BOSCH HCB50651UC 30 inch Wall Mount Range Hood User Manual
- June 13, 2024
- Bosch
Table of Contents
- Hood
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Hood
Use and Care Manual
HCB50651UC, HCB56651UC
Additional information on products, accessories, replacement parts and services can be found at www.bosch-home.com and in the online shop.
Safety Definitions
WARNING
This indicates that death or serious injuries may occur as a result of non- observance of this warning.
CAUTION
This indicates that minor or moderate injuries may occur as a result of non- observance of this warning.
NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.
Note: This alerts you to important information and/or tips.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WARNING
When properly cared for, your new appliance has been designed to be safe and reliable. Read all instructions carefully before use. These precautions will reduce the risk of burns, electric shock, fire, and injury to persons. When using kitchen appliances, basic safety precautions must be followed, including those in the following pages.
General notes
Examine the appliance after unpacking it. In the event of transport damage, do not plug it in.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
-
Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
-
Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. -
-
-
-
WARNING
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
-
Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
-
Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
-
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
-
Ducted fans must always be vented to the outdoors.
-
-
This appliance is not intended for operation with an external clock timer or a
remote control.
Have an appropriate fire extinguisher available, nearby, highly visible and
easily accessible near the appliance.
Fire Safety
WARNING
To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages.
WARNING
To reduce the risk of fire, use only metal ductwork.
Always have a working smoke detector near the kitchen.
WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
b. Always turn hood ON when cooking at high heat.
c. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriate for the size of
the surface element.
Do not flambé under the extractor hood or work with a naked flame. When switched on, the extractor hood draws flames into the filter. There is a risk of fire due to deposits on the grease filter!
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
In the event that personal clothing or hair catches fire, drop and roll
immediately to extinguish flames.
Smother flames from food fires other than grease fires with baking soda. Never
use water on cooking fires.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:
-
SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
-
NEVER PICK UP A FLAMING PAN – You may be burned.
-
DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
-
Use an extinguisher ONLY if:
– You know you have a Class ABC extinguisher, and you already know how to operate it.
– The fire is small and contained in the area where it started.
– The fire department is being called
– You can fight the fire with your back to an exit. -
-
Whenever possible, do not operate the ventilation system during a cooktop fire. However, do not reach through fire to turn it off.
WARNING
RISK OF FIRE
When gas burners are in operation without any cookware placed on them, they
can build up a lot of heat. A ventilation appliance installed above the cooker
may become damaged or catch fire. Only operate the gas burners with cookware
on them.
WARNING
RISK OF FIRE
During simultaneous use of multiple gas cooktops, a great deal of heat is
created. A ventilation device located above it can become damaged or catch
fire. Never use two gas cooktops together at maximum heat for longer than 15
minutes. One large burner with over 17,000 Btu/hr (5 kW) (wok) is equal to the
wattage of two gas burners.
WARNING
RISK OF FIRE
Hot oil and fat catch fire fast. Never leave hot oil and fat unsupervised.
Never extinguish a fire with water. Switch off the cooking position. Suffocate
flames carefully with a lid, a fire blanket or similar.
WARNING
RISK OF FIRE
Grease deposits in the grease filter can ignite.
Clean the grease filter at least every two months.
Never operate the appliance without the grease filter.
WARNING
RISK OF FIRE
Grease deposits in the grease filter can catch fire. Never work with a naked
flame near the appliance (e.g. flambéing). Install the unit near a heat-
producing appliance for solid fuels (e.g. wood or coal) only if there is a
closed, non-detachable cover. There must be no flying sparks.
Burn Prevention
WARNING
RISK OF BURNS
The accessible parts get hot during operation. Never touch hot parts. Keep
children away.
Child Safety
When children become old enough to use the appliance, it is the responsibility
of the parents or legal guardians to ensure that they are instructed in safe
practices by qualified persons.
Remove all tape and packaging before using the appliance. Destroy the
packaging after unpacking the appliance. Never allow children to play with
packaging material.
Do not allow anyone to climb, stand, lean, sit, or hang on any part of an
appliance, especially a door, warming drawer, or storage drawer. This can
damage the appliance, and the unit may tip over, potentially causing severe
injury.
Do not allow children to use this appliance unless closely supervised by an
adult. Children and pets should not be left alone or unattended in the area
where the appliance is in use. They should never be allowed to play in its
vicinity, whether or not the appliance is in use.
