BYD HVM 8.3 High Voltage Battery-Box Premium System User Guide

BYD HVM 8.3 High Voltage Battery-Box Premium System

Product Information

Finnish, Dutch, Czech, Portuguese, Swedish, Lithuanian
Technical Parameters| Available at page 85 of the user manual
Legal Provisions| All the information in this document is the property of
Shenzhen BYD Electronics Co., Ltd. No part of this document could
be reproduced in any way for business use. Internal use is allowed.
Specifications are subject to change without notice. Every effort
has been made to make this document complete, accurate, and
up-to-date. However, Shenzhen BYD Electronics Co., Ltd. may need to
make some improvements under certain circumstances without advance
notice. Shenzhen BYD Electronics Co., Ltd. shall not be responsible
for any loss caused by this document.
Limited Warranty| You can download the current Limited Warranty from the Internet
at websites: BYD Global Service (www.bydbatterybox.com), BYD
service partner in Europe (www.eft-systems.de), BYD service
partner in Australia (www.alpspower.com.au). Shenzhen
BYD Electronics Co., Ltd. No.1, Yan’an Road Kuichong, Dapeng,
Shenzhen, Guangdong Province, 518118, P. R. China.

Product Usage Instructions

To operate the Be Connect 2.0, please follow these instructions:

1. Ensure that you have the Battery-Box Premium HVS 5.1, 7.7, 10.2, 12.8, or HVM 8.3, 11.0, 13.8, 16.6, 19.3, 22.1 with firmware version BMU 3.16 or BMS 3.24.
2. Connect the Be Connect 2.0 device to your Battery-Box Premium using the provided cables.
3. Power on the Battery-Box Premium.
4. Follow the on-screen instructions to set up and configure the Be Connect 2.0.
5. Once the setup is complete, you can use the Be Connect 2.0 to monitor and control your Battery-Box Premium.

Please refer to the user manual for detailed instructions on configuring and using the Be Connect 2.0.

Legal Provisions

All the information in this document is the property of Shenzhen BYD Electronics Co., Ltd. . No par t of this do cument could be reproduced in any way for business use. Internal use is allowed.
Shenzhen BYD Electronics Co., Ltd . makes no representations or warranties express or implied, with respect to this document or any of the equipment and/or software it may describe, including (with no limitation) any implied warranties of utility, merchantability, or fitness for any particular purpo se. All such representations or warranties are expressly disclaimed. Neither Shenzhen BYD Electronics Co., Ltd. nor its distributors o r dealers shall be liable for any indirect, incidental, or consequential damages under any circumstances.
The exclusion of implied warranties may not apply in all cases under some statutes, and thus the above exclusion may not apply.
Specifications are subject to change without notice. Every effort has been made to make this document complete, accurate, and up-to-date. However, Shenzhen BYD Electronics Co., Ltd . may need to make some improveme nts under certain circumstances without advance notice. Shenzhen BYD Electronics Co., Ltd . shall not be responsible fo r any loss caused by this document , including, but not li mited omissions, err ors, typographical errors, arithmetical errors, or listing errors in this document.
All trademarks are recognized.

Limited Warranty
You can download the current Limited Warranty from the Internet at websites:
BYD Global Service, www.bydbatterybox.com ,
BYD service partner in Europe, www.eft-systems.de ,
BYD service partner in Australia, www.alpspower.com.au.
Shenzhen BYD Electronics Co., Ltd .
No.1, Yan’an Road Kuichong, Dapeng, Shenzhen, Guangdong Province, 518118, P. R. China .

 Information on this Document

Validity
This document is valid for the Battery-Box Premium HVS 5.1, 7.7, 10.2, 12.8, and HVM 8.3, 11.0, 13.8, 16.6, 19.3, 22.1 from firmwa re version BMU 3.16, BMS 3.24.

Target Group
The instructions in this document may only be performed by qualified persons who must have the following skills:

• Knowledge of how batteries work and are operated
• Knowledge of how an inverter works and is operated
• Knowledge of, and adherence to the locally applicable connection requirements, standards, and directives*
• Knowledge of, and adherence to this document and the associated system documentation, including all safety instructions
• Training in dealing with the hazards associated with the installation and operation of electrical equipment and batteries
• Training in the installation and commissioning of electrical equipment

Failure to do so will make any manufacturer’s warranty, guarantee or liability null, and void unless you can prove that the damage was not due to non- compliance.

Content and Structure of this Document
This document contains safety information and instructions on installing, connecting, and commissioning. Please finish reading this document before taking any actions on the battery system.
The latest version of this document and the manual for installation, commissioning, and operation are to be found in PDF format at our websites.
This document only contains brief information and may deviate from the real system.

