twinkly TWWT050SPP-BUK Light Tree Instruction Manual
- June 13, 2024
- Twinkly
Table of Contents
twinkly TWWT050SPP-BUK Light Tree
download the twinkly app and follow the setup process in the app
physical setup
Suitable for doors of 80-110cm wide by 200-240cm high.
- Position the two strap loops around the bottom corners of the door.
- Adjust the straps as needed to the door’s width.
- Pass the top strap over to the other side of the door.
- Fasten the top and bottom straps, adjusting the buckle as needed.
- Connect the controller to the power adapter and plug it into a power source.
- Enjoy your Twinkly light.
Safety instructions
- Read and follow all instructions that are on the product or provided with the product.
- SAVE THESE INSTRUCTIONS.
- This is an electric product — not a toy! To avoid the risk of fire, burns, personal injury, and electric shock it should not be played with or placed where small children can reach it.
- Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
- This article is not suitable for room illumination and it is only for decoration purpose.
- This seasonal use product is not intended for permanent installation or use.
- Do not mount or place near gas or electric heaters, fireplaces, candles, or other similar sources of heat.
- Do not secure the wiring of the product with staples or nails, or place it on sharp hooks or nails.
- Do not let lamps rest on the supply cord or on any wire.
- Unplug the product when leaving the house for prolonged periods.
- Do not use this product for other than its intended use.
- Do not hang ornaments or other objects from the cord, wire, or light string.
- Do not cover the product with cloth, paper, or any material not part of the product when in use.
- Do not limit the flow of air around the product to avoid heat accumulation.
- Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
- Do not use it in countries other than that for which the product was designed.
- Do not use it in places where there is a risk of electric shock.
- Do not connect the chain to the supply while it is in the packing.
- Where breakage or damage to lamps occurs the chain must not be used/energised but disposed of safely.
- The lamps are not replaceable.
- WARNING – RISK OF ELECTRIC SHOCK IF LAMPS ARE BROKEN OR MISSING. DO NOT USE.
Use and care instructions
- Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
- When storing the product, carefully disassemble it to avoid any undue strain or stress on the product conductors, connections, and wires.
- When not in use, store neatly in a cool, dry location protected from sunlight.
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similarly qualified person in order to avoid a hazard.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- Do not modify the device, so as not to invalidate the certification.
- Do not place metallic/conductive objects near the exposed contacts of the product
- Do not allow children to use the product without supervision.
- Do not clean the device when it is connected to power.
WARNING – To reduce the risk of fire and electric shock:
Do not mount or support wires in a manner that can cut or damage wire
insulation.
Class A Disclaimer: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
Compatibility Disclaimer
Wireless performance is dependent on your device’s Bluetooth/WiFI wireless
technology, please refer to your device’s manufacturer. Ledworks SRL will not
be liable for any lost of data or leakages resulting from the use of these
devices.Consult the dealer or an experienced radio/television technician for
help.
WARNING!
Do not connect the light string to the power supply while it is in the
packaging. The connecting cable cannot be repaired or replaced. THE LAMPS ARE
NOT REPLACEABLE. The lighting chain must not be used without all gaskets being
in place. Lighting chains don’t intend for interconnection. Do not connect
this light string electrically to devices from another manufacturer. CAUTION!
Strangulation hazard. Keep out of reach of young children.
The crossed-out wheeled bin symbol indicates that the item should be disposed
of separately from household waste. The item should be handed in for recycling
in accordance with local environmental regulations for waste disposal.
The manufacturer, Ledworks Srl, declares that this device complies with the
(LVD) 2014/35/EU, (RED) 2014/53/EU, (EMC) 2014/30/EU, (RoHS) 2011/65/EU,
(REACH) 1907/2006 directives. The full text of the EU declaration of
conformity is available at the following Internet address:
www.twinkly.com/certifications
System Requirement
The minimum system requirement for mobile phones are iOS 12 and Android 6.
Check the app store for the latest update to ensure the best performance.
Technical Specifications
- Power supply: see label
- IP protection: IP44
Premium grade LED diodes
To ensure high color rendering, Twinkly products only use high-quality LEDs.
Twinkly’s RGB and RGB+W products are produced according to quality principles
and processes that allow us to obtain a high degree of primary color purity.
The minimum excitation purity values of the Blue, Green and Red components are
shown within the table below.
Bluetooth Licensing
The Bluetooth Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by Ledworks SRL is under
license. Other trademakrs and trade names are those of their respective
owners.
Controller
A: BUTTON / PULSANTE
B: LED INDICATOR
- CONTINUOUS GREEN: Direct Wi-Fi mode, connected
- FLASHING GREEN: Direct Wi-Fi mode, no device connected
- CONTINUOUS BLUE: Home Wi-Fi network mode, connected
- FLASHING BLUE: Home Wi-Fi network mode, connection in progress
- FLASHING RED: Home Wi-Fi network mode, unable to connect
- LIGHT BLUE: SETUP MODE (Bluetooth ON)
- YELLOW: Firmware Update in progress
- CONTINUOUS RED: General error
- FLASHING WHITE: Reset procedure in progress
Home Wi-Fi network connection
Twinkly uses Bluetooth for the setup process only. Wi-Fi connection is
required for operation. You can use:
Home Wi-Fi network connection (recommended):
Connect with your home/office WiFi from the list of available networks.
Direct Wi-Fi connection
Wi-Fi connection is required for operation. You can use:
Direct Wi-Fi connection: Select “Twinkly_xxxxxx” WiFi from the list of
available networks. Password: Twinkly2019 (NOTE: the internet on your phone
will not be available in this case)
Reset twinkly
- Unplug Twinkly from the power socket. Press and hold the controller button.
- While holding the button, plug in Twinkly.
- Keep holding the button until all LEDs turn red (or amber for Gold Edition), then release the button.
Mapping
Map the layout of your decoration to unlock the full potential of your Twinkly lights, such as advanced effects, drawing, and many upcoming features.
References
- Twinkly Help Center
- Twinkly - Innovative Smart LED Lighting Solutions for Home and Busines
- Twinkly - Innovative Smart LED Lighting Solutions for Home and Busines
- Manuals and certifications - Twinkly Help Center
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>