CAME 806LA-0010 LED Flashing Light Instruction Manual

CAME 806LA-0010 LED Flashing Light

General precautions for installers

Read the instructions carefully before beginning the installation and carry out the procedures as specifi ed by the manufacturer.

• Installation, programming, commissioning and maintenance must only be carried out by qualified, expert technicians and in full compliance with the applicable law.
• Before carrying out any cleaning or maintenance, or replacing any parts, disconnect the device from the power supply using the all-pole circuit breaker on the control panel up from the operator.
• Only use this product for its intended purpose. Any other use is hazardous.
• The manufacturer cannot be held liable for any damage caused by improper, unreasonable or erroneous use.
• The product, in its original packaging supplied by the manufacturer, must only be transported in a closed environment (railway carriage, containers, closed vehicles).
• If the product malfunctions, stop using it and contact customer services at https://www.came.com/global/en/contact-us or via the telephone number on the website.
• The manufacture date is provided in the production batch printed on the product label. If necessary, contact us at https://www.came.com/global/en/contact-us
• The general conditions of sale are given in the offi cial CAME price lists.

Dismantling and disposal

Dispose of the packaging and the device responsibly at the end of its life cycle, in compliance with the laws in force in the country where the product is used. The recyclable components are marked with the material symbol and ID.
THE DATA AND INFORMATION IN THIS MANUAL MAY BE CHANGED AT ANY TIME AND WITHOUT NOTICE.
MEASUREMENTS ARE IN MILLIMETRES, UNLESS STATED OTHERWISE.

Description

KRX1FXSO – LED fl ashing beacon, power supply 24 V AC – DC up to 230 V AC, with orange dome.
KRX1FXSW – LED fl ashing beacon, power supply 24 V AC – DC up to 230 V AC, with white dome.
KRX1FXSY – LED fl ashing beacon, power supply 24 V AC – DC up to 230 V AC, with yellow dome.

Technical data

230 AC
Operating temperature (°C)| -20 ÷ +55| -20 ÷ +55| -20 ÷ +55
---|---|---|---
Protection rating (IP)| 54| 54| 54
Frequency (MHz)| 433 and 868| 433 and 868| 433 and 868
Storage temperature (°C)| -25 ÷ +70| -25 ÷ +70| -25 ÷ +70
Average product life (hours)| 100000| 100000| 100000

• Before installing the product, keep it at room temperature where it has previously been stored or transported at a very high or very low temperature.
• The average product life is a purely indicative estimate. It applies to compliant usage, installation and maintenance conditions. It is also infl uenced by other factors, such as climatic and environmental conditions.
• The frequency 868 MHz is not available for the Russian market.

Description of parts A

1. Protective band

2. Flashing beacon

3. LED with built-in antenna

4. Self-tapping screw 2.2×9.5

5. Control board

6. Beacon base

7. Self-tapping screw 2.9×13

8. Jumper for flashing mode
   (*) Optional accessory.

9. Terminal board for connecting the antenna

10. Power supply terminal block

11. Rubber gasket

12. Wall-mounting support *

13. Self-tapping screws 3.9×13 *

14. Coaxial cable RG-58 *

15. Cable FROR 2×1 mm2
    () Accessory not supplied.

Size B

Installation examples C

• A Standard

• B C With wall-mounting support
  Installation
  

• D Remove the protective band and dome from the beacon base.

• E Remove the control board from the base.

• F Drill a hole in the beacon base.

• G Thread the power supply cable and antenna cable through the holes in the base. Fasten the base using screws and plugs.

• For information on wall-mounting, see fi gures H and I .

• J Fasten the control board to the base.

• K Connect the cables to the control board.

Keep the protective cable sheath close to the terminals.

The LEDs fl ash automatically when the board is powered up. Where the panel connection is via an intermittent power supply, cut the jumper 8 on the electronic board.
L Fix the dome in place and insert the protective band.

The contents of this manual may be changed at any time and without notice. Translation of the original instructions.

Tel. (+39) 0422 4940
Fax (+39) 0422 4941
info@came.com
www.came.com

References

• CONTACT US | CAME
• Homepage Installers | Came
• Homepage Installers | Came
• CONTACT US | CAME

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>