 Safety

Intended Use
The battery system is for residential and works with a photovoltaic system. It is a high voltage Li-ion battery storage system, with the control module on itself.
The system could be connected with the Internet through network cable for maintenance and software updates.
The system must only be used as stationary equipment.
The system is suitable for indoor and outdoor use.
The system must only be operated in connection with a compatible inverter. The list (BYD Battery-Box Premium HVS & HVM Compatible Inverter List) of these inverters could be read at our websites.
The system is not suitable for supplying life-sustaining medical devices. Please ensure that no personal injury would lead due to the power outage of the system.
Alterations to the BYD system, e.g., changes or modifications are not allowed unless the written permission of BYD is achieved.
Please download Be Connect 2.0 from Google Play or App Store to accomplish the commissioning of the system.
The enclosed document is an integral part of this system. Keep the documentation in a convenient, dry place for future reference and observe all instructions contained therein.
The type label should always be attached to the system.

IMPORTANT SAFETY INSTRUCTIONS

The system has been designed and tested under international safety requirements. However, to prevent personal injury and property damage and ensure long-term operation of the system, please do read this section carefully and observe all safety information at all times.

Battery module leakage
If the battery modules leak electrolytes, contact with the leaking liquid or gas should be avoided. The electrolyte is corrosive, and the contact may cause skin irritation and chemical burns. If one is exposed to the leaked substance, do these actions:

• Inhalation: Evacuate the contaminated area and seek medical help immediately.
• Eye contact: Rinse eyes with flowing water for 15 minutes and seek medical help immediately.
• Skin contact: Wash the affected area thoroughly with soap and water and seek medical help immediately.
• Ingestion: Induce vomiting and seek medical help immediately.

Firefighting measures
The battery modules may catch fire when it is put into the fire. In case of a fire, please make sure that an ABC or carbon dioxide extinguisher is nearby. Water cannot be used to extinguish the fire.
Full protective clothing and self-contained breathing apparatus are required for the firefighters to extinguish the fire.

Battery modules handling and storage guide

• The battery modules and its components should be protected from damage when transporting and handling.
• The weight of the system may cause injury risk. Please take the weight of the system into account while the system is transported and lifted carefully.
• Do not impact, pull, drag, or step on the battery modules.
• Do not insert unrelated objects into any part of the battery modules.
• Do not throw the battery module into a fire.
• Do not soak the battery modules in water or seawater.
• Do not expose to strong oxidizers.
• Do not short circuit the battery modules.
• The battery modules cannot be stored directly under the sun.
• The battery modules cannot be stored in a high humidity environment.
• Use the battery modules only as directed.
• Do not use the battery modules if it is defective, or appears cracked, broken or otherwise damaged, or fails to operate.
• Do not attempt to open, disassemble, repair, tamper with, or modify the battery modules. The battery modules are not user-serviceable.
• Do not use cleaning solvents to clean the battery modules.
• The battery module should be stored in an environment with a temperature range between -10 °C～+50°C, and charged reg ularly according to the table be low w ith no more than 0.5 C (A C-rate is a measure of the rate at which a battery is discharged relative to its maximum capacity. ) to the SOC of 30% after a long time of storage.

Storage environment

temperature

| Relative humidity of the storage environment| Storage time| SOC
---|---|---|---
Below -10℃| /| Not allowed| /
-10~25℃| 5%~70%| ≤ 12 months| 25%≤SOC≤60%
25~35℃| 5%~70%| ≤ 6 months| 25%≤SOC≤60%
35~50℃| 5%~70%| ≤ 3 months| 25%≤SOC≤60%
Above 50℃| /| Not allowed| /

Warning of electric shock
It is a danger to life due to electric shock when live components or DC cables are touched.
The DC cables connected to the system may be live. Touching live DC cables results in death or serious injury due to electric shock.

• Disconnect the battery from a voltage source and make sure it can not be reconnected before working on the device.
• Do not touch non-insulated parts or cables.
• Do not remove the terminal block with the connected DC conductors from the slot under load.
• Wear suitable personal protective equipment for all work on the system.

Notice of property damage
If the battery system doesn’t start at all, please contact BYD authorized service partner within 48 hours. Otherwise, the battery could be permanently damaged.
When the system is installed, it needs to be able to charge and discharge to avoid a deep discharge condition. After the installation, this needs to be checked once a month. If the battery system is not working normally, please get in contact with your local service partner.
During the storage of the battery system, please mind the maximum storage time.

Surge protection
Over voltages (e. g. in the event of a flash of lightning) can be further conducted into the building and to other connected devices in the same network via the network cables or other data cables if there is no surge protection.
Ensure that the system is integrated into the existing surge protection.

