BLUSTREAM HMX88-18G 4K HDBaseTTM3 AV Matrix User Guide
- June 2, 2024
- BLUSTREAM
Table of Contents
- BLUSTREAM HMX88-18G 4K HDBaseTTM3 AV Matrix
- Product Usage Instructions
- Introduction
- FEATURES
- Front Panel Description
- Rear Panel Description
- Web-GUI Control
- RS-232 Configuration
- EDID Control
- Specifications
- Package Contents
- Certifications
- Information
- Maintenance
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BLUSTREAM HMX88-18G 4K HDBaseTTM3 AV Matrix
Specifications :
- Model : HMX88-18G
- Technology : HDBaseTTM 3
- Resolution : HDMI 2.0 4K 60Hz 4:4:4
- HDCP Version : 2.3/2.2
- Transmission : Up to 100m over a single CAT6A cable
- Audio Matrix : 26×8 independent matrix
- Features : HDR10/10+, Dolby Vision, ARC support, Ethernet pass through
Product Usage Instructions
Front Panel Description:
- IR Receiver Window: Receives IR signals for control
- Menu Button: Access Matrix menu
- Selection Buttons: Select HDMI outputs and inputs
- ESC: Exit MENU mode
Rear Panel Description:
- IR Control Input: Connects to IR receiver for control
- TCP/IP: RJ45 connector for control of the Matrix
- Ethernet Passthrough: RJ45 connector for network data to receivers
- RS-232: Phoenix connector for RS-232 control
- Upgrade Port: For firmware updates
- IR Outputs: Connects to IR emitter for source control
- Audio Outputs: Toslink + 3.5mm L/R line level stereo jack
- IR Inputs: Extends IR from Matrix to HDBaseTTM Outputs 1-8
Frequently Asked Questions (FAQ):
-
What is the maximum transmission distance supported by the HMX88-18G Matrix?
The transmission distance is subject to video format, cable type, and installation environment. It is recommended to use a minimum of CAT6A cabling. -
How can I perform a factory reset on the Matrix?
To perform a factory reset, press and hold the ‘X’ button for 10 seconds. Press the select button to confirm or any other button to cancel. -
What audio formats are supported by the analogue audio outputs?
The analogue audio outputs support 2-channel PCM audio format. -
How do I update the firmware of the Matrix?
-
You can update the firmware using the upgrade port on the rear panel. Connect the device for firmware updates.
HMX88-18G
Quick Reference Guide
Introduction
- The HMX88-18G Matrix is an industry leading uncompressed, unconverted HDMI 2.0 4K 60Hz 4:4:4 HDCP 2.3/2.2 solution utilising HDBaseT™ 3 technology to deliver HDMI,
- Bi-directional IR & RS-232, ARC, 1Gb Ethernet, and PoC up to lengths of 100m over a single CAT6A cable.
- The HMX88-18G supports uncompressed distribution of the latest HDR resolutions including HDR10/10+ and Dolby Vision resulting in the ultimate in picture quality for your critical viewing areas.
- The Matrix also provides advanced features including simultaneous HDBaseT™/HDMI on outputs 1 & 2, video smart scaling on HDBaseT outputs, and an independent 26×8 audio matrix and ARC. The HMX88-18G includes an in-built web browser interface module for control and configuration of the Matrix, and RS-232, IR and Ethernet pass through to enable seamless 3rd party control integration.
