Nile Global NWA1050 Outdoor Wireless AP Instruction Manual

Nile Global NWA1050 Outdoor Wireless AP Instruction Manual

Nile Global Inc. Outdoor Wireless AP

Product Specification

Bluetooth 2.4GHz
Operation frequency 2.4GHz 5GHz Bluetooth low energy(V4.1)| 2412~ 2462MHz 51805850MHz 2402~ 2480MHz
Networking interface| 1x5G mGig Ethernet port
Max power consumption| 35watts
Max Tx Power| Wi-Fi 2.4GHz band: 21dBm(per chain)Wi-Fi 5GHz band: 21dBm(per chain)BLE: 7dBm
MTBF| 356,126 hours
Power source| Power over Ethernet(PoE): 802.3bt
Mounting mode| Wall/Ceiling/Pole
Operation temperature| -40~+65 C
Operation humidity| 5-95% Noncondensing
Altitude| 10,000ft (3,048m)

Installation of ceiling plate + AP on T-bar (9/16″ & 15/16″) Please update accordingly

Step 1. Align T-bar Wit Felling plate

Step2. Slide ceiling plate/ AP together until T-bar under slots of g plate.

Step2. Slide ceiling plate/ AP together until T-bar under slots of ceiling plate.

Un installation of ceiling plate + AP from T-bar (9/16″ & 15/16″) → please update accordingly

Step1. Press the lock plunger and move bracket B left to unlock it.

Step2. Slide ceiling plate/ AP together from slots of ceiling plate.

Installation of RJ45 cable on ceiling plate

Step1. plug cable into RJ45 of AP. –

Step2. put cable into cable slot of ceiling plate.

Installation of ceiling plate + AP on wall mount

Step1. Move bracket B to lock it with bracket A

Step2. Hang the product/ceiling plate together on the wall.

Regulatory Compliance Information:

Safety Notice

• Please use CSA/UL Certification Approval & LPS’s External Power Adaptor.
• Please connect with CSA/UL Certification Approval & LPS’s DC Source.
• NWA1050 is outdoor use Wireless AP.
• There is a risk of fire if the battery is replaced with an incorrect type.

Professional installation instruction.

1. Installation personal«
   This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.«

2. Installation location«
   The product shall be installed at a location where the radiating antenna can be kept – from nearby person in normal operation condition to meet regulatory RF exposure requirement.«

3. External antenna«
   Use only the antennas which have been approved by the applicant. The non- approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited.«

4. Installation procedures
   Please refer to user’s manual for the detail.~

5. Warning«
   Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty.«

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

FOR MOBILE DEVICE USAGE ( >20cm/low power)

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance – between the radiator & your body.

Industry Canada statement

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution :

(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725 5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; (detachable antenna only)

FOR MOBILE DEVICE USAGE ( >20cm/low power)

Radiation Exposure Statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20 cm between the radiator & your body.

Accessory List

Pole Mount Process

Step 1. Pass the hose clamps through the slots on the stand, attach the stand to the pole and tighten the clamp using a screw driver to twist its screw head

Step 2. Put Cairo on the stand. Fix Cairo with M6 screw, spring & washer (toque 2.5N-m recommended)

Step 3. Release screw , adjust vertical angle and screw it back

Screw back according to circle symbol to fix angle (toque 2.5N-m recommended)

Step 4. Release screw ,adjust horizontal angle and screw it back.

Screw back according to triangle symbol to fix angle (toque 2.5N-m recommended)

Step 5. Re-secure M10 bolt (torque 12N-m recommended)

Step 1. Use screws and plastic anchors to fix stand to the wall and repeat step 2 to step 5 in the pole mount process.

Cable Gland Assembly Process

Documents / Resources

| Nile Global NWA1050 Outdoor Wireless AP [pdf] Instruction Manual
PD5-NWA1050, PD5NWA1050, NWA1050, NWA1050 Outdoor Wireless AP, Outdoor Wireless AP, Wireless AP
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>