CAUTION
Items of interest to children should not be stored in an appliance, in cabinets above an appliance or on the backsplash. Children climbing on an appliance to reach items could be seriously injured.
Cleaning Safety
WARNING
Be sure the entire appliance (including the grease filters and light bulbs, if applicable) has cooled and grease has solified before attempting to clean any part of the appliance.
Do not use steam cleaners to clean the appliance.
Safe use
WARNING
Do not repair, replace or remove any part of the appliance unless specifically recommended in the manuals. Improper installation, service or maintenance can cause injury or property damage. Refer to this manual for guidance. All other servicing should be done by a qualified technician.
WARNING
RISK OF INJURY
Items placed on the appliance may fall down. Do not place any objects on the
appliance.
Proper Installation and Maintenance
Have the installer show you the location of the circuit breaker or fuse. Mark
it for easy reference.
This appliance must be properly installed and grounded by a qualified
technician. Connect only to properly grounded outlet. Refer to Installation
Instructions for details.
This appliance is intended for normal family household use only. It is not
approved for outdoor use. See the Warranty. If you have any questions, contact
the manufacturer.
Do not store or use corrosive chemicals, vapors, flammables or nonfood
products in or near this appliance. It is specifically designed for use when
heating or cooking food. The use of corrosive chemicals in heating or cleaning
will damage the appliance and could result in injury.
Do not operate this appliance if it is not working properly, or if it has been
damaged. Contact an authorized servicer.
Do not repair or replace any part of the appliance unless specifically
recommended in this manual. Refer all servicing to a factory authorized
service center.
CAUTION
Grease left on filters can remelt and move into the vent.
CAUTION
Turn power off at breaker before removing a damaged bulb. Do not touch the bulbs immediately after use. The bulbs will remain hot for several minutes.
WARNING
Make sure the appliance and lights are cool and power to the appliance has been turned off before replacing the light bulb(s). Failure to do so could result in electrical shock or burns.The lenses (if equipped) must be in place when using the appliance.The lenses (if equipped) serve to protect the light bulb from breaking.The lenses (if equipped) are made of glass. Handle carefully to avoid breaking. Broken glass can cause an injury.
Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.
WARNING
When the hood is operated in exhaust-air mode simultaneously with a different
burner which also makes use of the same chimney (such as gas, oil or coal-
fired heaters, continuous-flow heaters, hot-water boilers) care must be taken
to ensure that there is an adequate supply of fresh air which will be needed
by the burner for combustion.
Safe operation is possible provided that the under pressure in the room where
the burner is installed does not exceed 4 Pa (0.04 mbar).
This can be achieved if combustion air can flow through non-lockable openings,
e.g. in doors, windows and via the air-intake/exhaust-air wall box or by other
technical measures, such as reciprocal interlocking, etc.
WARNING
Avoid carbon monoxide poisoning – Provide adequate air intake so combustion
gases are not drawn back into the room.
An air-intake/exhaust-air wall box by itself is no guarantee that the limiting
value will not be exceeded.
Note: When assessing the overall requirement, the combined ventilation system for the entire household must be taken into consideration. This rule does not apply to the use of cooking appliances, such as cooktops and ovens.
Proposition 65 Warnings
This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California:
STATE OF CALIFORNIA PROPOSITION 65 WARNING:
WARNING
Cancer and reproductive harm –
www.P65Warnings.ca.gov.
Causes for damages
CAUTION
Risk of damage due to corrosion. Always turn appliance on when cooking to avoid condensation buildup. Condensation can lead to corrosion damages.
Always replace defective bulbs immediately to avoid an overload of the remaining bulbs.
Risk of damage due to ingress of humidity into the electronic circuitry. Never
clean operator controls with a wet cloth.
Surface damage due to incorrect cleaning. Clean stainless steel surfaces in
the grind direction only. Do not use any stainless steel cleaners for operator
controls.
Surface damage due to strong or abrasive cleaning agents. Never use strong and
abrasive cleaning agents.
Risk of damage from condensation back flow. Install exhaust vent at a slight
downward slope away from the appliance (1° slope).
Protecting the environment
Unpack the appliance and dispose of the packaging in line with environmental requirements.
Operating modes
You can use this appliance in the air extraction or the recirculation mode.
Exhaust air mode
The air that is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.
Note: Ventilation may not exit through an already operational smoke or exhaust chimney, nor a duct used for ventilating furnace installation areas.
- If the ventilation is intended to pass through a smoke or exhaust that is not in operation, the responsible area heating inspector must give approval.
