Synology RT6600AX Tri-Band Mesh 11ax Router Installation Guide

Synology RT6600AX Tri-Band Mesh 11ax Router

Before You Start
Thank you for purchasing this Synology product! Before setting up your new expansion unit, please check the package contents to verify that you have received the items below. Also, make sure to read the safety instructions carefully to avoid harming yourself or damaging your expansion unit.

Note: All images below are for illustrative purposes only, and may differ from the actual product.

Package Contents

| **
RJ-45 LAN cable x 1**

Synology WRX560 at a Glance

1

| STATUS Indicator| ****

Front Panel

| Displays the status of the system.

2

| WAN Indicator| Displays the status of WAN connection.

3

| Wi-Fi Indicator| Displays the status of Wi-Fi connection.

4

| ****

WPS Button

| ****

Right Panel

| Press to start WPS.
5| Wi-Fi Button| Press for three seconds to turn on/off the Wi-Fi network.

6

| USB 3.2 Gen 1

(Type-A) Port

| Connect an external drive, USB printer, or other types of USB devices here.
7| Power Button| ****

Rear Panel

| Press to power on/off the Synology Router.
8| Power Port| Connect the AC power adapter here.
9| WAN Port| Connect a network cable from the ISP modem into this port to establish WAN connection.
10| 2.5G WAN/LAN Port| 1.  Connect a network cable from the ISP modem into this port to establish WAN connection.

2.  Connect network cables into these ports to establish LAN connection

11| LAN Port| Connect network cables into these ports to establish LAN connection.
12| RESET Button| Press and hold for four seconds (Soft Reset) or for ten seconds (Hard Reset).

LED Indicator Table

Status Indicator

| ****

Green

| Static| Powered on
Blinking| System Ready

Orange

| Static| System booting/Rebooting/Hard Reset
Blinking| Mesh network disconnected
Green/Orange| Blinking| Searching device
Off| Powered off

Wi-Fi

| ****

Green

| Static| Wi-Fi active
Blinking| WPS connecting
Off| No Wi-Fi

WAN

| ****

Green

| Static| Network connected
Blinking| Data transmitting
Off| Network disconnected

Hardware Specification

WAN Port

| •  Gigabit WAN x 1

•   Gigabit WAN x 1 and 2.5G WAN x 1 (Dual WAN)

LAN Ports

| •   Gigabit LAN x 3 and 2.5G LAN x 1

•   Gigabit LAN x 3 (Dual WAN)

Size (H x W x D) (mm)| 233 x 194 x 66
Weight (kg)| 1 kg
Supported Clients (for SRM management)| •  Windows 7 onwards

•   Mac OS 10.12 onwards

File Systems| External: EXT4, EXT3, FAT, NTFS, HFS+

Wireless Standards

| • 2.4GHz: 802.11 b/g/n/ax

• 5GHz: 802.11 a/n/ac/ax

Operating Frequency Range

| •   802.11ax (2.4GHz): Up to 600 Mbps

•   802.11ax (5GHz): Up to 2400 Mbps

Wireless Operation Modes

| •   Wireless Router

•   Wireless AP (Access Point)

Wireless Security

| •   WPS support

•   WPA2-Personal • WPA/WPA2-Personal

•   WPA2-Enterprise • WPA/WPA2-Enterprise

•  Opportunistic Wireless Encryption (OWE)

•   WPA3-Personal • WPA3-Enterprise

•   WPA2/WPA3-Personal

Antennas

| •   2T2R Omni-directional high-gain dipole (2.4GHz)

•  4T4R Omni-directional high-gain dipole (5GHz)

Buttons & Switches| •   Power • WPS • Wi-Fi On/Off • Reset/Login

Language Localization

| ****

Environment Requirements

| •   Line voltage: 100V to 240V AC

•   Frequency: 50/60Hz

•  Operating Temperature: 40 to 104˚F (5 to 40˚C)

•   Storage Temperature: -5 to 140˚F (-20 to 60˚C)

•   Relative Humidity: 5% to 95% RH

Note: Model specifications are subject to change without notice. Please refer to www.synology.com for the latest information.

Safety Instructions

|

Keep away from direct sunlight and away from chemicals. Ensure a stable environment with no abrupt changes in temperature or humidity.

