RYOBI RTS1800 Sawing Machine User Manual

June 9, 2024
RYOBI

RYOBI RTS1800 Sawing Machine

TOOLS REQUIRED

INTENDED USE

The table saw is designed to be operated by one person for the purpose of rip and cross cutting wood, up to a maximum depth of 80 mm at 0° bevel angle. At the maximum 45 bevel angle the maximum depth of cut is 55 mm. The table saw is designed and intended to be fixed to a stable surface or a work stand as supplied by the manufacturer. Hard and soft wood plus particle and fibre boards may be cut. Only blade and riving knife combinations supplied by the manufacturer of this table saw, for this table saw may be used.

RESIDUAL RISKS
Even when the table saw is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The operator should pay particular and additional attention to these points in order to reduce the risk of serious personal injury. Non through cutting. The blade guard is removed and top of saw blade is exposed. Contact with the blade avoid reaching towards, over and around the saw blade. Kickback- never stand in front of the blade. Stability ensure the product is stable, whenever possible, secure it. Thrown cutting blade tips wear eye protection at all times when working9 Inhalation of dust – wear a mask if necessary. Dust produced when working certain types of wood products (e.g. MDF) can be hazardous to your respiratory system. Eye injury from wood and dust particles – wear eye protection at all times when working. Hearing injury – restrict exposure and wear appropriate hearing protection. Noise levels can vary widely from machine depending on conditions of use. Persons exposed to high noise levels, even for a short time, may experience temporary partial hearing loss and continuous exposure to high levels can result in permanent hearing damage.

KNOW YOUR PRODUCT

  1. Table insert
  2. Adjustable extended riving knife
  3. Mitre guide
  4. Saw blade
  5. Saw blade guard
  6. Table insert release
  7. Fence/Rip fence
  8. Side table extension (RTS1800Es, RTS1800EF)
  9. Fixing holes (seCure to work bench or legs)
  10. On/off paddle switch
  11. Bevel angle adjustment wheel
  12. Bevel angle lock
  13.  Depth of cut handle
  14. Saw table
  15. Dust exhaust
  16. Dust port accessoryRYOBI RTS1800 Sawing Machine - 46

INSTALLATION INSTRUCTION

RYOBI RTS1800 Sawing Machine -
41 RYOBI RTS1800 Sawing Machine - 42 RYOBI RTS1800
Sawing Machine - 43 RYOBI RTS1800 Sawing Machine -
44

RYOBI RTS1800 Sawing Machine - 45

BATTERY

HOW TO FIX

RYOBI RTS1800 Sawing Machine - 48

CUTTING

RYOBI RTS1800 Sawing Machine - 49 RYOBI RTS1800
Sawing Machine - 50

HOW TO USE

RYOBI RTS1800 Sawing Machine - 51

LOCK / UNLOCK

RYOBI RTS1800 Sawing Machine - 53

Sharp bladeRYOBI RTS1800 Sawing Machine - 54

GENERAL POWER TOOL SAFETY WARNINGS

Save all warnings and instructions for future reference. the term power tool in the warmings rerers to your mains-operated (corded) power tool or battery- operated (cordless) power tool.

WORK AREA SAFETY

  • Keep work area clean and well lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
  • Power tools create sparks wcn may 1gnite the dust or fumes.
  • Keep children and bystanders away while operating a power tool.
  • Distractions can cause you to lose control.

ELECTRICAL SAFETY

  • Power tool plugs must match the outlet. Never modity the plug in any way.
  • Do not use any adapter plugs with earthed (grounded) power tools.
  • Unmodified plugs and matching Outlets will reduce risk of electric shock.
  • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
  • There is an increased risk of electric shock if your body is earthed or grounded.
  • Do not expose power tools to rain or wet conditions.
  • Water entering a power tool will increase the risk of electric shoCK.
  • Do not abuse the cord. Never use the cord for carrying, puling or unplugging the power tool
  • Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
  • When operating a power tool outdoors, use an extension cord suitable for outdoor use.
  • Use of a cord suitable for outdoor use reduces the risk of electric shocK.
  • If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
  • Use of an RCD reduces the risk of electric shock.