Safety Information of the inverter manufacturer
Please read and observe all safety information of the inverter manufacturer.

Symbols on the Battery System

EU Declaration of Conformity

The battery system described in this document complies with the applicable European directives. The certificate is available in the download area of our websites.

Technical Parameters

HVS & HVM

• Operating Temperature -10 °C to +50 °C
• Battery Cell Technology  Lithium Iron Phosphate (cobalt-free)
• Communication CAN/ RS485
• Enclosure Protection Rating IP55
• Round-trip Efficiency ≥ 96%
• Certification VDE2510-50 / IEC62619 / CEC / CE / UN38.3
• Applications ON Grid / ON Grid + Backup / OFF Grid
• Warranty [3] 10 Years

1. DC Usable Energy, test conditions: 100% DOD, 0.2C charge & discharge at +25°C. System Usable Energy may vary with different inverter brands.
2. Charge derating will occur between -10°C and +5°C.
3. Refer to BYD Battery-Box Premium Limited Warranty.

Instructions

Scope of Delivery

Additionally Required Installation Material

TOOL

Installation Location

Connection Limitation

installation

Connection Diagram

NOTICE

• Parallel connection is not applicable to SMA Sunny Boy Storage 3.7-6.0. Please check the inverter’s operating manual on how to connect up to three battery systems.
• The length of the power cables to the combiner box should be the same.
• If the BYD combiner box is not used, the parallel connection device should meet the following requirements. (Except for GoodWe ET 15-30kW when it is connected with the battery systems)
  • No less than IP55 for the outdoor use.
  • Maximum operating voltage: 1000V DC.
  • Maximum output current: 40A DC d) Breaking current: 40A DC.
• The total power cable length between each battery tower and the inverter should be less than 20 meters.

NOTICE

• Parallel connection is not applicable to SMA Sunny Boy Storage 3.7-6.0. Please check the inverter’s operating manual on how to connect up to three battery system.
• The length of the power cables to the combiner box should be same.
• If the BYD combiner box is not used, the parallel connection device should meet the following requirements. (Except for GoodWe ET 15-30kW when it is connected with the battery systems)
  • No less than IPS5 for the outdoor use.
  • Maximum operating voltage: 1000V DC.
  • Maximum output current: 40A DC
  • Breaking current: 40A DC
• The total power cable length between each battery tower and the inverter should be less than 20 meters.

Connecting the Grounding Conductor

Communication Cable Connection to Inverter

Connecting the Data Cable for the Internal Communication (Only needed when two or three battery systems are operated in parallel.)

Connecting the Network

DC Connection

Close Up

Commissioning

Configuration

Switch on the Inverter

Off Grid

Operation

Off Grid

Switch off Order

Extension

LED Status

Contact

BYD Global Service|
---|---
Email| bboxservice@byd.com
Telephone| +86 755 89888888-47175
Address| No.3009, BYD Road, Pingshan, Shenzhen, 5118118, P. R. China
Website| www.bydbatterybox.com

Social Media Link

| https://www.facebook.com/BatteryBoxBYD https://twitter.com/BYD_BatteryBox

https://www.linkedin.com/company/byd-battey-box

Europe| EFT-Systems GmbH
Email| service@eft-systems.de

Telephone

| +49 9352 8523999

+44 (0) 2037695998 (UK)

+34 91 060 22 67 (ES)

+39 02 87368364 (1T)

Address| Bruchtannenstraße 28, 63801 Kleinostheim, Germany
Website| www.eft-systems.de
Australia| Alps Power Pty Ltd
Email| service@alpspower.com.au
Telephone| +61 2 8005 6688
Address| 14/47-51 Lorraine St, Peakhurst NSW 2210
Website| www.alpspower.com.au
South Africa| Afriplus Energy Group (Pty) Ltd
Email| support@afriplusenergy.co.za
Telephone| +27 21 140 3594
Address| The Pavilion, Corner Of Dock & Portswood Road, V&A Waterfront, 8001, Cape Town
Website| www.afriplusenergy.co.za
USA| BYD US Service
Email| bboxusservice@byd.com

WIFI name, password and serial number

References

• AfriPlus | AfriPlus Energy Group proudly serves as the official Southern African partner for the renowned Chinese world market leader, BYD
• ALPS POWER PTY LTD – BYD Battery-Box Australia Authorized Partner
• BYD Battery-Box – BYD Battery-Box
• BYD Battery-Box – BYD Battery-Box
• Eft-Systems
• Eft-Systems
• BYD Battery-Box – BYD Battery-Box
• Eft-Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>