---|---

| ****

Place the unit right side up at all times.

|

Keep the unit away from liquids.

|

Before cleaning, unplug the power cord. Do not use chemical or aerosol cleaners. Wipe with damp paper towels.

|

To prevent the unit from falling over, do not place it on carts or any unstable surfaces.

|

The power cord must plug into the correct supply voltage. Ensure the supplied AC voltage is correct and stable.

| ****

Warning, electric shock hazard. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.

|

Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries appropriately.

| ****

Power cord must be plugged into a socket-outlet with earthing connection.

|

Keep body parts away from moving fan.

|

This product must be installed by qualified personnel in a restricted access location (like dedicated equipment rooms, service closets).

Hardware Setup

Position Your WRX560
For optimal performance, it is recommended to position your WRX560 as advised below:

• On a stable surface (e.g. an elevated shelf) away from any possible physical interruptions.
• Close to the center of the area where the wired/wireless client devices are placed, and within a visible distance from the wireless devices.
• In a position where few walls and ceilings are between your WRX560 and its client devices.
• Away from any potential electrical signal sources, such as other Wi-Fi routers, 3G/4G bases, and microwave ovens.
• Away from large expanses of metal or other materials, such as metal doors, glass panels, and concrete.

Connect to Your WRX560

1. 1 Use the included network cable to connect your WRX560 (at the WAN1 port) to the ISP modem. Connect one end of the power adapter to the power port on your WRX560, and the other end to the power outlet. Press the power button to power on your WRX560. Wait for up to two minutes until the STATUS and WAN LED indicators turn green.

2. Connect wireless client devices to your WRX560. When the Wi-Fi indicator has turned static green, WRX560 is ready to connect with other devices. Use your wireless device to scan and join the Wi-Fi network created by your WRX560.
   Note:
   The default credentials for the Wi-Fi network:

   • Wi-Fi SSID: Synology_(Serial)
   • Password: synology
     You can change it during the initial SRM setup.

3. Connect wired client devices to your WRX560. Use network cables to connect devices to the LAN ports. The corresponding LAN LED indicators should turn orange/green to indicate successful connection.

4. Reset/Login Instructions.

Mount Your WRX560

• Do not install the device in an unstable location, such as on an unsteady table or an inclined surface.
• Do not place another hub or object that generates heat on top of this unit.
• Please route all cables properly to prevent people from tripping over them.
• Ensure the air vents on the product are not blocked by other equipment or walls.
• Only use the power cable included with the product. Using other power cables may result in damage or fire.
• Use 2 screws (not included) with the dimensions shown below.
• The screw head should project out from the wall at 7mm.

Set up Synology Router Manager (SRM)

1. Use a computer or wireless device connected to your WRX560 ‘s local network. If you use a wireless device,scan and join the Wi-Fi network (SSID: Synology_(Serial); Password: synology).
2. Open a web browser, and enter either URL into the address bar:
   • http://router.synology.com
   • http://192.168.1.1:8000
3. Once connected, click Start to launch the SRM Setup Wizard.
4. Fill in the information to set up the administrator account. Click Next to continue.
5. Fill in the information to set up the Wi-Fi network. Click Next to continue.
6. Set up the operation mode. When choosing the Wireless Router mode, you can also enable External access to SRM so that only external access via the HTTP(S) port (e.g. 8000/8001) can reach SRM.
7. Choose an Internet connection type:
   • PPPoE: Choose this option if you have obtained PPPoE credentials from the ISP.
   • Manual IP: Choose this option if you have obtained an available IP address for use.
   • Auto IP: Choose this option if you rely on an ISP modem for automatic IP assignment.
   • 
8. The wizard will continue to set up your WRX560, and it may take up to three minutes to complete the setup.
9. After the setup is complete, click Start managing now to enjoy SRM and its various features.

Note

1. Above is a general demonstration of the SRM setup steps. The steps and available options may somewhat vary depending on your device type (e.g. PC or wireless device), access type (LAN, WAN, or Wireless LAN), and chosen operation mode (Wireless Router or Wireless AP).
2. If the setup is to be completed with a wireless device, remember to download DS router to manage your RT3000ax from anywhere.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.
FCC regulations restrict the operation of this device to indoor use only.

Industry Canada statement:

This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution :

1. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2. where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body.

RED Compliance Statement
Compliance with 2014/53/EU Radio Equipment Directive (RED)
In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the EU:

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

| AT| BE| BG| HR| CY| CZ| DK|
---|---|---|---|---|---|---|---|---
EE| FI| FR| DE| EL| HU| IE|
IT| LV| LT| LU| MT| NL| PL|
PT| RO| SK| SI| ES| SE| UK| UK(NI)

This device is restricted to indoor use

References

• Why can't I find my Synology Router via router.synology.com? - Synology Knowledge Center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>