PERSONAL SAFETY

  • Stay alert, watch what you are doing and use common sense when operating a power tool.
  • Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
  • A moment of inattention while operating power tools may result in serious personal injury.
  • Use personal protective equipment. Always wear eye protection.
  • Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting.
  • Ensure the switch is in the off -position before connecting to power source and/or battery pack, picking up or carrying the tool.
  • Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
  • Remove any adjusting key or wrench before turning the power tool on. a rotating part of the power tool may result in personal injury.
  • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. wrench or a key left attached to Dress properly.
  • Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
  • If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
  • Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

POWER ToOL USE AND CARE

  • Do not force the power tool. Use the correct power tool for your application.
  • The correct power tool will do the job better and safer at the rate for which it was designed.
  • Do not use the power tool if the switch does not turn it on and off.
  • Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools and accessories.
  • Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation.
  • If damaged, have the power tool repaired before use.
  • Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean.
  • Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
  • Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
  • Use of the power tool for operations different from those intended could result in a hazardous situation.
  • Keep handles and grasping surfaces dry, clean and free from oil and grease.
  • Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
  • SERVICE Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR TABLE SAWs GUARDING RELATED WARNINGS

  • Keep guards in place. Guards must be in working order and be properly mounted
  • A guard that is loose, damaged, or is not functioning correctly must be repaired or replaced. Always use saw blade guard and riving knife for every through-cutting operation.
  • For through- cutting operations where the saw blade cuts completely through the thickness of the workpiece, the guard and other safety devices help reduce the risk of injury.
  • Immediately reattach the guarding system after completing an operation (such as rebating or resawing cuts) which requires removal of the guard.
  • The guard and riving knife help to reduce the risk of injury. Make sure the saw blade is not contacting the guard, riving knife or the workpiece before the switch is turned on.
  • Inadvertent contact of these items with the saw blade could cause a hazardous condition. Adjust the riving knife as described in this instructior manual.
  • Incorrect spacing, positioning and alignment can make the riving knife ineffective in reducing the likelihood of kickback.
  • For the riving knife device to work, it must be engaged in the workpiece.
  • The riving knife is ineffective when cutting workpieces that are too short to be engaged with the riving knife.
  • Under these conditions a kickback cannot be prevented by the riving knife. Use the appropriate saw blade for the riving knife.
  • For the riving knife to function properly, the saw blade diameter must match the appropriate riving knife and the body of the saw blade must be thinner than the thickness of the riving knife and the cutting width of the saw blade must be wider than the thickness of the riving knife.

CUTTING PROCEDURES WARNINGS

  • Feed the workpiece into the saw blade only against the direction of rotation.
  • Feeding the workpiece in the same direction that the saw blade is rotating above the table may result in the workpiece, and your hand, being pulled into the saw blade.
  • Never use the mitre gauge to feed the workpiece when ripping and do not use the rip fence as a length stop when cross cutting with the mitre gauge.
  • Guiding the Workpiece With the rip fence and the mitre gauge at the same time increases the likelihood of saw blade binding and kickback
  • When ripping, always apply the workpiece feeding force between the fence and the saw blade.
  • Use a push stick when the distance between the fence and the saw blade is less than 150 mm, and use a push block when this distance is less than 50 mm.
  • “Work helping” devices will keep your hand at a safe distance from the saw blade. Use only the push stick provided by the manufacturer or constructed in accordance with the instructions.
  • This push stick provides sufficient distance of the hand from the saw blade. Never use a damaged or cut push stick.
  • A damaged push stick may break causing your hand to slip into the saw blade. Do not perform any operation “freehand'”.
  • Always use either the rip fence or the mitre gauge to position and guide the workpiece.
  • “Freehand” means using your hands to support or guide the workpiece, in lieu of a rip fence or mitre gauge.
  • Freehand sawing leads to misalignment, binding and kickback. Never reach around or over a rotating saw blade.
  • Reaching for a workpiece may lead to accidental contact with the moving saw blade.
  • Provide auxiliary workpiece support to the rear and/or sides of the saw table for long and/or wide workpieces to keep them level.
  • A long and/or wide workpiece has a tendency to pivot on the table’s edge, causing loss of control, saw blade binding and kickback. Feed workpiece at an even pace.
  • Do not bend or twist the workpiece. If jamming occurs, turn the product off immediately, unplug the product then clear the jam.
  • Jamming the saw blade by the workpiece can cause kickback or stall the motor. Do not remove pieces of cut-off material while the saw is running.
  • The material may become trapped between the fence or inside the saw blade guard and the saw blade pulling your fingers into the saw blade.
  • Turn the saw off and wait until the saw blade stops before removing material. Use an auxiliary fence in contact with the table top when ripping workpieces less than 2 mm thick.
  • A thin workpiece may wedge under the rip fence and create a kickback.

