy returns and free replacements after the return window expires!
Customized Support
Get assistance quickly with your information on hand.
News and Offers
Stay up-to-date with product updates and offers.

Scan the QR code to get it!

Customer Service

Need help with:

• Connecting your devices
• Product setup
• Return & Replacement
• Technical support
• More information

| |
---|---|---

Email Support

| Live Chat|

Amazon Message

Email: SUPPORT@ELECTCOM.CO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>