FEATURES
- Advanced uncompressed, unconverted, HDMI over HDBaseT™ technology offering distribution of bit-for-bit 4K HDMI video and audio over a single CAT6A cable
- Features 8 x HDMI inputs which can be independently routed to 8 x HDBaseT™ outputs
- Outputs 1 & 2 feature simultaneous HDMI and HDBaseT™ outputs
- Supports distribution of uncompressed HDMI2.0 18Gbps specification including 4K 60Hz 4:4:4 UHD video up to 100m*
- Supports distribution of the latest HDR resolutions including HDR10/10+ and Dolby Vision
- 26×8 Audio Matrix independently controllable from video. Audio source inputs include:
- 8 x audio breakout from HDMI source inputs
- 8 x audio breakout from zone outputs
- 8 x audio return from zone outputs*
- 1 x Optical and 1x Analogue audio input
- Supports all known HDMI audio formats including Dolby TrueHD, Dolby Atmos, Dolby Digital Plus and DTS-HD Master Audio transmission
- Integrated Ethernet switch (LAN Serving) when used with Blustream RX18G receiver (1Gb maximum)
- Web interface module for control and configuration of the Matrix
- Supports bi-directional IR and RS-232 on all HDBaseT™ outputs
- Control via front panel, IR, iOS / Android App, RS-232 and TCP/IP
- Supports PoC (Power over Cable) to power compatible HDBaseT™ receivers
- Advanced EDID management and HDCP 2.3 compliant
- Transmission distance is subject to video format, cable type and installation environment. It is recommended to use a minimum of CAT6A cabling
- ARC feature supports HDMI ARC or Optical ARC. Compatible with RX18G only
Front Panel Description
- IR Receiver Window
- LCD Display – Shows the status of input / output selection, EDID etc…
- Menu Button – Press to access Matrix menu. Refer to full online manual for details
- Power Button – Press to power on / off the Matrix
- Selection Buttons – Multi-use buttons
- Primary Use:
- First press = HDMI output selection – Press to select output/s from 1 to 8. Output(s) selected will be displayed on the Matrix display. Multiple outputs can be chosen. Then wait 3 seconds or press ‘SELECT’ to move to input selection.
- Second Press = HDMI input selection – Press to select the input from 1 – 8. The Input selected will be displayed on the Matrix display. Press the Select button to confirm switch
- Select Button – Press to confirm changes within the Matrix menu
- ESC – Press to exit MENU mode
- Secondary Use:
- When the MENU button has been pressed buttons 3, 4, 7 & 8 are used as cursors to navigate the MENU system
- 3 = Left, 4 = Up, 7 = Right, 8 = Down
- The matrix can be factory reset by pressing and holding ‘X’ for 10 seconds, press the select button to confirm, or any other button to cancel.
Rear Panel Description
- IR Control Input – 3.5mm stereo connector to connect to Blustream IR receiver for IR control of the Matrix
- TCP/IP – RJ45 connector for TCP/IP and web-GUI control of the Matrix
- Ethernet passthrough – RJ45 connector for Ethernet passthrough of network data to compatible HDBaseT™ receivers
- RS-232 – Phoenix connector for RS-232 control of the Matrix
- EDID DIP switch – Used for global EDID settings
- Upgrade port – Used for firmware updates
- IR Outputs – 3.5mm mono connector to connect to Blustream IR emitter. Used for local source control
- Optical and Analogue Audio Outputs – independent audio Matrix with 8 x dual outputs (Toslink + 3.5mm L/R line level stereo jack). For connection to 3rd party audio devices. NOTE: Analogue audio outputs support 2ch PCM only
- IR Inputs – 3.5mm stereo connector to connect to Blustream IR receiver or Control Processor. Used to extend IR from Matrix to HDBaseT™ Outputs 1-8 connect to Blustream IR receiver or Control Processor. Used to extend IR from Matrix to HDBaseT™ Outputs 1-8
- Bi-directional RS-232 ports. Connect to third party control device to extend RS-232 commands to HDBaseT™ receivers RS-232 port
- Optical (Toslink) Audio Input – Connect to source device for audio distribution within the HMX88-18G independent audio Matrix
- Analogue Audio Input – 3.5mm L/R stereo jack. Connect to source device for audio distribution within the HMX88-18G independent audio Matrix
- HDMI Inputs – Connect to source devices
- HDMI Output – Connect to display / AVR device y HDBaseT™ Outputs – RJ45
- HDBaseT™ port to connect to the HDBaseT™ input port of the compatible Blustream HDBaseT™ receiver
- IEC Power Socket – Use supplied IEC power cable
- Power Switch
Web-GUI Control
- The HMX88-18G features an in-built web-GUI which can be used for control and configuration of the Matrix. By default the matrix is set to DHCP, however if a DHCP server (eg: network router) is not installed, the matrix IP address will revert to the below details: Default Username is: Blustream Default Password is: 1234 Default IP Address is: 192.168.0.200
- For further information please see the HMX88-18G User Manual – available to download from the Blustream website.
RS-232 Configuration
The RS-232 port is used for configuration and control of the product, as well
as pass-through of RS-232 commands to a compatible Blustream HDBaseT™
receiver.
