YOLINK YS7804-EC Motion Sensor User Guide
- June 13, 2024
- YOLINK
Table of Contents
Motion Sensor
YS7804-UC, YS7804-EC
Quick Start Guide
Welcome!
Thank you for purchasing YoLink products! We appreciate you trusting YoLink
for your smart home & automation needs. Your 100% satisfaction is our goal. If
you experience any problems with your installation, with our products or if
you have any questions that this manual does not answer, please contact us
right away. See the Contact Us section for more info.
Thank you!
Eric Vanzo
Customer Experience Manager
The following icons are used in this guide to convey specific types of
information:
Very important information (can save you time!)
Good to know info but may not apply to you
Before You Begin
Please note: this is a quick start guide, intended to get you started on the installation of your Motion Sensor. Download the full Installation & User Guide by scanning this QR code:
Installation & User Guide
https://www.yosmart.com/support/YS7804-UC/docs/instruction
You can also find all guides and additional resources, such as videos and troubleshooting instructions, on the Motion Sensor Product Support Page by scanning the QR code below or by visiting: https://shop.yosmart.com/pages /motion-sensor-product-support
Product
Support
https://shop.yosmart.com/pages/motion-sensor-product-support
Your Motion Sensor connects to the internet via a YoLink hub (SpeakerHub or
the original YoLink Hub), and it does not connect directly to your WiFi or
local network. In order for remote access to the device from the app, and for
full functionality, a hub is required.
This guide assumes the YoLink app has been installed on your smartphone, and a
YoLink hub is installed and online (or your location, apartment, condo,
etcetera, is already served by a YoLink wireless network).
In the Kit
|
---|---
Motion Sensor| 2 x AAA Batteries
(Pre-Installed)
| 
Quick Start Guide| Mounting Plate
Required Items
The following items may be required:
| 
---|---
Double-Sided Mounting Tape| Rubbing Alcohol Pads
Get to Know Your Motion Sensor
LED Behaviors
| Blinking Red Once, then Green Once
Device Start Up
---|---
| Blinking Red And Green Alternately
Restoring to Factory Default Settings
| Blinking Green
Connecting to the Cloud
| Fast Blinking Green
Control-D2D Pairing in Progress
| Slow Blinking Green
Updating
| Blinking Red Once
Device is Connected to the Cloud and is Functioning Normally
| Fast Blinking Red
Control-D2D Unpairing in Progress
| Fast Blinking Red Every 30 Seconds
Batteries Are Low; Replace the Batteries
Power Up
Install the App
If you are new to YoLink, please install the app on your phone or tablet, if
you have not already. Otherwise, please proceed to the next section.
Scan the appropriate QR code below or find the “YoLink app” on the appropriate
app store.
|
---|---
http://apple.co/2Ltturu
Apple phone/tablet
iOS 9.0 or higher| http://bit.ly/3bk29mv
Android phone or
tablet 4.4 or higher
Open the app and tap Sign up for an account. You will be required to provide a
username and a password. Follow the instructions, to set up a new account.
Allow notifications, when prompted.
You will immediately receive a welcome email from no-
reply@yosmart.com with some helpful
information. Please mark the yosmart.com domain as safe, to ensure you receive
important messages in the future.
Log in to the app using your new username and password.
The app opens to the Favorite screen.
This is where your favorite devices and scenes will be shown. You can organize
your devices by room, in the Rooms screen, later.
Add Your Motion Sensor to the App
- Tap Add Device (if shown) or tap the scanner icon:
- Approve access to your phone’s camera, if requested. A viewfinder will be shown on the app.
- Hold the phone over the QR code so that the code appears in the viewfinder. If successful, the Add Device screen will be displayed.
- Follow the instructions to add your Motion Sensor to the app.
Installation
Sensor Location Considerations:
Before installing your Motion Sensor, please consider the following:
- Passive-infrared (PIR) motion sensors such as your YoLink Motion Sensor detect movement within a specific area by sensing the infrared energy emitted from a body, causing a temperature change, as it moves across the sensor’s field of view.
- The Motion Sensor is intended for indoor use. As the sensor uses infrared sensing technology, ambient temperature and the temperature of the detection target (such as people) is a factor. Hot, outdoor environments, even if under cover (such as a car port) will result in undesired behaviors such as false alarms or failure to detect motion. Consider our Outdoor Motion Sensor for outdoor applications.
- Do not use the sensor in extremely hot or steamy environments, such as in a boiler room or near a sauna or hot tub.
- Do not aim your Motion Sensor at, or place the sensor near sources of heat, such as space heaters, or near sources of rapid temperature change, such as heating or cooling grilles or registers.