- If the ventilation passes through an external wall, use a telescope wall sleeve.
Circulating-air mode
The air that is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.
Note: To bind odors in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are available from specialist retailers, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use.
Operating the appliance
These instructions apply to several appliance models. It is possible that individual features are described that do not apply to your appliance.
Note: Turn the extractor hood on when you start cooking and switch it off again a few minutes after you have finished cooking. This is the most effective way to eliminate cooking vapor.
Control panel
Explanation
1 Turn the fan down
2 Turn the fan up
3 Display panel
4 Switch on lighting
5 Timer
Turn on the fan
Note: Always adjust the fan strength to meet current conditions. If there is a large build-up of steam or fumes, select a high fan setting.
Switching on
-
Press “+” button.
The current ventilator settings are indicated by a bar on the display panel. -
Press “+” or “-” keys to change the ventilator settings.
Switching off
- Press the “-” button repeatedly until the ventilator switches off.
Lighting
The lighting can be switched on and off independently of the ventilation.
1. Press the “Light” button.
The lighting switches on.
2. Press the “Light” button again.
The brightness increases.
3. Press the “Light” button a third time.
The lighting switches off.
Saturation notification
The saturation of the metal grease filter (after 30 hours of ventilation operation) or of the activated carbon filter (after 120 hours of ventilation operation) is indicated on the display panel:
- Metal grease filter: “clean grease filter” appears on the display panel.
- Activated carbon filter: “replace charcoal filter” appears on the display panel.
If you have not yet done so, the metal mesh grease filters should be cleaned
or the activated carbon filter changed now.
For instructions on how to clean the metal grease filters, please refer to the
Cleaning and maintenance section.
Resetting the saturation displays
- Metal grease filter: Press and hold the “+” button for 5 seconds.
- Activated carbon filter: Press and hold the “-” button for 5 seconds.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display must be switched
over accordingly:
- The extractor hood must be connected and switched off.
- Press the “+” and “-” keys simultaneously until “Able” lights up briefly on the display panel.
- Repeatedly press the button combination to switch the electronic control display back to exhaust air mode. “None” appears on the display panel.
Timer
The timer has no influence on the functions of the exhaust hood. The duration of the timer can be set to between 1 minute and 60 minutes. The default setting is 10 minutes.
1. Press the “Timer” button.
10 flashes on the display panel.
2. Set the required duration with the “+” and “-” buttons.
After 5 seconds, the time that has been set is adopted.
An audible signal sounds once the time has elapsed and “End” appears on the
display panel for 3 seconds.
Note: To switch off the timer earlier, press any button.
Fan back flow
The run-on time is ten minutes and cannot be changed.
1. Select ventilator setting.
2. Press “Timer” button for 3 seconds.
Once this time has elapsed, the ventilation and lighting switch off
automatically. The display shows the message “End.”
The ventilator run-on can be interrupted at any time by pressing one of the
buttons.
Audible signal
Switching on audible signal
- Press and hold the “Light” button for 5 seconds.
- An audible signal sounds and “Snd” appears on the display panel for 3 seconds.
Switching off audible signal
- Press and hold the “Light” button for 5 seconds.
- “Snd” appears on the display panel for 3 seconds.
Overheating protection
The appliance is equipped with overheating protection. If high temperatures are measured on the appliance, the appliance switches automatically to the highest ventilator setting until the temperature drops again.
-
If the hood is switched on, the highest ventilator setting is set. If the temperature drops again, the appliance switches back to the previously-selected ventilator setting.
-
If the hood is switched off, the appliance switches automatically to the highest ventilator setting. If the temperature drops again, the appliance switches off automatically.
-
While the overheating protection is active, “Auto” appears on the display panel. The ventilator setting cannot be reduced in this time.
-
-
Cleaning and maintenance
WARNING
WARNING
To avoid risk of fire and explosion do not use flammable liquids or solvents.
Always unplug or disconnect the appliance from the power supply before
servicing.
Do not use steam cleaners to clean the appliance.
Hidden surfaces may have sharp edges. Use caution when reaching behind or
under appliance.
WARNING
RISK OF BURNS
The appliance will become hot when in use, especially in the area surrounding
the bulbs. Let cool before cleaning.
WARNING
RISK OF ELECTRIC SHOCK
Penetrating damp can cause electric shock. Only clean appliance with a damp
cloth. Prior to cleaning, pull the plug or flip the breaker in the fusebox.