The default RS-232 communication settings are:
- Baud Rate : 57600
- Data Bit : 8
- Stop Bit : 1
- Parity Bit : none
For a complete RS-232 command list please see the HMX88-18G User Manual – available to download from the Blustream website.
EDID Control
- EDID (Extended Display Identification Data) is a data structure that is used between a display and a source. This data is used by the source to find out what audio and video resolutions are supported by the display then from this information the source will discover what the best audio and video resolutions that need to be output.
- While the objective of EDID is to make connecting a digital display to a source a simple plug and play procedure, issues do arise when multiple displays or video matrix switching is introduced because of the increased number of variables.
- By pre-determining the video resolution and audio format of the source and display device you can reduce the time need for EDID handshaking thus making switching quicker, and more reliable.
Configuration of Matrix EDID settings can be acheived in one of three ways:
- Using Matrix web browser interface
- Using Matrix front panel (see below)
- Using Matrix EDID DIP switches (see product User Manual)
To change the input signal type using the Matrix front panel press the following:
Using Matrix Front Panel Buttons:
-
Press the MENU button
-
Scroll down to ‘EDID Management’. Press the SELECT button to enter into EDID configuration mode
-
Scroll through EDID management options and select ‘Built-In EDID’ or ‘Copy Output xx’
Built-In EDID Selection : -
Select the input you wish to fix the EDID on (1-8) or select ‘All’. Use UP/DOWN buttons to toggle the selection and press the SELECT button to move to EDID selection
-
Select video resolution + audio format required (4K, 1080p, 3D, 2ch, 5.1 etc). Use UP/DOWN buttons to toggle the selection and press the SELECT button to apply. The SELECT button LED will flash orange when complete
Copy Output EDID: -
Select the HDBaseT™ output you wish to copy the EDID from. Use UP/DOWN buttons to toggle the selection and press the SELECT button to move to the input selection that you wish to copy the EDID to
-
Select the HDMI input (1-8) or select ‘All’ to copy to all HDMI inputs. Press the SELECT button to apply
Specifications
- Video Input Connectors: 8 x HDMI Type A, 19-pin, female
- Video Output Connectors : 2 x HDMI Type A, 19-pin, female, 8 x HDBaseT™ RJ45 connectors
- Audio Input Connectors : 1 x Analogue audio L/R (3.5mm stereo Jack), 1 x Optical (S/PDIF)
- Audio Output Connectors : 8 x Analogue audio L/R (3.5mm stereo Jack), 8 x Optical (S/PDIF)
- RS-232 Serial Port : 9 x 3-pin phoenix connector
- TCP/IP Control Port : 1 x RJ45, female
- Ethernet Passthrough Port : 1 x RJ45, female
- IR Input Ports : 10 x 3.5mm stereo jack
- IR Output Ports : 9 x 3.5mm mono jack
- Product Upgrade Port : 1 x Micro USB, female
- Rack Mountable: 2U rack height, rack ears included
- Casing Dimensions (W x H x D): 436mm x 88mm x 400mm (without feet)
- Shipping Weight: 10.5kg
- Operating Temperature: 23°F to 131°F (-5°C to +55°C)
- Storage Temperature : -13°F to 158°F (-25°C to +70°C)
- Power Supply: Internal 100-240V AC
- HDBaseT Power Output : 24V DC 0.75A per port
Package Contents
- 1 x HMX88-18G
- 1 x Rack mounting kit
- 1 x Remote control
- 8 x IR emitters
- 9 x IR receivers
- 1 x Serial Cable – DB9 to 3-pin phoenix connector
- 1 x IR Control Cable – 3.5mm-3.5mm Cable
- IEC Power Cable(s)
- 1 x Quick Reference Guide
NOTE: Specifications are subject to change without notice. Weights and dimensions are approximate.
Certifications
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
- If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION – changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmentally safe
recycling.
Information
- Read these instructions – All the safety and operating instructions should be read before this product is operated.
- The apparatus should be connected to a mains socket outlet with a protective earthing connection.
- The socket-outlet shall be installed near the equipment and shall be easily accessible.
- Do not ingest battery, Chemical Burn Hazard
- This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
- WARNING: Please refer the information on exterior bottom enclosure for electrical and safety information before installing or operating the apparatus.
Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.
Notes…
HMX88-18G_QRG_REVA5
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>