- Do not aim your Motion Sensor at windows, fireplaces, or other sources of light. For example, at night, lights from a vehicle shining through a window directly into the motion sensor may cause a false alert.
- Mount the Motion Sensor to a rigid surface, free of vibration.
- Placement of the Motion Sensor in high traffic areas will reduce the life of the batteries.
- Pets such as cats and dogs can set off the Motion Sensor. If you have pets and are using the sensor for security applications, consider wall-mounting your sensor, which provides more control over the detection region.
- The Motion Sensor best detects motion moving across its field of view, as opposed to moving directly towards it.
- The Motion Sensor has a 360° cone of coverage (viewed from directly below, sensor facing down), with a 120° coverage profile (viewed from the side of the sensor). Detection range is approximately 20 feet (about 6 meters).
- If mounting your Motion Sensor on the ceiling, the ceiling height should be no more than 13 feet (about 4 meters).
- If wall-mounting your Motion Sensor, the suggested mounting height is approximately 5 feet (about 1.5 meters).
- The Motion Sensor has an integral magnet that allows for mounting to the metal mounting plate or to a metal surface. The metal plate has mounting tape, that allows it to be secured to a suitable surface. Additional mounting plates with pre-installed mounting tape are available for purchase on our website.
- We recommend you test the proposed location of your Motion Sensor before permanently installing it. This can be easily done with painter’s tape, by taping the mounting plate to the proposed location, allowing for testing the sensor, as explained later.
- The YoLink Motion Sensor does not have pet immunity features. One method to prevent false alerts caused by pets includes avoiding the use of this sensor in areas the pets may occupy while the sensor is armed. Wall-mounting your sensor higher on the wall, so that the coverage ‘cone’ does not include the floor of the room, is another method. Adjusting the Motion Sensor’s sensitivity to low may help (but it may slow response time, or prevent operation entirely). Large dogs and/or pets that climb up on furniture will likely cause a false alert, if in the coverage region of your Motion Sensor. A trial & error process of testing the proposed sensor location and settings, with your pet, is recommended.
The mounting tape is extremely adhesive and can be very difficult to remove
later without damage to the surface (removing paint, even drywall). Use care
when installing the mounting plate on delicate surfaces.
Install and test the Motion Sensor:
- If mounting the Motion Sensor to a metal surface, you can do so at this time. Otherwise, you may either secure the mounting plate to the surface, using painter’s tape (to test the location first), or you can secure the mounting plate to the surface. Do so by first cleaning the installation area, using rubbing alcohol or similar to remove all dirt, oil or grease from the mounting surface. Remove the backing from the mounting tape, then place the mounting plate at the desired location, tape side to the mounting surface. Press and hold for at least 5 seconds.
- Place the Motion Sensor on the mounting plate. Ensure it has a good magnetic connection to the plate.
- Next, test the sensor. It is very important that you test the sensor, as realistically as possible, to ensure it works as required for your application. With your phone in-hand, using the app, refer to the Motion Sensor status as you walk through the coverage area. You may need to adjust the location of the sensor and/or sensitivity.
- When the sensor responds as desired, if temporarily installed, you may permanently install it as noted in step 1.
Please note! A motion sensor is not a guarantee of security or protection
against intrusion into your home or business. As noted, motion sensors can be
prone to false alarms under certain conditions, and they may also not respond
as desired under certain conditions. Consider adding additional motion
sensors, as well as door sensors and/or vibration sensors, to enhance your
security system and make it more responsive to intrusion.
Refer to the full Installation & User Guide and/or the online resources for
additional information and to complete the set-up and settings for your Motion
Sensor.
Contact Us
We are here for you, if you ever need any assistance installing, setting up or
using a YoLink app or product!
Need help? For fastest service, please email us 24/7 at
service@yosmart.com
Or call us at 831-292-4831 (US phone
support hours: Monday – Friday, 9AM to 5PM Pacific)
You can also find additional support and ways to contact us at:
www.yosmart.com/support-and-service
Or scan the QR code:
Support Home Page
http://www.yosmart.com/support-and-service
Finally, if you have any feedback or suggestions for us, please email us at
feedback@yosmart.com
Thank you for trusting YoLink!
Eric Vanzo
Customer Experience Manager
15375 Barranca Parkway
Ste. J-107 | Irvine, California 92618
© 2023 YOSMART, INC IRVINE,
CALIFORNIA
Documents / Resources
|
YOLINK YS7804-EC Motion
Sensor
[pdf] User Guide
YS7804-UC, YS7804-EC, YS7804-EC Motion Sensor, Motion Sensor, Sensor
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>