Cleaning agents
To prevent various surfaces from becoming damaged due to incorrect cleaning agents, follow the specifications given in the table. Do not use
- cleaning agents that are harsh or scouring,
- cleaning agents with high alcohol content,
- hard scouring pads or sponges,
- high-pressure cleaners or steam cleaners.
Thoroughly rinse all new sponges before use.
Observe all instructions and warnings accompanying cleaning agents.
Area | Cleaning agents |
---|---|
Stainless steel | Warm soapy water: |
Clean with a dish rag and dry with a soft towel.
Only clean stainless steel with the grain.
Specific products for stainless steel care are available from customer service
or from specialized retailers. Apply a thin layer of the care product with a
soft cloth.
Varnished surfaces| Warm soapy water:
Clean with a damp dish rag and dry with a soft towel.
Do not use stainless steel cleaner.
Aluminum and plastic| Glass cleaner:
Clean with a soft cloth.
Glass| Glass cleaner:
Clean with a soft cloth. Do not use a glass scraper.
Controls| Warm soapy water:
Clean with a damp dish rag and dry with a soft towel.
Risk of damage to electronics due to permeating damp. Never clean controls
with a wet cloth.
Do not use stainless steel cleaner.
Cleaning the metal grease filter
These instructions apply to several appliance models. It is possible that individual features are described that do not apply to your appliance.
WARNING
RISK OF FIRE
Grease deposits in the grease filter can ignite.
Clean the grease filter at least every two months.
Never operate the appliance without the grease filter.
Notes
- Do not use any aggressive, acidic or alkaline cleaning agents.
- When cleaning the metal grease filters, also clean the metal grease filter holder in the appliance with a moist cloth.
- You can clean the metal grease filters in a dishwasher or by hand.
By hand:
Note: You can use a special grease solvent if soiling is stubborn. You can order it via the online shop.
- Soak the metal grease filters in hot soapy solution.
- Use a brush for cleaning and then rinse the filters well.
- Allow the metal grease filters to drip dry.
In the dishwasher:
Note: Slight discoloration is possible when cleaning the grease filters in the dishwasher. This does not affect the metal grease filter’s functioning.
- Do not clean extremely dirty metal grease filters with dishes.
- Loosely position the metal grease filter in the dishwasher. The metal grease filters must not be jammed in.
Uninstalling metal grease filter
1. Open the latch and fold down the metal grease filter. Simultaneously
use your other hand to grasp under the metal grease filter.
2. Remove the metal grease filter from its mounting.
Notes
- Grease can gather in the bottom of the metal grease filter.
- Hold metal grease filter horizontally to prevent grease from dripping.
3. Clean metal grease filter.
Installing metal grease filter
1. Insert metal grease filter.
Simultaneously use your other hand to grasp under the metal grease filter.
2. Flip metal grease filter up and snap the latch into place.
Troubleshooting
You can often easily eliminate problems that may occur on your own. Before calling customer service, take into account the following information.
WARNING
RISK OF ELECTRIC SHOCK
Improper repairs are dangerous. Only an after-sales technician trained by us
may perform repairs and may replace damaged connecting leads. Remove the mains
plug or deactivate the fuse in the fuse box if the appliance is defective.
Call after-sales service.
Disruption | Possible cause | Solution |
---|---|---|
Appliance is not working | Power outage | Check whether other kitchen appliances |
are working
Fuse defective| Check in the fuse box whether the fuse for the appliance is in
working order
Lighting not working.| Bulbs defective.| Replace bulbs, see chapter “Replace
Bulbs.”
Changing bulbs
WARNING
RISK OF ELECTRIC SHOCK
When changing the bulbs, the bulb socket contacts are live. Before replacing
the bulb, unplug the appliance or switch off the circuit breaker in the fuse
box.
Important! Use only bulbs of the same type and the same power (see also lamp socket or rating plate).
Replacing halogen bulbs
Note: When inserting halogen bulbs, do not touch the glass bulb. Use a clean cloth to insert the halogen bulbs.
1. Let the lamps cool down.
2. Carefully remove bulb ring using a suitable tool.
3. Pull out the bulb and replace with a bulb of the same type.
4. Insert lamp cover.
5. Insert appliance plug or switch on fuse again.
Replace the bulb with one of the same type:
Voltage (V): 120 V
40 w max. power:
G9 socket:
Customer service
Our customer service department is there for you if your appliance requires
repair. We’ll always find a suitable solution, also to avoid unnecessary
technician visits.
