Waterflex Falcon The Sport Plus Waterbike User Manual
- June 13, 2024
- Waterflex
Table of Contents
Waterflex Falcon The Sport Plus Waterbike User Manual
Safety Precautions
For your safety, please read these instructions before use!
Assembly this product properly using original parts according to the installation instruction. Before assembly, inspect whether packages are in good condition and whether spare parts are complete in accordance with transport precautions and the list of spare parts.
Prior to exercise, make sure equipment fasteners are in locking state.
Please place the exercise bike on a dry and lat ground.
Before starting any exercise, it is essential to consult your doctor. An excessive training or incorrectly executed may cause health issues.
For sustainable use of your bike, please follow these instructions:
- Regularly check the pH of your pool water. It must be between 6.7 and 7.6.
- In case of water shock treatment, please get out the bike from water.
- Avoid placing the bike too close of run-back nozzle.
- Get out the bike from water after each use and rinse with clear water
Please use the attached or other appropriate tools to assemble or repair the exercise bike.
Make necessary maintenance using original spare parts.
For your comfort and safety, adjust the bike pool according to your body.
This exercise bike is only for use by one person at one time.
Use this bike only for the purpose for which it was intended, that is sports practice exercises.
Children and disabled persons shall use the equipment in the presence of adults or healthy people.
The exercise bike has a maximum load of 150KGS.
Exploded view
Tools
Note: use these tools only to assemble this exercise bike
WARNING: Keep the tools away from babies and children.
Installation
Step 1:
Install 17 to the front tube with 16, 18 and 19.
Step 2:
Install the front foot tube (2) onto the main frame (1), then adjust
it with knob (14)
Step 3:
Install the back foot tube (3) onto the main frame (1), then adjust it
with knob (14).
Step 4:
Install handlebar tube (4) onto the main frame (1), then adjust his
position with the «Click-and-turn»
handle.
Step 5:
Install seat tube (5) onto the main frame (1), then adjust his
position with the «Click-and-turn» handle.
Step 6:
Install the handlebar (6) onto its support (4) then ix it with the
«Click-and-turn» handle (15).
Step 7:
Install the saddle (7) onto its support (5) then ix it with the
«Click-and-turn» handle (15).
Step 8:
Lock the pedals (8/9) on the cranks (10/11) with the locknuts (12/13).
Height adjustment knob:
To modify the height of your aquabike, pull the round adjustment knob to
unlock (see on your right). Then adjust the length and let the adjustment knob
come back in position and screw it irmly.
Maintenance advices
This aquabike is made of marine quality AISI 316L stainless steel conforming to standard 2001/95/EC on the general safety of products. Its anti-corrosion treatment makes it suitable for chlorinated water, seawater and thermal waters. It does not require any special care in pH-controlled water (6.7 / 7.6)
- Remove the bike after every use and rinse it with soft water.
- Regularly check the pH of your swimming pool ( pH 7.2 advisable )
- Remove the bike during manual dosages of chemical products or impact treatments. Keep the bike away to avoid any splashes that can stain or any deposits (due to the concentration of chemical products).
- Deposits of powder, salt, corrosive products that encourage the corrosion process.
- When first cleaning the surfaces of the swimming pool (before filling it) as well as subsequent maintenance cleaning, it is advised that you remove the bike from the pool so as to avoid any risk of stains or deposits.
- When you are not using the bike, it must be rinsed thoroughly with soft water, then dried and stored in a location away from chemical products, as well as equipment used for dosing chemical products for pool maintenance.
- lime-scale deposits or stains, these can be removed with a polishing cleaner for stainless steel and a nonabrasive soft cloth. Then wash with clean water and dry it completely.
- We advice you to move your bike once a week for prevent the bottom of the equipment from damage such as abrasion and stain.
Training advices
Exercises instructions
-
The Warm Up Phase
This stage helps get the blood lowing around the body and the muscles working properly. It will also reduce the risk of cramp and muscle injury. It is advisable to do a few stretching exercises as shown below. Each stretch should be held for approximately 30 seconds, do not force or jerk your muscles into a stretch – if it hurts, STOP. -
The Cool Down Phase
This stage is to let your Cardio-vascular System and muscles wind down. This is a repeat of the warm up exercise e.g. reduce your tempo. The stretching exercises should now be repeated, again remembering not to force or jerk your muscles into the stretch.
As you get trained you may need to train longer and harder. It is advisable to train at least three times a week, and if possible space your workouts evenly throughout the week.
Warranty
Your Waterflex product is guaranteed against any manufacturing defect; 3 years
for the metallic frame; 6 months for the wear and tear parts in accordance
with the terms below. This warranty runs from the date of the invoice. Any
faulty part arising from a manufacturing defect duly noted by our technical
services will be replaced or repaired free of charge.
The warranty is rendered null and void in the event of a repair carried out to
the equipment by a person not approved by Waterflex. Faulty parts must be
returned to Waterflex within the warranty period in order to be covered. The
warranty does not cover labor, the cost of unauthorized replacement, or the
cost of transporting the parts in question.
Are considered wearing parts: pedals (foam protection and straps), silicone feet, handles «click and turn», adjustment knob, protection plugs.
The following are expressly excluded from the warranty:
- Malfunction or damage arising from the use of unauthorized accessories.
- Damage resulting from the installation or a repair which does not comply with the safety instructions.
- Malfunction or damage resulting from the improper chemical environment in the pool.
- Defects resulting from accidents, incorrect or unreasonable use (impact, contact with chemical products, inappropriate handling), alteration as well as the consequences of the normal wear and tear of the product.
The shipping box must be kept in perfect condition throughout the duration of
the warranty.
The warranty becomes void if failure to comply with this clause.
Symbols
Distribution POOLSTAR FRANCE
www.poolstar.fr
ZA les Pielettes – 13740 LE ROVE – FRANCE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>