REELCRAFT 5605 OLP Spring Driven Hose Reels Instruction Manual
- June 13, 2024
- REELCRAFT
Table of Contents
Series 5005 Spring Driven Hose Reels
5605 OLP 5650 OLP
Low, Medium and High Pressure Model Numbers:
Dimensions
SAFETY
- Do not use reel at higher pressures or temperatures than listed on the back of this bulletin.
- Remove all spring tension before beginning disassembly process.
INSTALLATION:
A flexible hose connection must be used between the hose reel inlet and the
source of supply to prevent possible misalignment and binding.
MOUNTING:
The hose reel is equipped with a universal mounting bracket so that it can be
mounted on the floor, wall or ceiling; whichever place is convenient. The hose
guide arm can be moved to the position desired by removing the screws
fastening the guide bracket to the reel base. Shift the guide arm bracket so
the hose comes off the reel at the desired position and replace the screws.
NOTE: For proper installation in wall mount applications, ensure reel is
mounted with inlet on the right as you are facing the reel. Failing to do so
could cause latching issues.
LUBRICATION:
Hose reel spring and bearings are factory lubricated and require no further
lubrication.
REPLACING HOSE:
- Wind spool flange clockwise-facing swivel-until spring is tight.
- Back off three turns and latch.
- Insert hose through roller guide.
- Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS:
To adjust spring tension, add or remove wraps of hose from the spool, one wrap
at a time until desired tension is obtained.
REPAIRS:
Extensive repairs should be performed only by an authorized serviceman or
factory to avoid damage which may void your warranty. Remove all spring
tension before beginning disassembly process.
Series 5005 Spring Driven Hose Reels
Item #| Part #| # Req.| Description| Item #| **Part
| # Req.| Description| Item #| Part #| # Req.**|
Description
---|---|---|---|---|---|---|---|---|---|---|---
1| 300031| 2| 1” Snap Ring| 10| S500107| 1| Guide Arm Assembly| 19| S400018|
1| Latch Spring
2| 300034| 2| Spacing Washer| 12| S261360| 1| Spring Case Stud| 20| 400020| 1|
O-ring
3| S295-102| 3| Hex Screw| 13| 300006| 1| 3/8-16 x 1/2” Set Screw| 21|
S400109| 1| Latch Plate Assembly
4| 260149| 1| Reel Flange| 14| S600094| 1| Spring Case & Hub Assembly| 22|
2-117440| 1| U-Bolt Hose Clamp
5| 260151| 1| Sheave Disk| 16| 600029| 1| Base Assembly| 24| 261650-1| 2|
1/4-20 NY lock Nut
6| S500019| 1| Latch Cam| 17| S400021| 1| Latch Bumper| 30| S82-15| 9| Nylon
Nut 10-32 x 3/8”
7| S260648| 1| Spring Arbor| 18| S400012| 1| Latch Bushing| | | |
Item #| Description| # Req.| 5605 OLP| 5650 OLP
---|---|---|---|---
8| Bumper Stop Assembly| 1| None| 1-HR1004
9| Hose Assembly| 1| None| S601013-50
15| Drive Spring Assembly| 1| S600050| S600050
25| Main Shaft| 1| 602555| 602555
26| Swivel & Ell Assembly| 1| None| None
27| 90° Elbow| 1| None| None
28| 90° Elbow| 1| None| None
29| Swivel Assembly| 1| S600886| S600886
Hose I.D. and Length| None| 3/8” x 50’
Reel Inlet Connection| 3/8” F.P.T.| 3/8” F.P.T.
Max. Operating Pressure| 500 P.S.I.| 300 P.S.I.
Max. Operating Temperature| 210 °F| 150 °F
Form# 872-297 Rev: 2/2023
Reel craft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN
46725
Ph:800-444-3134 /
260-248-8188 • Fax:
800-444-4587 /
260-248-2605
Customer Service:855-634-9109 •
reelcraft@reelcraft.com •
www.reelcraft.com
www.reelcraft.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>