When calling, please give the Product Number (P-No.) and the Serial Number
(S-No.) so that we can offer you the most competent service. The
identification plate listing the numbers can be found inside of the appliance
(remove metal grease filter to find it).
So that you don’t have to search for them when you need them, you can enter
your appliance information and the customer service number here.
P-No. S-No.
Customer service
Please note that a visit from a customer service technician in the event of
incorrect operation is not free of charge, even during the warranty period.
Please find the contact data of all countries in the enclosed customer service
list.
To book an engineer visit and product advice
US 800 944 2904
toll-free
You can rely on the manufacturer’s expertise. Rest assured that the repair will be handled by trained service technicians who have the original replacement parts for your appliance.
Accessories
(not included in the delivery)
Accessories Material number
Recirculation module HCREC5UC
Charcoal filter HCIFILTUC
Flue duct HCBEXT5UC
STATEMENT OF LIMITED PRODUCT WARRANTY
What this Warranty Covers & Who it Applies to
The limited warranty provided by BSH Home Appliances (“Bosch”) in this Statement of Limited Product Warranty applies only to the Bosch appliance sold to you (“Product”), provided that the Product was purchased:
- For your normal, household (non-commercial) use, and has in fact at all times only been used for normal household purposes.
- New at retail from a BSH authorized dealer or directly from BSH (not a display, “as is”, or previously returned model), and not for resale, or commercial use.
- Within the United States or Canada, and has at all times remained within the country of original purchase.
The warranties stated herein apply to the original purchaser of the product warranted herein and to each succeeding owner of the product purchased for ordinary home use during the term of the warranty.
Please make sure to register your Product; while not necessary to effectuate warranty coverage, it is the best way for Bosch to notify you in the unlikely event of a safety notice or product recall.
How Long the Warranty Lasts
Bosch warrants that the Product is free from defects in materials and workmanship for a period of three hundred and sixty-five (365) days from the date of the original delivery. The foregoing timeline begins to run upon the date of the original delivery, and shall not be stalled, tolled, extended, or suspended, for any reason whatsoever. This Product is also warranted to be free from cosmetic defects in material and workmanship (such as scratches of stainless steel, paint/porcelain blemishes, chips, dents, or other damage to the finish) of the Product, for a period of thirty (30) days from the date of delivery or closing date for new construction. This cosmetic warranty excludes slight color variations due to inherent differences in painted and porcelain parts, as well as differences caused by kitchen lighting, product location, or other similar factors. This cosmetic warranty specifically excludes any display, floor, “As Is”, or “B” stock appliances.
Repair/Replace as Your Exclusive Remedy
During this warranty period, Bosch or one of its authorized service providers will repair your Product without charge to you (subject to certain limitations stated herein) if your Product proves to have been manufactured with a defect in materials or workmanship. If reasonable attempts to repair the Product have been made without success, then Bosch will replace your Product (upgraded models may be available to you, in Bosch’s sole discretion, for an additional charge). Nothing in this warranty requires damaged or defective parts to be replaced with parts of a different type or design than the original part. All removed parts and components shall become the property of Bosch at its sole option. All replaced and/or repaired parts shall assume the identity of the original part for purposes of this warranty and this warranty shall not be extended with respect to such parts. Bosch’s sole liability and responsibility hereunder is to repair manufacturer defective Product only, using a Bosch authorized service provider during normal business hours. For safety and property damage concerns, Bosch highly recommends that you do not attempt to repair the Product yourself, or use a non-authorized service provider; Bosch will have no responsibility or liability for damage resulting from repairs or work performed by a non-authorized service provider. Authorized service providers are those persons or companies that have been specially trained on Bosch products, and who possess, in Bosch’s opinion, a superior reputation for customer service and technical ability (note that they are independent entities and are not agents, partners, affiliates or representatives of Bosch). Nevertheless, taking your product to be serviced by a repair shop that is not affiliated with or an authorized dealer of Bosch will not void this warranty. Also, using third-party parts will not void this warranty. Notwithstanding the foregoing, Bosch will not incur any liability, or have responsibility, for the Product if it is located in a remote area (more than 100 miles from an authorized service provider) or is reasonably inaccessible, hazardous, threatening, or treacherous locale, surroundings, or environment; in any such event, if you request, Bosch would still pay for labor and parts and ship the parts to the nearest authorized service provider, but you would still be fully liable and responsible for any travel time or other special charges by the service company, assuming they agree to make the service call. Further, to the extent you have installed the Product in a difficult-to-access location or have otherwise installed temporary or permanent fixtures that create barriers to accessing or removing the Product, Bosch will not incur any liability for, or have responsibility, for work or costs associated with moving the Product or otherwise creating access to the Product in order to repair or replace it. All such costs shall be your sole responsibility.