SYMBOLS ON THE PRODUCT

  • Safety alert
  • CE conformity
  • EurAsian Conformity Mark
  • Class II tool, double insulation
  • Please read the instructions carefully before starting the product.
  • Wear ear protection
  • Wear eye protection.
  • Wear safety gloves.
  • Danger! Sharp blade.
  • Cutting capacity
  • Blade width of cut (kerf)
  • Number of teeth on this saw blade
  • For cutting wood and analogous material
  • Not for cutting metals
  • Blade rotation direction (shown on saw blade)
  • Blade rotation direction (shown on riving knife)
  • Blade rotation direction (shown on table)
  • Blade rotation direction (shown on blade guard)
  • Blade diameter
  • Blade body thickness and width of cut
  • Riving knife thickness and hardness
  • Rated power
  • Tungsten carbide 48 tooth blade
  • Soft start
  • Overload protection
  • Cast aluminium table
  • Table dimension (RTS1800, RTS1800S)
  • Table dimension (RTS1800ES, RTS1800EF)
  • Table extension dimension
  • Removable scissor leg
  • Foldable deluxe leg
  • Cutting capacities (90 and 45°)

SYMBOLS IN THIS MANUAL

  • Connect to power outlet.
  • Disconnect from power outlet.
  • Parts or accessories sold separately
  • Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
  • Note
  • Warning

KICKBACK CAUSES AND RELATED WARNINGS

  • Kickback is a sudden reaction of the workpiece due to a pinched, jammed saw blade or misaligned line of cut in the workpiece with respect to the saw blade or when a part of the workpiece binds between the saw blade and the rip fence or other fixed object.
  • Most frequently during kickback, the workpiece is lifted from the table by the rear portion of the saw blade and is propelled towards the operator.
  • Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.
  • Never stand directly in line with the saw blade. Always position your body on the same side of the saw blade as the fence.
  • Kickback may propel the workpiece at high velocity towards anyone standing in front and in line with the saw blade.
  • Never reach over or in back of the saw blade to pull or to support the workpiece.
  • Accidental contact with the saw blade may occur or kickback may drag your fingers into the saw blade.
  • Never hold and press the workpiece that is being cut off against the rotating saw blade.
  • Pressing the workpiece being cut off against the saw blade will create a binding condition and kickback. Align the fence to be parallel with the saw blade. A misaligned fence ill pinch the workpiece against the saw blade and create kickback.
  • Use a featherboard to guide the workpiece against the table and fence when making non-through cuts such as rebating or resawing cuts.
  • A featherboard helps to control the workpiece in the event of a kickback.
  • Support large panels to minimise the risk of saw blade pinching and kickback
  • Large panels tend to sag under their own weight. Support(s) must be placed under all portions of the panel overhanging the table top.
  • Use extra caution when cutting a Workpiece that is twisted, knotted, warped or does not have a straight edge to guide it with a mitre gauge or along the fence.
  • A warped, knotted, or twisted orkpiece is unstable and causes misalignment of the kerf with the saw blade, binding and kickback.
  • Never cut more than one workpiece, stacked vertically or horizontally. The saw blade could pick up one or more pieces and cause kickback.
  • When restarting the saw with the saw blade in the workpiece, centre the saw blade in the kerf so that the saw teeth are not engaged in the material.
  • If the saw blade binds, it may lift up the workpiece and cause kickback when the saw is restarted. Keep saw blades clean, sharp, and with sufficient set.
  • Never use warped saw blades or saw blades with cracked or broken teeth. Sharp and properly set saw blades minimise binding, staling and kickback.

TABLE SAW OPERATING PROCEDURE WARNINGs

  • Turn off the table saw and disconnect the power cord when removing the table insert, changing the saw blade or making adjustments to the riving knife or saw blade guard, and when the machine is left unattended. Precautionary measures will avoid accidents.
  • Never leave the table saw running unattended.
  • Turn it off and don’t leave the product until it comes to a complete stop. An unattended running saw is an uncontrolled hazard.

