COSTWAY C15xiZSULDL Childrens Desk Student Table User Manual

COSTWAY C15xiZSULDL Childrens Desk Student Table

IMPORTANT INFORMATION

CAUTION!

1. For indoor use only.
2. This product should be placed on a flat surface.
3. Please immediately wipe clean the desktop surface if any liquid is splashed on it.
4. Please check screws regularly to ensure there are no loose parts during daily use.
5. Do not tighten all the screws until the desk and chair are assembled properly.
6. Use a damp cloth to clean the desktop surface.

PACKAGE CONTENTS

• B1

• B2x2

• B3

• B4

• B5

• B6

• B7

• BB

• B10

• B11

• B12

• B13x2

PARTS

• ¢>6.5xct>10.3mm A1x8

• M6x20mm A2x12

• Cl>6.5x¢>15.3mm A3x12

• M5x25mm A4x4

• M6x12mm A5x4

• M4x14mm A6x4

• M6x40mm A7x4
  

• M6x15mm A8x2

• A9x1

• M4 A10x1

Chair Assembly Instructions

1. Insert the chair bracket (B1) into the chair feet (B2).
   

2. Insert the washers (A1) and screws (A2) into the bottom holes in order as the picture shows, and then fix them with a wrench (A10).
   

3. Install the chair back tube (B3) into the upper position of the chair bracket and align the hole, then insert the washers (A3) and screws (A2) in order as the picture shows, and then fix them with a wrench.
   

4. Connect the chair back tube (B4) and (B3) with the chair connecting tube (B5), install the chair back tube (B4) on the completed bracket, insert the washers (A3) and screws (A2) in order as the picture shows, and then fix them with a wrench..
   

5. After installing the chair seat (B6) in the direction shown in the picture, tighten it with the screw (A4).
   
   

6. Insert the chair back (B7), and align it with hole A or hole B according to your needs.
   

7. Use knob (A8) to lock the chair back.

8. After assembly, the level can be adjusted by rotating the foot pads.

9. Install the slide rail (B9) into the desktop (B8) in the direction  shown in the picture, and lock it in place with washers (A3) and screws (A5) in order as the picture shows.
   

10. Install the slide rail (B10) into the desktop (B8) in the direction shown in the picture, and lock it in place with washers (A3) and screws (A5) in order as the picture shows.
    

11. After installing the drawer (B11), align the holes and lock it in place with screws (A6).
    
    

12. Insert the desk bracket (B12) into the desk feet (B13).

13. Lock desk feet in place with washers (A1) and screws (A2) in order as the picture shows.

14. Fix the completed desktop on the desk bracket, and lock it in place with washers (A3) and screws (A7) in order as the picture shows.
    

15. After pressing the hook (A9), it can be inserted into the hole on the side of the desk.

16. After assembly, the level can be adjusted by rotating the foot pads.
    

17. The desktop angle can be adjusted within the range of 0-40°. Loosen the side knob, adjust the desktop to an appropriate angle and then lock it.

Height Adjustment

How to Lift Up
The desk and chair can be adjusted higher by placing one foot on the support bar and pulling the desk or chair up to the required height
How to Lower Down
Gently pull up the desk or chair to the maximum height and then slowly lower down to the minimum height. 12 Lift up again to the required height as above.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>