Out of Warranty Product
Bosch is under no obligation, at law or otherwise, to provide you with any concessions, including repairs, prorates, or Product replacement, once this warranty has expired.
Warranty Exclusions
The warranty coverage described herein excludes all defects or damage that is not the direct fault of Bosch, including without limitation, one or more of the following:
- Use of the Product in anything other than its normal, customary and intended manner (including without limitation, any form of commercial use, use or storage of an indoor product outdoors, use of the Product in conjunction with air or water-going vessels).
- Any party’s willful misconduct, negligence, misuse, abuse, accidents, neglect, improper operation, failure to maintain, improper or negligent installation, tampering, failure to follow operating instructions, mishandling, unauthorized service (including self performed “fixing” or exploration of the appliance’s internal workings).
- Adjustment, alteration or modification of any kind.
- A failure to comply with any applicable state, local, city, or county electrical, plumbing and/or building codes, regulations, or laws, including failure to install the product in strict conformity with local fire and building codes and regulations.
- Ordinary wear and tear, spills of food, liquid, grease accumulations, or other substances that accumulate on, in, or around the Product.
- Any external, elemental and/or environmental forces and factors, including without limitation, rain, wind, sand, floods, fires, mud slides, freezing temperatures, excessive moisture or extended exposure to humidity, lightning, power surges, structural failures surrounding the appliance, and acts of God.
- Service calls to correct the installation of your Product, to instruct you how to use your Product, to replace house fuses or correct house wiring or plumbing.
- Removal and replacement of trim or decorative panels that interfere with servicing the Product.
- Damage or defects caused by labor or parts installed by any non-authorized service provider, unless approved by Bosch before service is performed.
In no event shall Bosch have any liability or responsibility whatsoever for damage to surrounding property, including cabinetry, floors, ceilings, and other structures or objects around the Product. Also excluded from this warranty are Products, on which the serial numbers have been altered, defaced, or removed; service visits to teach you how to use the Product, or visits where there is nothing wrong with the Product; correction of installation problems (you are solely responsible for any structure and setting for the Product, including all electrical, plumbing or other connecting facilities, for proper foundation/flooring, and for any alterations including without limitation cabinetry, walls, floors, shelving, etc.); and resetting of breakers or fuses.
TO THE EXTENT ALLOWED BY LAW, THIS WARRANTY SETS OUT YOUR EXCLUSIVE REMEDIES WITH RESPECT TO PRODUCT, WHETHER THE CLAIM ARISES IN CONTRACT OR TORT (INCLUDING STRICT LIABILITY, OR NEGLIGENCE) OR OTHERWISE. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED. ANY WARRANTY IMPLIED BY LAW, WHETHER FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, SHALL BE EFFECTIVE ONLY FOR THE PERIOD THAT THIS EXPRESS LIMITED WARRANTY IS EFFECTIVE. IN NO EVENT WILL THE MANUFACTURER BE LIABLE FOR CONSEQUENTIAL, SPECIAL, INCIDENTAL, INDIRECT, “BUSINESS LOSS”, AND/OR PUNITIVE DAMAGES, LOSSES, OR EXPENSES, INCLUDING WITHOUT LIMITATION TIME AWAY FROM WORK, HOTELS AND/ OR RESTAURANT MEALS, REMODELLING EXPENSES IN EXCESS OF DIRECT DAMAGES WHICH ARE DEFINITIVELY CAUSED EXCLUSIVELY BY BOSCH, OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, AND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
No attempt to alter, modify or amend this warranty shall be effective unless authorized in writing by an officer of BSH.
Obtaining Warranty Service
To obtain warranty service for your product, you should contact Bosch Customer Service at 1-800-944-2904 to schedule a repair.
Product information
For handy reference, copy the information below from the rating plate. Keep your invoice and/or delivery documents for warranty validation.
Model number (E-Nr.)
Production number (FD)
Date of delivery
9001126907 01/23
LI32DB
1901 Main Street, Suite 600 • Irvine, CA 92614 •
800-944-2904
www.bosch-home.com • © 2023 BSH Home Appliances
030130
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>