YOLINK YS4909-UC Valve Controller and Motorized Valve Kit User Guide
- October 30, 2023
- YOLINK
Table of Contents
Valve Controller & Motorized Valve Kit
YS4909-UC & DN##
Quick Start Guide
Revision Feb. 06, 2023
Welcome!
Thank you for purchasing YoLink products! We appreciate you trusting YoLink
for your smart home & automation needs. Your 100% satisfaction is our goal. If
you experience any problems with your installation, with our products or if
you have any questions that this manual does not answer, please contact us
right away. See the Contact Us section for more info.
Thank you!
Eric Vanzo
Customer Experience Manager
The following icons are used in this guide to convey specific types of
information:
| Very important information (can save you time!)
---|---
| Good to know info but may not apply to you
Before You Begin
Please note: this is a quick start guide, intended to get you started on the installation of your Valve Controller. Download the full Installation & User Guide by scanning this QR code:
https://www.yosmart.com/support/YS4909-UC/docs/instruction
Installation & User Guide
You can also find all current guides and additional resources, such as videos and troubleshooting instructions, on the Valve Controller Product Support Page by scanning the QR code below or by visiting: https://shop.yosmart.com/pages/valve-controller-product-support
https://shop.yosmart.com/pages/valve-controller-product-support
Product Support
Your Valve Controller connects to the internet via one of our hubs (original
YoLink Hub or the SpeakerHub), and it does not connect directly to your WiFi
or local network. In order for remote access to the device from the app, and
for full-functionality, a hub is required. This guide assumes the YoLink app
has been installed on your phone, and a YoLink Hub or SpeakerHub is installed
and online.
If installing the Valve Controller and motorized valve outdoors, please refer
to the environmental range information in the specifications found on the Valve
Controller product support page. While this product can be installed outdoors,
to ensure years of trouble-free operation, it should be protected from rain
and direct sunlight by an enclosure or overhead cover.
In the Kit
Required Items
These tools or items may be required:
Get to Know Your Valve Controller
LED Behaviors
| Blinking Red Once, Then Green Once
Device Start-Up
---|---
| Blinking Red And Green Alternately
Restoring to Factory Defaults
| Blinking Red Once
Valve Closing
| Quick Blinking Red Twice
Valve is Closed
| Blinking Green Once
Valve Opening
| Quick Blinking Green
Control-D2D Pairing in Progress
| Quick Blinking Red
Control-D2D Unpairing in Progress
| Slow Blinking Green
Updating
| Fast Blinking Red Once Every 30 Seconds
Low Battery, Replace Batteries Soon
**Get to Know Your Motorized Valve
**
The valve included in this kit is a 12VDC non-smart motorized valve. Use only this valve or YoLink-approved valve control products, such as the Bulldog Valve Robot. Do not use with non-YoLink valve products.
Add Your Valve Controller to the App
- Tap Add Device (if shown) or tap the scanner icon:
- Approve access to your phone’s camera, if requested. A viewfinder will be shown on the app.
- Hold the phone over the QR code so that the code appears in the viewfinder.If successful, the Add Device screen will be displayed.
- Follow the instructions to add your Valve Controller to the app.
Install the Valve Controller
Preparing for installation:
Determine where you will install your Valve Controller. Typically, it should
be wall-mounted, no farther away from the motorized valve than the length of
the cables allow (if you have purchased optional extension cables, the valve
controller can be installed at a location separate from the motorized valve).
Determine how you will mount the valve controller to the wall, and have
hardware and anchors appropriate for the wall surface on hand.
- At the desired location for the controller, confirm the cables of the two devices will reach each other. Holding the controller at the desired location, and using a marker or similar means, mark the location of the mounting hole to the wall or mounting surface.
- If you are using a wall anchor, install it at this time, per the manufacturer’s instructions.
- Secure the Valve Controller to the wall or mounting surface with a screw, as shown.
Install the Motorized Valve
- Shut-off the water serving the pipe where the valve is to be installed. Drain the water from the pipe, by turning on a faucet, or by other method as required.
- Depending on the adapter fitting used, measure the length of pipe that must be cut, and mark the cut lines on the pipe, as shown below.
- Cut the water pipe through the mark using a pipe cutting tool, then remove the cut section of pipe, as shown below.
- Sand both ends of cut pipe, removing any burrs or rough edges. Use care handling the cut edges, which may be sharp! Wipe off the cut section of pipe with a clean cloth.
- Install your adapter fittings in the pipe ends, per the manufacturer instructions.
- Wrap each adapter’s threaded end with thread seal tape, per the tape manufacturer’s instructions, as shown below.
- Install the motorized valve on the adapter fittings, ensuring a secure connection at each fitting, as shown below.
- At the water valve or point of disconnection, turn the water on again.
- Verify there are no leaks and no visible water on the motorized valve.
Power Up, Final Connections & Testing
- Install batteries in the Valve Controller. This is done by releasing the two clamp latches on the side of the controller, then opening the cover. Then, install the batteries.
- Close the cover, snapping the clamp latches tightly into the locked position.
- Connect the Valve Controller’s cable to the control cable of the motorized valve. Ensure the arrow on the cable connector aligns with the arrow on the other cable connector. Twist the collar of the connector tight.
- The Valve Controller will appear offline until it is turned on and it wirelessly connects to a YoLink hub. Turn on the Valve Controller by pressing the SET button, just long enough for the LED to illuminate. It should blink red, then green, which indicates the Valve Controller has connected to the cloud.
- Test the Valve Controller and motorized valve by pressing the SET button and listening for the smooth closing/opening of the valve, and by checking the water flow at a faucet. The water should be completely turned off while the valve is in the shut position.
Refer to the full installation and user guide to complete the setup of your
Valve Controller and motorized valve.
Your Valve Controller is supplied with alkaline batteries. If you elect to
replace the batteries with lithium type batteries, please note, in very cold
temperatures, the battery level may be indicated in the app as lower than it
actually is. This is characteristic of lithium batteries.
Contact Us
We are here for you, if you ever need any assistance installing, setting up or
using a YoLink app or product!
Need help? For fastest service, please email us 24/7 at
service@yosmart.com
Or call us at 831-292-4831 (US phone support hours: Monday – Friday, 9AM to
5PM Pacific)
You can also find additional support and ways to contact us at:
www.yosmart.com/support-and-service
Or scan the QR code:
http://www.yosmart.com
/support-and-service
Support Home Page
Finally, if you have any feedback or suggestions for us, please email us at
feedback@yosmart.com
Thank you for trusting YoLink!
Eric Vanzo
Customer Experience Manager
15375 Barranca Parkway
Ste. J-107 | Irvine, California 92618
© 2022 YOSMART, INC IRVINE,
CALIFORNIA
Documents / Resources
|
YOLINK YS4909-UC Valve Controller and Motorized Valve
Kit
[pdf] User Guide
YS4909-UC Valve Controller and Motorized Valve Kit, YS4909-UC, Valve
Controller and Motorized Valve Kit, Motorized Valve Kit, Valve Kit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>