Skullcandy 2SKSK1849 BARREL Fully Immersive Sound For You and Your Crew User Guide
- June 13, 2024
- Skullcandy
Table of Contents
Skullcandy 2SKSK1849 BARREL Fully Immersive Sound For You and Your Crew
User Guide
FRONT PANEL
BARREL
FULLY IMMERSIVE SOUND FOR YOU AND YOUR CREW
BACK PANEL PORTS:
- AUX 3.5MM AUDIO INPUT
- USB-A AUDIO INPUT / POWER OUTPUT
- USB-C POWER OUTPUT
- DC POWER INPUT
*PORT COVER MUST BE CLOSED TO ALLOW FOR IPX5 WATER PROTECTION
FUNCTIONS
Power ON / OFF:
Press and hold the “O” button for 2s. If not connected to a Bluetooth® device
or connected but idle (not playing audio) the speaker will turn OFF
automatically after 15 min.
Play / Pause:
Press the “ ” button once to play or pause audio.
Volume up:
Press “+” button to increase the volume.
Volume Down:
Press “-” button to decrease the volume.
Next Track:
Press and hold “+” button for 2s to skip track.
Previous Track:
Press and hold “-” button for 2s to go to last track.
Bluetooth® Pairing:
First disconnect the speaker from any AUX or USB-A inputs. Then press and hold
the “Bluetooth®” button for 2s to enter Bluetooth® Pairing Mode. The speaker
will disconnect from any paired device and will become available to pair to
new devices. The speaker will stay in pairing mode for 60s, or until
connected. Status LED will blink blue while in Bluetooth® Pairing Mode.
True Wireless Stereo Pairing:
Press the “O” button three times to pair any two Barrel™ speakers to play
audio in stereo. Status LED will be cyan to indicate Right channel and yellow
to indicate Left channel (before TWS pairing, make sure that only one of the
speakers is connected to an audio source).
Exit True Wireless Stereo Mode:
Press the “O” button three times to exit TWS pairing.
SKDY Multi-link™ Transmitting:
First, connect one Barrel™ Speaker to Bluetooth®, AUX, or USB-A audio input.
Then press and hold the “ ” and “+” button together for 1s to set the speaker
as transmitting. Status LED will be purple.
SKDY Multi-link™ Mode Receiving:
First, disconnect the speaker from any Bluetooth® device by pressing and
holding the Bluetooth® button for 2s. Disconnect the speaker from any AUX or
USB-A inputs. Then press and hold the “ ” and “+” button together for 1s to
set the speaker as receiving. Status LED will be green. Up to 99 receiving
speakers can be connected to a single transmitting speaker.
Check Battery Status:
The 4 LED indicators show the battery level. Press and hold “+” and “-“
buttons together for 1s to initiate a voice prompt of the battery level.
Bass Boost
Bass Boost – Press and hold the “Play” button for 2s to toggle Bass Boost mode
ON/OFF. The “ ” button will be illuminated while the speaker is in Bass Boost
Mode.
Light Show ON/OFF
Press and hold the “Light Show” button for 2s.
Light Show Change Mode
Press the “Light Show” button once to cycle between the light show modes.
Dual-Device Connection:
You can pair two transmitting devices (mobile phones for example) to the
Barrel™ speaker at the same time to DJ together. Pause the music on the first
device to play a song from the second device.
Charge Out:
While the speaker is ON: Plug in a USB-C™ or USB-A cable to begin charging
your compatible portable device automatically.
CHARGING THE BARREL™
Use the included charging adapter to connect the speaker to an appropriate power source to begin charging. The LED indicators will show the battery is charging. When all 4 LEDs are ON, the battery is fully charged.
Warning:
- To avoid damage to the speaker and battery, it is important to only use a power source that matches the power requirements listed on the speaker’s rating label.
- To avoid overheating, it’s recommended not to place the speaker in direct sunlight, especially while charging and playing music.
Battery Status Indication (not charging):
- 0-5% – speaker is OFF all 4 LEDs are OFF
- 5-10% – 1st LED blinks red, other LEDs are OFF
- 10-25% – 1st LED is ON white, other LEDs are OFF
- 25-50% – 1st + 2nd LEDs are ON white, other LEDs are OFF
- 50-75% – 1st + 2nd + 3rd LEDs are ON white, other LEDs are OFF
- 75-100% – All LEDs are ON white
Battery Status Indication (while charging):
- 0-25% – 1st LED blinks white, other LEDs are OFF
- 25-50% – 1st LED is ON white, 2nd LED is blinking. Other LEDs are OFF
- 50-75% – 1st + 2nd LEDs are ON white, 3rd LED is blinking. Other LEDs are OFF
- 75-99% – 1st + 2nd + 3rd LEDs are ON white, 4th LED is blinking. Other LEDs are OFF
- 100% – All LEDs are ON for 1 minute, then OFF
CONNECTION PRIORITY
AUX > USB > BT (Bluetooth®)
To play from an AUX source, simply plug in an AUX cable to the speaker and your audio source device. It will automatically have priority over USB and BT. To play from a USB source, plug in a USB flash drive and make sure that AUX is disconnected. It will automatically have priority over BT (but not over AUX). To play from BT source, connect a Bluetooth® enabled device and make sure that AUX and USB are disconnected.
TROUBLE SHOOTING
Factory Reset:
Press and hold “-” and “+” buttons at the same time for 10s to initiate
factory reset. The speaker will revert to factory settings and all previously
paired devices will be deleted. Status LED will blink between blue and red
while resetting.
Speaker is not Playing Wirelessly:
If the speaker is not playing audio although it’s connected to a Bluetooth™
device, it may be because of the audio connection priority. Disconnect any AUX
or USB-A cables that may be connected to the speaker and try again.
SPECIFICATIONS
- Bluetooth® Version： 5.3
- Battery Capacity: 11.1V/4400mAh
- Charging Input: DC 22V/3.2A
- Play Time: Up to 12 hours*
- Charging Time: 3.5 hours
- Operating Range: 10M
- Rated Power: 60W
- Audio Inputs: Bluetooth®, USB-A, Aux 3.5mm
- Charging Outputs: USB-C, USB-A
- Battery Standby Time: 365 Days
- IPX Rating: IPX5 (water resistant)
STICKER PACK
BACK PANEL
Double sided pritning – Accordian Style Booklet
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Canada warning:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
2023© Skullcandy is a registered trademark Marketed and distributed by Lifeworks technology Group LLC., New York, NY 10018. USB Type-A™, USB Type-C™ and USB-C™ are trademarks of USB Implementers Forum. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Lifeworks Technology Group LLC. is under license. All brands are registered trademarks of their respective companies. Actual product may differ slightly from images. Battery playtime is based on 77 SPL (C), actual playtime will vary based on song type and playing conditions. Made in China.
SCAN FOR SUPPORT
Documents / Resources
|
Skullcandy 2SKSK1849 BARREL Fully Immersive Sound For You and Your
Crew
[pdf] User Guide
2SKSK1849, 2SKSK1849 BARREL Fully Immersive Sound For You and Your Crew,
BARREL Fully Immersive Sound For You and Your Crew, Fully Immersive Sound For
You and Your Crew, Immersive Sound For You and Your Crew, Sound For You and
Your Crew, Crew
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>