ADDITIONAL SAFETY WARNINGS FOR TABLE SAWS

  • Setup or fix the machine in a stable position appropriate for the work being done.
  • This could be mounted on a Workbench, leg support or fixed to the floor. If fitted, set the adjustable leg extension to achieve a level stable platform to work on.
  • Working at the proper height, using good working posture, will help prevent strain or other injuries during operation.
  • Provide adequate general or localised lighting to prevent stroboscopic effect and hazards.
  • Wear suitable personal protective equipment when necessary.
  • This includes hearing protection to reduce the risk of hearing loss, respiratory protection to reduce the risk of inhaling harmful dust, sturdy gloves when handling saw blades and rough material.
  • Always wear safety goggles when using the machine.
  • It is recommended to wear sturdy non slipping shoes with toe caps to protect from objects faling from the table.
  • The dust produced when using this tool may be harmful to your health, inflammable or explosive.
  • Do not inhale the dust. Use a dust extraction system and wear a suitable dust protection mask.
  • Remove deposited dust thoroughly, e.g., with a brush and vacuum cleaner.
  • Keep the floor in the working area free from excessive sawdust, cut-offs and power cables.
  • This reduces the risk of tripping and falling onto the blade.
  • Keep the table clear of objects including tools and discarded wood cut-offs. Keep the surface of the table, fence and mitre guide clean.
  • Beware of glue, paint and other items. The wood must slide smoothly and not catch or snag anywhere otherwise the risk of severe injury due to kickback is significantly increased.
  • Use only blades specified in this manual, complying With EN 847-1.
  • Do not use saw blades made of high-speed steel. Use only saw blades that are marked with a speed equal or higher than the speed marked on the tool.
  • Do not force the work piece into the cutting blade. Let the tool do the work.
  • Excessive force will overheat the blade and cutting tips, it may burn the work piece
  • It may result in unexpected events which could cause serious personal injury.
  • Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback.
  • Never use blade washers or bots that are defective or incorrect. Saw blades should be carried in a holder whenever possible.

SPECIFIC SAFETY INSTRUCTIONS FOR WOOOD CUTTING BLADE

  • Please read the manual and instructions carefully before using the saw blade and the power tool.
  • The power tool must be in good condition, the spindle without deformation and vibration.
  • Ensure the operator is adequately trained in safety precautions, adjustment and operation of the power tool.
  • Always wear goggles and ear protection the power tool. It is recommended to wear gloves, sturdy non slipping shoes and apron us
  • Before using any accessory, consult the instruction manual.
  • The improper use of an accessory can cause damage and increase the potential for injury. Keep the blade clean.
  • This includes saw dust and particularly sticky substances like wood resin. A clean blade cuts more accurately and safely.
  • Use only blades specified in this manual, complyingg with EN 847-1. Observe the maximum speed marked on the saw blade
  • Ensure the speed marked on the saw blade is at least equal to the speed marked on the saw. Always use blades with correct size and shape of arbor holes.
  • Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.
  • Do not use saw blades with a body thickness greater or a width of the groove cut (kerf) smaller than the thickness of the riving knife.
  • Do not use blades of larger or smaller diameter than recommended. Do not use any loose washers or spacers to make the blade fit onto the spindle.

OPERATION

  • Through cutting: Any cutting operation where the saw blade protrudes beyond the thickness of the workpiece.
  • For this operation the riving knife should be in the raised position and the blade guard must be fitted. Use a fence or mitre guide to correctly position the workpiece.
  • Non through cutting: Any cutting operation where the saw blade does not protrude beyond the thickness of the workpiece.
  • For this operation the riving knife should be in its lowered position. The top of the riving knife should be slightly lower than the top of the saw blade. The blade guard cannot be fitted.
  • Use a fence or mitre guide to correctly position the workpiece. Rip cutting: Using the rip fence parallel to the blade to guide the workpiece.
  • Predominantly the cut is made in the direction of the wood grain (ff present). Can be a through or non through cut. Cross cutting: Using the mitre guide or cross cutting fence.
  • This device is designed to slide parallel to the saw blade and enables the workpiece to be held at a fixed angle across the cutting axis of the blade.
  • Predominantly the cut Is made across the direction oft the wood grain (it present). Can be a through or non through cut. Bevel cutting: The angle of the blade with respect to the table surface is changed between 90 and 45°.
  • Produces a cut with an angled edge. Can be a through or non through cut.
  • Either the rip fence or the mitre guide should be used to correctly position the workpiece.

Mitre cutting: The workpiece is presented to the blade at an angle. The angle required is set on the mitre guide, which can then hold the workpiece at this angle whilst sliding parallel to the blade to make the cut. Can be a through or non through cut.

Tapered cutting: Tapered cross cuts are possible using the mitre guide set to the angle required. It is not possible to perform tapered rip cuť’s as a special fixture is required.

USING THE FENCE SAFELY

  • Never use the rip fence and the mitre angle guide at the same time
  • This increases the potential for kickback and personal injury.
  • When either is not in use, remove it from the table and store safely out of the way.
  • Each time the fence is used or moved to another position it is essential that it is checked for parallelism to the saw blade.
  • A non parallel fence can trap the workpiece between the blade and the fence causing kickback which can lead to severe personal injury to yourseir and otners.
  • A badly adjusted or set fence can cause the workpiece to be fed toward the blade at the wrong angle which may cause the blade to bind or jam.
  • It can also cause kickback (see above). To fit or adjust the fence properly, hook the end of the fence over the back edge of the table then lower the front edge to engage with the front of the table.
  • Then apply pressure from the front of the fence so that the TWO edges set at a right angle to the direction Or the fence contact the front edge of the table.
  • This helps ensure the fence is parallel to the blade. Then lock the fence in position by pushing the locking handle downwards.
  • The force by which the locking handle holds the fence in position can be adjusted by rotating the knurled Screw just above the locking handle.
  • Always check the parallelism of the fence to the blade by measurement or by an accurately cut block of wood before making the cut

