BLUSTREAM DA11ABL-WP-EU Bluetooth and Analogue Audio Dante Wall Plate User Guide
- June 13, 2024
- BLUSTREAM
Table of Contents
DA11ABL-WP-EU
Quick Reference Guide
Introduction
The DA11ABL-WP-EU is a multi-input / output wall plate to convert Bluetooth
and analogue audio within a digital Dante® networked audio system. The
DA11ABL-WPEU converts 2 x input channels of Bluetooth, or unbalanced audio to
Dante® digital audio, and 2 x channels of Dante® audio to 2 x output channels
of unbalanced audio.
The DA11ABL-WP-EU is a plug & play device that is powered using PoE (Power
over Ethernet), or via 12V power supply, offers support for AES67 RTP audio
transport, and magnetic faceplate design allows for both UK & EU backbox
compatibility. The DA11ABL-WP-EU is the ideal BYOD interface to allow any
Bluetooth device to stream audio wirelessly to a Dante® audio system.
FEATURES:
- Dante® network wall plate interface for Bluetooth and analogue L/R audio inputs, and L/R audio outputs
- Converts 2ch Bluetooth, or un-balanced audio sources to Dante® audio
- Converts 2x Dante® audio channels to un-balanced audio outputs
- Adjustable input sensitivity from +24dBu to -28dBV via control sošware
- Adjustable output gain from +20dBu to -28 dBV via control sošware
- Supports: 44.1, 48 & 96kHz sample rates @ 16, 24 or 32 Bit
- Configurable Dante® device latency (supports 1, 2 or 5ms configurable using Dante® Controller)
- Supports AES67 RTP audio transport
- Features Class 0 IEEE 802.3af PoE for powering of product from any PoE switch
- Supports power via 12V DC adapter (supplied) for when network switch does not support PoE
- Magnetic faceplate surround allowing for both UK & EU backbox compatibility
Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk
Front Panel
Connections:
- Power Status Indicator – Illuminates when the devices is powered on power input
- Bluetooth Status Indicator – Illuminates when Bluetooth device is connected
- ID LED Indicator – Flashes when this device is identified through Dante® Configurator
- Analogue Audio Input – 3.5mm stereo jack for unbalanced analogue audio input
- Bluetooth Pair Button – Press to make device discoverable for Bluetooth pairing, press 2 to 3 times to change audio source selection
- Micro USB Port – Used for software control and firmware updates
- Analogue Audio Output – RCA L / R connector unbalanced analogue audio output
Rear Panel
Connections:
- Dante® Network Connection (PoE) – RJ45 connection to connect to network switch
- Power Port – Use 12V/1A DC adaptor (not included) when PoE is not available to power device
Bluetooth
Bluetooth 5.0 technology allows for 2x simultaneous connections from source
audio devices, where the selected devices audio is received and sent into the
Dante network.
To connect a Bluetooth enabled device to the DA11ABL-WP-EU, press the Pair
button on there unit, go to the Bluetooth settings of the source audio device,
and enable Bluetooth connectivity. The DA11ABL-WP-EU will appear in the list
of available devices.
Dante® Controller
Dante® Controller software is required in order to set up and configure the
DA11ABL-WP-EU as well as control the Dante® network. Audinate provide
extensive training videos and documentation on their website. This can be
found here: http://www.audinate.com/products/
software/dante-controller
Upon connecting your DA11ABL-WP-EU to a compatible network, the Dante®
Controller software should automatically discover the device. The DA11ABL-WPEU
will appear in the Dante®
Controller with a name prefixed with “DA11ABL-WP-EU”. On the “Routing” screen
you can create audio routing between Dante® transmitters and receivers in the
system.
Please ensure your PC is on the same network as your Dante® devices. Dante® is
not able to transmit over WiFi, and it is recommended to hardwire into the
Dante® network. Having multiple network devices enabled can also confuse the
Dante® Controller software so it is recommended to disable WiFi during
configuration.
Advanced Dante® Settings
By default the DA11ABL-WP-EU is shipped with its network settings set to
obtain an IP address automatically. This means that if a DHCP server is
present on your network, it will provide the DA11ABLWP-EU with an IP address.
If no DHCP server is present then the DA11ABL-WP-EU will receive a default IP
address in the 169.254.xxx.xxx range.
To change the IP address of the DA11ABL-WP-EU, you must enter the “Network
Config” menu in the “Device Info” screen of the Dante® Controller software. It
is also possible to change the settings of the
DA11ABL-WP-EU under the “Device Info” screen in the Dante® Controller
software. To do so, select the “Device Config” menu.
The sample rate of the DA11ABL-WP-EU can be adjusted here. Please note: Dante®
products can only transmit or receive audio from other Dante® products that
are set up with the same sample rate.
A mismatch in sample rate may stop audio from transmitting.
Under the “Device Config” screen we can also adjust the latency of the
DA11ABL-WP-EU from 1, 2 or 5 milliseconds.
Specifications
Audio Input Connectors: 1 x Analogue Le / Right audio (3.5mm stereo jack)
Audio Output Connectors: 2 x Analogue RCA (Le / Right)
Network Connectors: 1 x PoE Dante® Ethernet Connection (RJ45)
Bluetooth: Bluetooth V5.0 – SBC / MP3 / AAC / APT-X / APTX-LL / APTX-HD, 44
.1K-48KHz 16 / 24Bit
Configuration Switches: 1 x Push button (connect / selection)
Firmware Upgrade: 1 x Micro-USB UART port
Module Dimensions (W x H x D): 74mm x 74mm x 50mm (without faceplate)
Faceplate Dimensions (W x H x D): 85mm x 85mm x 5mm
Cut Out Dimensions (W x H x D): 52mm x 55mm x 38mm
Mounting Hole Spacing: UK 60mm CTC, EU 60mm CTC
Backbox Requirements: UK single gang backbox / EU single gang backbox
Shipping Weight: 0.3kg
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Storage Temperature: – 4°F to 140°F (- 20°C to 60°C)
Power Supply: Class 1 IEEE 802.3af POE PD or 12V/1A DC, 2-Pin Phoenix
connector
Package Contents
• 1 x DA11ABL-WP-EU
• 1 x Magnetic Faceplate
• 1 x Quick Reference Guide
Acknowledgements
Dante® is a registered trademark of Audinate Pty Ltd.
Certifications
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o¤ and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit di¤erent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION – changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmentally safe
recycling.
RF EXPOSURE
To maintain compliance with FCC’s RF Exposure g uidelines, This equipment s
hould be installed a nd operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
CANADA, INDUSTRY CANADA (IC) NOTICES
This device contains licence-exempt transmitter(s)/receiver(s) that omply with
Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
This device may not cause interference.
This device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
References
- Register a .US.COM domain today!
- Products | Audinate | Dante Pro AV Networking
- blustream-us.com
- blustream.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>