OVERLOAD PROTECTION DEVICE

  • The product has an overload protection device.
  • When overloading is detected, the product will automatically switch off.
  • Turn the power off. If the overload protector is actuated, the motor must be allowed to cool down for 3 minutes.
  • Make sure the blade can rotate freely and is not jammed or tight. Press the reset button (below the on/off switch).
  • Turn the power on. Press the on button to start the product.

MAINTENANCE

Ensure the saw blade is completely stopped and the power cord is removed from the power source before conducting any maintenance or cleaning. lf the power supply cord is damaged it must be repaired at an authorised service centre. The blade has sharp edges and may also remain hot after cuting operations. Exercise extreme caution when cleaning an exposed blade. Wear gloves to protect yourself from personal injury. Clean the saw and its accessories from dust regularly, especially moving parts including the blade guard. Use a hand brush or vacuum cleaner to remove dust effectively.

CHECKING AND SETTING THE BEVEL ANGLLE NOTE

  • Setting the blade to be 90° from the table results in a 0° bevel angle.
  • Turn off the power and remove the plug from the wall SOcket.
  • Pay particular attention to the saw blade tips, they are very sharp and can cause personal injury.
  • Raise the blade and riving knife assembly to its highest height.
  • Remove the blade guard.
  • Place the riving knife to its lower position. 6. Ensure the blade and table surface are clear of dust and debris.
  • Place a 90 “set square” against the table surface and the highest part of the blade. Be careful not to contact the blade tips during this measurement as it will result in an error. You need to align the body Surtace of the saw blade.
  • There should be no gaps between the edge of the set square and the blade or the table, the blade is in a true vertical alignment and no further adjustment of the blade angle is necessary.
  • If a gap exists, loosen the bevel locking knob and carefully move the angle of the bevel whilst constantly re-checking the gap. Once no gap exists, tighten the bevel locking knob securely.
  • Loosen the screw on the bevel angle indicator and adjust the clear plastic line carrier so it shows alignment with the O mark. Tighten the screw.
  • Repeat this operation to check and set various angles between 90° and 45° as you feel necessary. his condition

GUARANTEE
In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.

  • The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
  • There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
  • The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
    • any damage to the product that is the result of improper maintenance
    • any product that has been altered or modified
    • any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
    • any damage caused by non-observance of the instruction manual
    • any non-CE product
    • any product which has been attempted to be repaired by a nonqualified professional or without prior authorization by Techtronic Industries
    • any product connected to improper power supply (amps, voltage, frequency)
    • any damage caused by external influences (chemical, physical, shocks) or foreign substances
    • normal wear and tear of spare parts
    • inappropriate use, overloading of the tool
    • use of non-approved accessories or parts
    • carburettor after 6 months, carburettor adjustments after 6 months
    • power tool accessories provided with tool or purchased separately. Such exclusions include but is not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide
    • components (parts and accessories) subject to natural wear and tear, including but not limited to carbon brushes, chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube
  • For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
  • A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries, delivery charges or postage will have to be paid by the sender.
  • This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

AUTHORISED   SERVICE   CENTRE
To find an authorised service centre near you, visit http://uk.ryobitools.eu/header/service-and-support/service-agents.

EC declaration of conformity

  • Techtronic Industries GmbH
  • Max-Eyth-Straße 10, 71364 Winnenden, Germany
  • Herewith we declare that the product
  • 4V Screwdriver
  • Brand: Ryobi
  • Model number: R4SDP

Serial number range: 44481301000001 – 44481301999999 is in conformity with the following European Directives and harmonised standards

  • 2006/42/EC, 2014/30/EU, 2011/65/EU,
  • EN 60745-1:2009+A11:2010, EN60745-2-2:2010,
  • EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+A1:2001+A2:2008

RoHS documentation is compiled according to EN 50581:2012

  • Andrew John Eyre (BEng, CEng, MIET)
  • Vice President, Regulatory & Safety
  • Winnenden, May. 10, 2016
  • Authorised to compile the technical file:
  • Alexander Krug, Managing Director
  • Techtronic Industries GmbH
  • Max-Eyth-Straße 10, 71364 Winnenden, Germany

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals